Table of Contents
Advertisement
3.6 TEST FUNCTIONS
TOP PREVIOUS NEXT
The codes listed below can be used to perform simple checks of some of the unit's functions. When
complaints are received from customers, they provide an effective tool for identifying the locations
and causes of malfunctions.
Test Mode
Type of
Mode
MOTOR TEST
Service
Mode
MODEM TEST
Service
Mode
ROM CHECK
Service
Mode
SCAN CHECK
Service
Mode
LCD CHECK
Service
Mode
DTMF SINGLE TEST
Service
Mode
LED CHECK
Service
Mode
KEY CHECK
Service
Mode
FACTORY SET
Service
Mode
PRINT TEST PATTERN
Service
Mode
DIGITAL
Service
SPEAKERPHONE RX &
Mode
TX CHECK
SENSOR CHECK & VOX
Service
CHECK
Mode
file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN...
Code
Operation after code
input
"5" "5" "6"
Rotates the transmission and reception motor to check the operation of the motor.
13: FAX TX / Reading memory
14: Document feed
23: Recording paper is fed
33:List / FAX RX print, pull back recording paper
43: Copy
START
05: Recording paper feed
(Test a recording paper feeding operation by shifting from 23 to 33).
Press
"5" "5" "4"
Telephone line circuit is connected automatically, output the following signals on the
circuit line.
1) OFF 2)14400bps 3)12000bps 4) 9600bps(U17) 5)7200bps(U17) 6)9600bps 7)7200bps
START
8) 4800bps 9) 2400bps 10) 300bps 11) 2100Hz 12)1100Hz
"5" "5" "1"
Indicates the version and checks the sum of the ROM.
START
"5" "5" "5"
Turns on the LEDs of the CIS and operates the read systems.
START
"5" "5" "8"
Checks the LCD indication.
Illuminates all the dots to check if they are normal.
START
"5" "5" "2"
Outputs the DTMF as single tones. Used to check the frequencies of the individual DTMF
tones. Refer to
1....ON
2....OFF
"5" "5" "7"
All LEDs above the operation panel board flash on and off, or are illuminated.
START
"5" "6" "1"
Checks the button operation.
Indicates the button code on the LCD while the button is pressed. Refer to
START (any key)
CODE TABLE
"5" "5" "0"
Clears the memory where the users can store data.
START
"8" "5" "2"
Prints out the test pattern.
Used mainly at the factory to test the print quality.
START
You can select 1~4. (See
"8" "4" "1"
Please refer to
SPEAKERPHONE
"8" "1" "5"
If you enter this mode and operate sensor levers with your hands, the LCD display of the
related sensor (or switch) turns ON / OFF. Also, when copying a document, the related
sensor willturn ON / OFF. ( Do, Sn, Co, Pt, Vx)
For each sensor's operation, refer to
[Do Sn Co Pt Vx] : LCD DISPLAY
Do: Document set sensor
:Paper inserted. Turns on when a document is inserted.
Sn: Read position sensor.
:At the read position, turns on when the front cover is opened and the sensor lever is
pressed directory.
START
Co: Cover open sensor / Film end sensor
:Cover open of don't set the film. Turns on and off when the front cover is opened and
closed.
Pt: Paper top sensor
:Sensor on Turns on when the front cover is opened and the sensor lever is pressed
directly.
Vx: Vox signal
http://servis-manual.com/
Function
button to quit.
DTMF SINGLE TONE TRANSMIT SELECTION
().
PRINT TEST PATTERN
())
DIGITAL SPEAKERPHONE
()
SENSORS AND SWITCHES
Stránka č. 1 z 2
().
BUTTON
().
27. 10. 2004
Advertisement
Table of Contents
