1. Introduction Thank you for purchasing ASRockInd IMB-R1000 motherboard, a reliable motherboard produced under ASRockInd’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRockInd’s commitment to quality and endurance. In this manual, chapter 1 and 2 contains the introduction of the mother- board and step-by-step hardware installation guide.
1.2 Specifications Form Dimensions Mini-ITX (6.7-in x 6.7-in) Factor AMD Ryzen FP5 BGA package, 14nm process, with CPU option 12W~25W (IMB- Processor R1000M(R1606G), R1000V(R1505G)) System Chipset PCIe 1 x PCIe x 4 Mini-PCIe 1 x Full/Half mini-PCIe with PCIe x1 and USB 2.0 Expansion 1 x M.2 (Key E, 2230) with PCIe x1 and USB2.0 Slot...
Page 6
4 x USB2.0, 1 x USB 2.0 (Type A) LVDS/ inverter 1 (Shared with DP0) 1 (Shared with DP3) 4 x COM (RS-232, COM6 shared with Serial ccTalk) Internal SATA 2 x SATA3 (6.0Gb/s) Connector GPIO 8 x GPI, 8 x GPO (Shared with LPT) SATA PWR Output Speaker...
1.4 I/O Panel DisplayPort (DP0) USB 2.0 Ports (USB2H_2_3) Serial Port (COM3)* USB 3.0 Ports (USB3_1_2) LAN RJ-45 Port (LAN1)** Serial Port (COM4)* LAN RJ-45 Port (LAN2)** 10 DisplayPort (DP3) Front Speaker (Lime) 11 DisplayPort (DP1) Microphone (Pink) 12 DC Jack (DC_JACK1)*** * This motherboard supports RS232/422/485 on COM3, 4 ports.
Page 10
*** Please refer to below pictures for DC jack specifications.
Chapter 2: Installation This is a Mini-ITX form factor motherboard. Before you install the mother- board, study the configuration of your chassis to ensure that the mother- board fits into it. Pre-installation Precautions Take note of the following precautions before you install motherboard com- ponents or change any motherboard settings.
2.1 Installing Memory Modules (DIMM) This motherboard provides two DDR4 (Double Data Rate 4) SO-DIMM slots. Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.
2.2 Expansion Slots (mini-PCIe, PCI Express and M.2 Slots) There is 1 PCI Express slot and 1 mini PCI Express slot on this mother- board. mini-PCIE Slot: MINI_PCIE1 is used for mini PCIE cards. PCIE Slot: The x4 lane width PCIE1 (PCIE 3.0 x8 slot) is used for PCI Express expansion cards.
Page 14
Installing an Expansion Card Step 1. Before installing an expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.
2.3 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illus- tration shows a 3-pin jumper whose pin1 and pin2 are “Short”...
2.4 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! CPU Fan Connector Please connect the CPU fan +12V cable to the connector and...
Page 19
RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating.
Page 20
(USB 2.0 Port (USB2_3) (5VSB Only)) (see p.7, No. 27) Front Panel Audio Header This is an interface for front panel audio cable that allows (9-pin HD_AUDIO1) MIC2_L convenient connection and (see p.7 No. 31) MIC2_R PRESENCE# OUT2_R MIC_RET control of audio devices. J_SENS E OUT2_L OUT_RET...
Page 21
LVDS Connector (40-pin LVDS1) (see p.7 No. 2) *eDP Connector (on the Backside of PCB) EDP1 (40-pin EDP1) Inverter Power Control Wafer (6-pin BLT_PWR1) (see p.7 No. 5) Signal Signal Signal Signal Signal Signal Name Name Name Name Name Name LCD_ LCD_ CON_...
Page 22
Backlight & Amp Volume Control (7-pin BLT_VOL1) (see p.7 No. 17) Signal Signal Signal Signal Signal Signal Signal Name Name Name Name Name Name Name GPIO_ GPIO_ GPIO_ GPIO_ BLT_ PWRDN VOL_ VOL_ BLT_UP * To make the backlight level work properly, please make sure that the interval on button clicks is more than one second.
Chapter 3: UEFI SETUP UTILITY 3.1 Introduction This section explains how to use the UEFI SETUP UTILITY to configure your system. The UEFI chip on the motherboard stores the UEFI SETUP UTILITY. You may run the UEFI SETUP UTILITY when you start up the computer.
3.1.2 Navigation Keys Use < > key or < > key to choose among the selections on the menu bar, and use < > key or < > key to move the cursor up or down to select items, then press <Enter> to get into the sub screen. You can also use the mouse to click your required item.
