Residual Risks - Black & Decker BDCDS12 Manual

Safety when sanding paint
@
nt
n.
Whenever possible, use a vacuum extractor for dust col-
u
lection.
Take special care when sanding paint which is possibly
u
lead based and may produce toxic dust:
d.
Do not let children or pregnant women enter the work
u
area.
All persons entering the work area should wear a mask
u
s
specially designed for protection against lead paint dust
and fumes.
Do not eat, drink or smoke in the work area.
u
r
Dispose of dust particles and any other removal debris
u
-
safely.
Safety of others
e
This appliance is not intended for use by persons (includ-
u
ing children) with reduced physical, sensory or mental
n
capabilities, or lack of experience and knowledge, unless
ry
they have been given supervision or instruction concern-
ve"
ing use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
u
play with the appliance.
he
d

Residual risks.

Additional residual risks may arise when using the tool which
e may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or ac-
u
cessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
s.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
a
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Additional safety instructions for batteries
.
Batteries (not supplied)
Never attempt to open for any reason.
u
Do not expose the battery to water.
u
Do not store in locations where the temperature may
u
exceed 40 °C.
Warning! Observe the applicable regulations
for sanding paint. Pay special attention to the
following:
(Original instructions) (Original instructions)
Charge only at ambient temperatures between 10 °C and
u
40 °C.
Charge only using the charger provided with the tool.
u
When disposing of batteries, follow the instructions given
u
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
$
The tool is intend of indoor use only.
Labels on tool
The following pictograms along with the date code are shown
on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Wear a dust mask.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Dust extraction
3. Sanding base
4. Battery
Charging the battery (Not supplied) (fi g. A)
The battery needs to be charged before fi rst use and
whenever it fails to produce suffi cient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
To charge the battery, insert the USB charger (5) into the
u
Battery.
Plug the charger into a suitable power source and switch
u
on.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
ENGLISH ENGLISH ENGLISH
5 5 5