Table of Contents
Advertisement
Quick Links
RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE
INSTALLATION
INSTRUCTIONS
36" Wood Burning Fireplaces
P/N 800,018M REV. D 04/2002
MODELS
DM36HCI
This installation manual will enable you to obtain a safe, efficient and
dependable installation of your fireplace system. Please read and under-
stand these instructions before beginning your installation.
Do not alter or modify the fireplace or its components under any
circumstances. Any modification or alteration of the fireplace system,
including but not limited to the fireplace, chimney components and
accessories, may void the warranty, listings and approvals of this system
and could result in an unsafe and potentially dangerous installation.
IMPORTANT! TO ASSURE PROPER ALIGNMENT OF GLASS DOORS:
INSTALL THIS FIREPLACE IN A SQUARE AND PLUMB CONDITION,
USING SHIMS AS NECESSARY AT SIDES AND/OR BOTTOM.
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
DESIGNER 36
FIREPLACES
WH Report No. 764-12354
1
Advertisement
Table of Contents
Related Manuals for Intertherm DESIGNER 36
Summary of Contents for Intertherm DESIGNER 36
- Page 1 INSTALLATION INSTRUCTIONS DESIGNER 36 FIREPLACES 36" Wood Burning Fireplaces P/N 800,018M REV. D 04/2002 MODELS DM36HCI This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and under- stand these instructions before beginning your installation.
-
Page 2: Table Of Contents
TABLE OF CONTENTS 3. This fireplace must be installed with The manufacturer is not responsible for any FireCraft's FTF8 (8" inside diameter) Chimney smoking or related problems that may result System only. These systems are intended for from the lack of adequate combustion air. It is Safety Rules ........ -
Page 3: Precautions
PRECAUTIONS These models are designed as heat circulating WARNING: FAILURE TO USE MANUFAC- fireplaces and may be fitted with accessory TURE PROVIDED PARTS, VARIATIONS IN fans. Note: These fireplace systems are not difficult TECHNIQUES AND CONSTRUCTION MA- to install. However, in the interest of safety, it is TERIALS OR PRACTICES OTHER THAN Note: Illustrations shown reflect “typical”... -
Page 4: Assembly Outline
Chimney Enclosure WARNING: DO NOT OBSTRUCT THE COL- LAR OPENINGS AROUND THE BASE OF Construct a box-like framed structure to sur- THE CHIMNEY AT THE TOP OF THE FIRE- round the fireplace and chimney within the PLACE. NEVER USE BLOWN INSULA- confines of the manufactured home, not neces- Hearth TION TO FILL THE CHIMNEY ENCLOSURE. -
Page 5: Preinstallation Notes
3. Connect house wiring to the fireplace for CAUTION: DO NOT BLOCK THE HEAT-CIRCU- Top Spacer later attachment of optional blower. LATING AIR INLET AND OUTLET PORTS ON CIRCULATING MODELS. DOING SO MAY RE- Maintain 4. Install optional outside combustion air kit. SULT IN A POTENTIAL FIRE HAZARD. -
Page 6: Fireplace Specifications
FIREPLACE SPECIFICATIONS 12 ¹⁄₂" (318 mm) 9" (229 mm) 16 ¹⁵⁄₁₆" (428 mm) 1 ¹⁄₂" Metal Safety Strips 36" 44 ¹⁄₄" (914 mm) (1124 mm) 20 ³⁄₁₆" 2 ⁷⁄₈" Figure 7 (513 mm) (73 mm) 7 ¹⁄₈" (181 mm) Blocking 41 ³⁄₄"... -
Page 7: Framing Specifications
FRAMING SPECIFICATIONS Framing Dimensions 43" 1092 mm Back Wall of Chase/Enclosure 44 ¹⁄₂" Including Finising 1130 mm Materials if any 29 ¹⁄₂" 749 mm 15 ³⁄₄" 400 mm 73" 1854 mm Header 36 ¹⁄₂" 927 mm 21 ³⁄₄" 552 mm Rough Framing Face 20 ³⁄₄"... -
Page 8: Installing The Chimney System
Step 4. Fireplace should be secured to side In new construction, to determine chimney cen- Attic Above framing members using the full length nailing ter line, use plumb line from roof or ceiling above 2” tabs at the top and bottom of the fireplace front fireplace to center of flue collar on fireplace. - Page 9 Outer pipe section installs in just the opposite Install the Model FTF8-S4 stabilizer by fitting Outer Pipe Of Thimble Cathedral Chimney way; the lanced end goes down and each new inner section down into respective section of Ceiling section goes OVER the outside of the previous proceeding flue pipe and locking outer stabilizer section installed ( Figure 23 ).