3.3 Advanced Screen In this section, you may set the configurations for the following items: CPU Configuration, Chipset Configuration, Storage Configuration, Super IO Configuration, ACPI Configuration, USB Configuration and Trusted Com- puting. Setting wrong values in this section may cause the system to malfunction. Instant Flash Instant Flash is a UEFI flash utility embedded in Flash ROM. This convenient UEFI update tool allows you to update system UEFI ®...
3.3.1 CPU Configuration Cool ‘n‘ Quiet Use this item to enable or disable AMD’s Cool ‘n’ Quiet technol- ogy. The default value is [Enabled]. Configuration options: [Enabled] ® and [Disabled]. If you install Windows OS and want to enable this function, please set this item to [Enabled]. Please note that en- abling this function may reduce CPU voltage and memory frequen- cy, and lead to system stability or compatibility issue with some memory modules or power supplies.
3.3.2 Chipset Configuration Above 4G Decoding Enable or disable 64bit capable Devices to be decoded in Above 4G Address Space (only if the system supports 64 bit PCI decod- ing). Primary Graphics Adapter This item will switch the PCI Bus scanning order while searching for video card.
Page 29
eDP Panel BackLight Brightness Use this to adjust eDP panel backlight brightness. You are allowed to adjust this item only when CSM is disabled. Onboard HD Audio Select [Enabled] or [Disabled] for the onboard HD Audio feature. Onboard LAN 1 This allows you to enable or disable the Onboard LAN 1.
3.3.3 Storage Configuration SATA Controller Use this item to enable or disable the SATA Controller feature. SATA Mode Selection Use this to select SATA mode. The default value is [AHCI Mode]. AHCI (Advanced Host Controller Interface) supports NCQ and other new features that will improve SATA disk performance but IDE mode does not have these advantages.
3.3.4 Super IO Configuration COM1 Configuration Use this to set the parameters of COM1. COM2 Configuration Use this to set the parameters of COM2. COM3 Configuration Use this to set the parameters of COM3. Type Select Use this to select COM3 port type: [RS232], [RS422] or [RS485]. COM4 Configuration Use this to set the parameters of COM4.
3.3.5 ACPI Configuration Suspend to RAM Select disable for ACPI suspend type S1. It is recommended to se- lect auto for ACPI S3 power saving. ACPI HPET Table Enable the High Precision Event Timer for better performance. PCIE Devices Power On Use this to enable or disable the PCIE devices to turn on the sys- tem from power-soft-off mode.
3.3.6 USB Configuration Legacy USB Support Use this option to select legacy support for USB devices. There are two configuration options: [Enabled] and [UEFI Setup Only]. The default value is [Enabled]. Please refer to below descriptions for the details of these two options: [Enabled] - Enables support for legacy USB.
3.4 Hardware Health Event Monitoring Screen This section allows you to monitor the status of the hardware on your sys- tem, including the parameters of the CPU temperature, motherboard tem- perature, fan speed and voltage. CPU FAN1 Setting This allows you to set CPU FAN1’s speed. The default value is [Full On].
3.5 Security Screen In this section you may set or change the supervisor/user password for the system. You may also clear the user password. Secure Boot Use this to enable or disable support for Secure Boot.
3.6 Boot Screen This section displays the available devices on your system for you to con- figure the boot settings and the boot priority. Boot From Onboard LAN Use this to enable or disable Boot From Onboard LAN. Setup Prompt Timeout This shows the number of seconds to wait for the setup activation key.
Page 38
CSM (Compatibility Support Module) Enable to launch the Compatibility Support Module. If you are using Windows OS UEFI and all of your devices support UEFI, you may also disable CSM for faster boot speed. Launch PXE OpROM Policy Select UEFI only to run those that support UEFI option ROM only. Select Legacy only to run those that support legacy option ROM only.
3.7 Exit Screen Save Changes and Exit When you select this option the following message, “Save configu- ration changes and exit setup?” will pop out. Select [OK] to save changes and exit the UEFI SETUP UTILITY. Discard Changes and Exit When you select this option the following message, “Discard changes and exit setup?”...
Chapter 4: Software Support 4.1 Install Operating System ® ® This motherboard supports various Microsoft Windows operating systems: Win10. Because motherboard settings and hardware options vary, use the setup proce- dures in this chapter for general reference only. Refer your OS documentation for more information.
4.3 AMD Eyefinity Multidisplay Technology Setting Arrange Eyefinity Display Group 1. Arrange the display in a 4x1 or 2x2 configuration under Windows 10 Display set- ting. 2. Set up AMD Eyefinity with Quick Setup. 3. Click Eyefinity once AMD Radeon Settings opens. 4. Click Quick Setup to automatically create an AMD Eyefinity display group based on the current (default) display configuration.