Advertisement
Quick Links
ATC5CPC001 User Manual
Description
- Model : ATC5CPC001
- WLAN : 802.11 a/b/g/n/ac
- Frequency Range : 2400MHz ~ 5845MHz
Features
- Dimension : 22.5mm x 20.0mm x 2.9mm
- Temperature Range : -40℃ ~ +85℃
- Supply Voltage : VBAT 3.2V to 3.6V
- Output Power
WLAN : 17.0dBm(11b 11Mbps), 16dBm(11g 54Mbps, 11n 2.4G MCS7),
15dBm(11a 54Mbps), 14dBm(11n 5G MCS7), 11dBm(11ac MCS9)
- Interface : PCIe(WLAN)
Application
- Automotive (Outdoor Device)
Dimensions
Copyrightⓒ. 2019. All Rights Reserved.
0 / 10
Advertisement
Related Manuals for LG ATC5CPC001
Summary of Contents for LG ATC5CPC001
- Page 1 ATC5CPC001 User Manual Description - Model : ATC5CPC001 - WLAN : 802.11 a/b/g/n/ac - Frequency Range : 2400MHz ~ 5845MHz Features - Dimension : 22.5mm x 20.0mm x 2.9mm - Temperature Range : -40℃ ~ +85℃ - Supply Voltage : VBAT 3.2V to 3.6V - Output Power WLAN : 17.0dBm(11b 11Mbps), 16dBm(11g 54Mbps, 11n 2.4G MCS7),...
-
Page 2: Operating Condition
ATC5CPC001 User Manual Operating condition 1) Recommended operation conditions Parameter Min. Typ. Max. Unit ℃ Operating Temperature Range Supply Voltage : VBATT (3.3V) 1.62 1.98 Supply Voltage : VIO 2.97 3.63 2) Current consumption Parameter Average Max. Unit Stand-by (BT & WLAN) -
Page 3: Boot Up Sequence
ATC5CPC001 User Manual Boot up sequence > 0ms VBAT 100us WL_REG_ON VDDC (on-chip PMU) Max. 12.4msec PCIE_CLKREQ_L PCIE_REFCLK 21.2msec PCIE_PERST_L PCIE_PERST_L D assertion to first config access 6msec 2 / 10 Copyrightⓒ. 2019. All Rights Reserved. -
Page 4: General Features
ATC5CPC001 User Manual General Features • Operation Voltage is 3.3V/1.8V Dual Power Rail • Up to 866 Mbps data rate • Support 2 Antenna port : BT and WLAN ANT1, WLAN ANT2 • Integrated External RF Switch and Internal PA/LNA at 2.4GHz, Internal PA and External RF Switch and LNA at 5GHz •... - Page 5 ATC5CPC001 User Manual General Features BT(v5.0) + 2.4GHz/5GHz WiFi 5 (802.11a/b/g/n/ac) 2x2 MIMO Module Bluetooth(BT5.0 compliant) 1) Bluetooth Key Features • Supports key features of upcoming Bluetooth standards • Fully supports Bluetooth Core Specification version 4.2 + (Enhanced Data Rate) EDR features: -.
- Page 6 ATC5CPC001 User Manual General Features WLAN 1) WLAN RF band & modulation Features • Dual-band 2.4GHz and 5GHz WiFi 5 (802.11a/b/g/n/ac) • Dual-stream up to 866Mbps data rate • Supports 20, 40 and 80MHz channels with optional SGI(256 QAM modulation) •...
- Page 7 ATC5CPC001 User Manual General Features WLAN 3) WLAN PHY features • Programmable data rates from MCS0-9 in 20MHz, 40MHz, and 80MHz channels, as specified in IEEE 802.11ac • Improved performance with 2x2 channel smoothing and spur canceller support • Supports Optional short GI and Green field modes in Tx and Rx •...
-
Page 8: Pin Configuration
ATC5CPC001 User Manual Pin Configuration <TOP View> 7 / 10 Copyrightⓒ. 2019. All Rights Reserved. - Page 9 ATC5CPC001 User Manual Pin Configuration Pin Name Description PCIE_CLK_P PCIE differential clock input positive PCIE_CLK_N PCIE differential clock input negative PCIE_TD_N PCIE Transmitter differential negative PCIE_TD_P PCIE Transmitter differential positive N.C. Not Connected (Reserved) N.C. Not Connected (Reserved) N.C. Not Connected (Reserved) N.C.
- Page 10 ATC5CPC001 User Manual Pin Configuration Pin Name Description BT_PCM_CLK PCM clock, can be master (output) or slave (input) PCM sync signal, can be master (output) or slave BT_PCM_SYNC (input) BT_PCM_IN PCM data input BT_PCM_OUT PCM data output WL_ANT 1 BT/WLAN RF ANT 1 Ground Low power clock input(32.768KHz, 0V ~ 1.8V peak to...
- Page 11 ATC5CPC001 User Manual Pin Configuration Pin Name Description BT, WLAN VDDIO supply voltage.(3.3V or 1.8V) - BT and WLAN should be same power rail SDIO_DIABLE SDIO_DIS : Low : SDIO Enabled, High : SDIO Disabled PCIE_ENABLE PCIE_EN : Low : PCIE Disabled, High : PCIE Enabled...
- Page 12 FCC MODULAR APPROVAL INFORMATION EXAMPLES for Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
- Page 13 This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: YZP-ATC5CPC001”. Information that must be placed in the end user manual: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module.
- Page 14 FCC MODULAR APPROVAL INFORMATION EXAMPLES for Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
- Page 15 2) The transmitter module may not be co-located with any other transmitter or antenna. End product labelling The label for end product must include “Contains FCC ID: YZP-ATC5CPC001, Contains IC: 7414C-ATC5CPC001”. “CAUTION: Exposure to Radio Frequency Radiation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body.
- Page 16 Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer.
- Page 17 Explanation: This module complies with FCC RF radiation exposure limits set forth for an uncontrolled environment, This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body." This module is designed to comply with the FCC statement, FCC ID is: YZP-ATC5CPC001.
- Page 18 784748. Explanation:The host system using this module, should have label in a visible area indicated the following texts: “Contains FCC ID: YZP-ATC5CPC001, Contains IC: 7414C-ATC5CPC001” 2.9 Information on test modes and additional testing requirements5 Additional guidance for testing host products is given in KDB Publication 996369 D04 Module Integration Guide.
- Page 19 2.10 Additional testing, Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.