-
Page 10: Ten Foot Rule Summary
Note: If chimney extends more than 8' above Step 7. Secure flashing by nailing along the 3. Center outer locking section over outer flue perimeter into roof using 8d nails or equivalent roof surface, guy wires are also recommended. pipe. Push down until locking tabs are firmly fasteners. -
Page 11: Chimney Component Calculations
FTF8 CHIMNEY COMPONENT Maximum offset of chimney system is 30°. Room Above Two offsets must not be assembled to form a CALCULATIONS F8FS30-2 60° offset. However, two sets of offset and 2" Min. Firestop Spacer Air Space return elbows may be used on a single flue The minimum installed height of the com- system, provided the total height of the sys- pleted fireplace system is 10' 6". -
Page 12: Vertical Elevation Chart
FTF8 VERTICAL ELEVATION CHART Height Of Number Of FTF8 Height Of Height Of Number Of FTF8 Height Of Chimney Only Chimney Lengths Chimney Only Chimney Only Chimney Lengths Chimney Only Inches Feet/Inches 12" 18" 36" 48" Inches Feet/Inches 12" 18" 36"... -
Page 13: Offset Elevation Chart
FTF8 OFFSET ELEVATION CHART FTF8-ES30 Number of FTF8 Offset Height Offset/Return FTF8-S4 Chimney Sections Offset Height (Inches) (Inches) Elbow Set Stabilizer 12" 18" 36" 48" (mm) (mm) 15 ³⁄₄ 24 ¹⁄₂ 29 ³⁄₄ 14 ¹⁄₄ 33 ¹⁄₂ 17 ¹⁄₄ 38 ¹⁄₂ 20 ¹⁄₄... -
Page 14: Installing Offsets
Note: See Framing and Dimension Chart for the OPTIONAL EQUIPMENT sizes of the ceiling and roof openings. The size CONSIDERATIONS of the roof opening varies with the degree of pitch of the roof. Blower Kit Offset Elbow Assembly A Blower Kit model FBK-200 is available for use with these models. -
Page 15: Combustion Air Kits
This provision is intended for connection to a THIS FIREPLACE IS NOT INTENDED TO BE Combustion Air Actuator decorative gas appliance incorporating an au- USED AS A SUBSTITUTE FOR A FURNACE TO HEAT AN ENTIRE HOME. USE FOR SUPPLE- tomatic shut-off device and complying with MENTARY HEATING ONLY. -
Page 16: Glass Doors
Glass Doors It is especially important to insulate between The hearth extension must extend 8" beyond the studs of an outside chase cavity and under both sides of the fireplace opening and 16" beyond the front ( Figure 45 ). Use a hearth the floor if the floor is above ground level. - Page 17 Answer using r = 0.51 x ⁵⁄₈" = 0.32 = ³⁄₈" A ³⁄₄" marble slab set in ¹⁄₂" mortar covers the ³⁄₈" thickness Micore will be required. brick, “R” for the marble and mortar becomes: Wall Shield Required Where Less Than 12" = 0.09 x ³⁄₄"...
-
Page 18: Finish Requirements
FINISH TO YOUR TASTE INSTALLATION COMPONENTS There are a wide variety of “finished looks” for The following items are available for use in the these fireplaces, from formal wall decor with installation of this appliance. elaborate mantels to rustic wood paneling or warm brick facings. - Page 19 INSTALLATION COMPONENTS Round Termination 63L42 FTF8-CTD Thimble Extension 2" 19M52 F8-TE26-2 Storm Collar 63L59 Adjustable Firestop/Thimble HO326 FM8-AT2 Stabilizer 63L25 FTF8-S4 Cold Climate Kit 63L62 FTF8-CCK2-LD Locking Band 63L60 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
- Page 20 The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. Printed in U.S.A. © 2001 by LHP 1110 West Taft Avenue P/N 800,018M REV.