Unpacking & Assembly - Husqvarna TF545P Operator's Manual

Note: In the constant desire to improve
the products, the manufacturer states
that the whole of this manual is not
contractual and reserves the right to
modify the specifications of
.
machines without notice
Unpacking
1 1 •
WARNING:
Take care not to cut the cables
or scratch the machine's paint-
work when cutting the edges of
the case.
Ref. Contents of the case
Engine Parts
A
Sub Holder 1st
B
Holder Main Comp
C
Lower Tidy Cover
D
Drag Bar
E
Tine Cover
F
Tine Cover Bracket FR.
G
Lever Shifting
H
Blade s
I
J Wheel
Connector Joint
K
Extionsion Cover
L
Side Cover
M
Locking Handle
N
O
Tine Cover Bracket RR.
P
Rubber Cable Holder
Q
Connecting Plate
R
Hardware Bag Tines only
S
Hardware Bag
T
Tool
Bag
Filling with engine oil
and checking the level
2 1 •
Filling with gearbox
2 2 •
Topping up the petrol
2 3 •
Recommend to USE
Octane Value over 90
Add oil to the air filter
2 4 •
Filling the oil to Oil Level
All manuals and user guides at all-guides.com
UNPACKING ASSEMBLY
/
1 2 •
the
WARNING:
Inappropriate assembly of this
rotary
severe injuries. Ensure that
you follow all the instructions
carefully.
1 2 3 Fitting the tine blades .
4 5 • 6 Illustrations only shows asse-
mbly of the tin blades on the
right side.
Make sure that sharp edges
face one side on both Right
and Left side tines.
Note:Please pay attention to
distinguish the Sub Holder 1st
and Sub Holder 2nd.
7
Fitting the connecting joint.
8
Fitting the drag bar.
9
Fitting the handle bar.
10 11
Adjusting the position of the
handle bar.
12
the
Fitting
Turn to proper side and fasten the
bolt.
13 14
Fitting
.
1 Tidy the cables
2 Put on the .
.
3 Put on the cover,and fasten with
bolt.
15 16
Fitting
17
18
Do not tighten the bolt immediately
after installed. Install all 4 bolts and
19
nuts first, then tighten one by one.
20
the
Fitting
21
PTO assemble for accessories.
START ING THE MACHINE
Open the
2 5 •
2 6 •
oil
Throttle control
2 7 •
Set the
2 8 •
Assembling
Note Any dismantling operation must
only be performed by a
tiller could cause
workshop
1 3
10
11
12
13
14
1 4 1 4
clutch control.
1 5
the
lower tidy cover.
,
rubber holder properly,
the
tine cover.
shifting lever.
fuel tap
2 9
Set the choke
in position A 2 10
:
Put the lever
to
on off switch
/
to
ON
2 1
•
WARNING:
After assembling the machine
completely, tighten all the bolts
and screws with moderation:
.
do not overtighten
:
H
usqvarna
.
Description
• of the components
1
-Engine
2 - Tine cover
3 -
Handle
4
-
Extension cover
5
- Blade
s
6
- Drag bar
7 Upper tidy cover
-
8
-Lever shifting
9
-Bumper
-Clutch control
-
Throttle ontrol c
-
Reverse control
-
Side cover
-
Lower tidy cover
Type plate
• •
Transport wheel
•
Change the blades with wheels when
transporting
Shifting lever
•
Put the lever to gear
Pull the recoil start
•
handle
WARNING:
When the machine starts
remain within the safety zone
Set the choke
in position B
• 1
N .
,
.