Installation Instructions - Kenmore 2671532 Use & Care Manual

BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT- Save these instructions for local inspector's
use.
• IMPORTANT- Observe all governing codes and ordinances.
• Note to Installer - Be sure to leave these instructions with
the customer.
• Note to Customer - Keep these instructions for future refer-
ence.
• Before the appliance is removed from service or discarded,
remove the washer and dryer door.
• Inspect the dryer exhaust outlet and straighten the outlet
walls if they are bent.
• Service information and the wiring diagram are located at
the access panel.
• Do not allow children on or in the appliance. Close supervi-
sion of children is necessary when the appliance is used
near children.
• Install the appliance where the temperature is above 50° F
(10° C) for satisfactory operation of the dryer control sys-
tem.
Tools You Will Need
10” Adjustable Wrenches (2)
8” Pipe Wrench
WARNING RISK OF FIRE
• To reduce the risk of severe injury or death, follow all installation
instructions.
• Appliance installation must be performed by a qualified in-
staller.
• Install the appliance according to these instructions and in ac-
cordance with local codes. In the absence of local codes, instal-
lation must comply with National Fuel Gas Code, ANSIZ223.1/
NFPA 54 or the Canadian Natural Gas and Propane Installation
Code, CSA B149.1.
• California Safe Drinking Water and Toxic Enforcement Act. This
act requires the governor of California to publish a list of sub-
stances known to the state to cause cancer, birth defects or
other reproductive harm and requires businesses to warn cus-
tomers of potential exposure to such substances. Gas appliances
can cause minor exposure to four of these substances, namely
benzene, carbon monoxide, formaldehyde and soot, caused pri-
marily by the incomplete combustion of natural gas or LP fuels.
Properly adjusted dryers will minimize incomplete combustion.

INSTALLATION INSTRUCTIONS

1/4” Nutdriver Flat Blade Screwdriver
Slip Joint Pliers
Level
Exposure to these substances can be minimized further by prop-
erly venting the dryer to the outdoors.
• This appliance must be exhausted to the outdoors.
• Use only 4" rigid metal ducting for exhausting the appliance to
the outdoors.
• DO NOT install a clothes dryer with flexible plastic ducting ma-
terials. If flexible metal (semi-rigid or foil-type) duct is installed,
it must be UL listed and installed in accordance with the instruc-
tions found in the section "Connecting The Dryer To House Vent"
on this Use & Care Guide. Flexible venting materials are known
to collapse, be easily crushed, and trap lint. These conditions will
obstruct dryer airflow and increase the risk of fire.
• Do not install or store this appliance in any location where it
could be exposed to water and or weather.
• Save these instructions. (Installers: Be sure to leave these instruc-
tions with the customer).
In the state of Massachusetts, installation must be per-
formed by a qualifiedor licensed contractor, plumber, or
gasfitter qualified or licensed by the state.
• When using ball type gas shut-off valves, they should be
T-handle type.
• A flexible gas connector, when used, must not exceed 3
feet.
Materials You Will Need
4” Dia. Metal Duct
4” Diam. Metal
(Recommended)
4” Dia. Flexible Metal (Semi-Rigid)
UL Listed Transition Duct
(If Needed)
Kit WX08X10077 (Includes 2 Elbows)
4” Dia. Flexible Metal (Foil Type)
UL Listed Transition Duct
(If Needed)
4” Cover Plate (If Needed)
(Kit WE1M454)
Parts Supplied
2 Rubber Washers
(washers may be
2 Washer Hoses
Exhaust Hood Pipe Compound
Elbow
4” Duct Clamps (2)
or
Duct Tape
4” Spring Clamps (2)
Flexible Gas Line Connector
Soap Solution For
Leak Detection Safety Glasses
2 Stainer Screens/
Ruber Washers
in water hoses)
1 Cable Tie
Gloves
19