Metronic 495407 Manual page 12

the functions of the other buttons.
5 - Check the functions of the other buttons on the remote control. If none of the
buttons function (i.e. the search cannot be stopped at the correct time) or the
majority of the buttons do not function correctly, restart the search (see steps
2 to 4) to find a suitable code. If the majority of the buttons function correctly,
set- up has been successful. Re-press the device button (e.g. TV) to save the
code and to terminate the set-up mode.
3 - Set up by manual search
If setting up with brand name and codes is unsuccessful, you can also use the
"Manual Search" to find the correct code for operating your device.
1 - Switch on the device that you like to control.
2 - Point the remote control at the device. Press and hold the device button (e.g.
TV) for 3 seconds. The LED lights up and the remote is in manual set-up mode,
release the device button now.
3 - Press the "Volume+" button approx. every 1.5 seconds.
4 - As soon as the volume of the device (e.g. TV) changes or the device turns off,
check whether the other buttons on the remote control function correctly .If the
majority of the buttons does not function correctly, press the Volume+ approx.
every 1.5 seconds to initiate the reactive code ( manual search is continued,
see step 3 to 4). If the majority of the buttons on the remote control functions
correctly, save the code by pressing the device button ( e.g. TV) to terminate
the manual search.
Note: The Manual Search is automatically terminated if no entry occurs during
a 30 seconds period.
4 - Display the code
1- Press and hold the device button (TV) and simultaneously press button 1 to
display the thousands of the 4-digit code. Count how often the LED flashes, if
the LED does not flash, the number is zero.
2 - Press and hold the device button (TV), simultaneously press button 2 to
display the hundreds of the 4-digit code, Count how often the LED flashes, if the
LED does not flash, the number is zero.
3 - Press and hold the device button (TV), simultaneously press button 3 to
display the tens of the 4-digit code, Count how often the LED flashes, if the LED
does not flash, the number is zero.
4 - Press and hold the device button (TV), simultaneously press button 4 to
display the ones of the 4-digit code, Count how often the LED flashes.
For example for Code 0169
1- Press TV and 1 LED flashes zero times
2 - Press TV and 2 LED flashes one time
3 - Press TV and 3 LED flashes six times
4 - Press TV and 4 LED flashes nine times
5 - Set up by learning function
We recommend that the batteries of the two controls may be loaded as possible.
1 - Press and hold the button for the device you want to copy (ex.: TV) while the
«Learn» button. When the red LED lights, command and will depend learning (in this
case to control TV).
2 - Press and release the button universal remote we want to record (ex.: POWER),
the LED flashes (if no button is pressed within 14 seconds, the remote will exit the
learning mode automatically).
3 - Press a button on the remote copy (ex.: POWER) once the LED flashes 3 times
faster then stops blinking maintaining the steady light, it means you have accepted
the new code for that button and you can start record another command button (if no
button is pressed in 14 seconds the controller will automatically learning function, and
will need to start from step 1).
4 - Repeat steps 2 to 4 for learning from other codes from the original remote.
5 - When all buttons you wish to copy, press the «Learn» button to record and save
changes to the universal command and exit the function completes learning.
6 - Press TV + 6 button and wait until the LED blinks three times. This will erase all
codes that you have learned from all devices.
Note:
Orient the original remote infrared transmitter to the receiver looking infrared universal
remote leaving about 30 mm. Keep the two knobs on the same line to make the
technical support: soporte@metronic.com · * Device code list available at: www.metronic.tv
EN
3