Specifications - EAW CAM160 Instruction Manual

8. SPECIFICATIONS

Audio Inputs
Input Type
Input Impedance
Output Impedance:
Input Gain Trim Range:
Maximum Input Level:
Nominal Input Level:
Dynamic Range
Phantom Power
Frequency Response:
Total Harmonic Distortion
(Inputs 1-6, and Aux):
EQ
Audio Outputs
Output Type:
Output Impedance:
Nominal Output Level (Both Preamp & Tape Outputs):
Dynamic Range:
Frequency Response (Tape Output):
Total Harmonic Distortion
(Preamp Out):
Power Amplifier
CAM80 Output Power at 1% THD @ 1 kHz:
CAM160 Output Power at 1% THD @ 1 kHz:
Total Harmonic Distortion:
Power Bandwidth (at -1 dBr, all modes):
Signal to Noise ratio:
Protection:
AC Line Input Power
~100 VAC to 240VAC 50/60Hz 110 W (CAM80)
AC Input Low Voltage Detector threshold
Physical Specifications
Height (Excluding Feet):
Width (Overall):
Depth (Rear side of Rack ear to Rear panel, excluding connectors):
CAM80 Weight:
Net
Shipping
CAM160 Weight:
Net
Shipping
Operating Temperature Range
1
– CAM160 / CAM80
Balanced Differential, Unbalanced
30 kΩ (Bal, Line-In)
2.7 kΩ (Bal, Mic-In)
15 kΩ (UnBal, RCA-In)
1 kΩ (UnBal, RCA-Out) (At Direct Outputs)
-3 dB to 40 dB (Mic Input)
-23 dB to 20 dB (Line Input)
+19 dBV
0 dBV
105 dB
24 V
20 Hz - 20 kHz + 1 dB
> 0.1% 20 Hz - 20 kHz @ 0 dBV
Butterworth, ±12 dB fixed at 100 Hz
±12 dB fixed at 10 kHz
Unbalanced / Impedance Balanced
150 Ω / 300 Ω
0 dBV
95 dBV
20 Hz - 20 kHz +/- 1 dB
> 0.04% 20 Hz - 20 kHz @ 0 dBV
80 W @ 100 V
80 W @ 70 V
80 W @ 25 V
80 W @ 4 Ω
160 W @ 100V
160 W @ 70V
160 W @ 25 V
160 W @ 4 Ω
< 0.15%
(100 V, 70 V, 25 V & 4 Ω modes)
40 Hz - 15 kHz (+0 dB –3 dB)
95 dBV
Heatsink Overtemp, DC offset, Short Circuit
220 W (CAM160)
70% of Nominal Line
3.46 inches (88 mm)
19.00 inches (483 mm)
15.00 inches (381 mm)
18.8 lbs. (8.4 kg)
24 lbs. (10.7 kg)
20.8 lbs. (9.3 kg)
26 lbs. (11.6 kg)
-10°C to 45°C, 14°F to 113°F
DISCLAIMER
EAW Commercial continually engages in research related
to product improvement, new materials, and production
methods. Design refinements are introduced into existing
products without notice as a routine expression of that
philosophy. For this reason, any current EAW Commercial
product may differ in some respect from its published
description, but will always equal or exceed the original design
specifications unless otherwise stated.
"EAW Commercial" is a trademark of LOUD Technologies
Inc. All other brand names mentioned are trademarks or
registered trademarks of their respective holders, and are
hereby acknowledged.