Sony PCS-C150 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Camcorder
  5. PCS-C150
  6. Service manual
Sony PCS-C150 Service Manual

Sony PCS-C150 Service Manual

Color video camera
Hide thumbs Also See for PCS-C150:
Table of Contents

Advertisement

Quick Links

Download this manual
PCS-C150/C150P
Sony Corporation
9-928-130-11
Information Technology Company
99E09008-1
Printed in Japan C1999. 5
Published by VAIO Custormer Link
– 80 –
PCS-C150/C150P
SERVICE MANUAL
SPECIFICATIONS
System
Video signal
PCS-C150 : NTSC standards
PCS-C150P : PAL Color, CCIR
standards
Picture element
1/3 inch color CCD
(Total picture element number :
PCS-C150 : Approx. 410,000
PCS-C150P : Approx. 470,000)
(Effective picture element
number :
PCS-C150 : Approx. 380,000
PCS-C150P : Approx. 440,000)
Lens
Electromotion twelve fold zoom
lens
f=5.4 to 64.8mm, F1.8 to F2.7
Horizontal angle : 4.4º to 48.8º
Point-blank range
WIDE end : 10mm
TELE end : 800mm
Minimum illumination 7 lux (F1.8)/with 50IRE
Illumination range
7 to 100,000 lux
Shutter speed
PCS-C150 : 1/60 to 1/10,000 (VISCA
control)
PCS-C150P : 1/50 to 1/10,000 (VISCA
control)
Gain selector
Automatic/manual
Horizontal resolution
NTSC : 460 TV
PAL : 450 TV
Video S/N
48 dB
Pan/tilt action
Horizontal : 100º, Vertical : 25º
9-928-130-11
PCS-C150 (NTSC)
PCS-C150P (PAL)
Input/output terminals
Processor terminal
D-sub 15 pin
Output control terminal 8 pin mini DIN
General
Input voltage
DC 12 to 14 V
Power consumption
11 W (Refference value)
Operating temperature 0º to 40º (32º to 104ºF)
Storage temperature
– 20º to 60º (– 4º to 140ºF)
Approx 142 × 109 × 162 mm
Dimensions
(w/h/d)
Mass
Approx. 1,200 g (42.3 oz.)
COLOR VIDEO CAMERA

Advertisement

Table of Contents
loading

Related Manuals for Sony PCS-C150

Summary of Contents for Sony PCS-C150

  • Page 1 WIDE end : 10mm TELE end : 800mm Minimum illumination 7 lux (F1.8)/with 50IRE Illumination range 7 to 100,000 lux Shutter speed PCS-C150 : 1/60 to 1/10,000 (VISCA control) PCS-C150P : 1/50 to 1/10,000 (VISCA control) Gain selector Automatic/manual Horizontal resolution...
  • Page 2 COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. RE- PLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

  • Page 3: Table Of Contents

    5. PRINTED WIRING BOARDS 7-3-5. Command Execution Stop ........7-3 5-1. Circuit Boards Location ..........5-1 7-4. PCS-C150/C150P Setting Commands (Network setting) 5-2. Printed Wiring Boards 7-4-1. VISCA Network Management Commands ..7-4 • This Note is Common for Printed Wiring Boards ..... 5-2 7-4-2.
  • Page 4 8. REPAIR PARTS LIST 8-1. Exploded Views 8-1-1. Camera Cabinet Section ........... 8-1 8-1-2. Pan Base Section ............8-2 8-1-3. Tilt Base Section ............8-3 8-1-4. Lens Section ............. 8-5 8-2. Electrical Parts List • AT-21A (A) Board ............8-6 •...

  • Page 5: General

    PCS-C150/C150P SECTION 1 GENERAL General Precautions Locations of Controls • After operating the unit with an AC power adaptor, disconnect the AC power adaptor from the wall outlet if the set is not to be used for an ex- tended period of time.

  • Page 6: Connections

    Use Reset command to reset the pan/tilt position. has plug of EIAJ type 4 (not supplied). Do not use any other AC power adaptor. Flashes. Polarity of the plug PCS-C150/C150P is controlled by VISCA communication. Refer to VISCA COMMAND LIST.

  • Page 7: Disassembly

    PCS-C150/C150P SECTION 2 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 2-1. CAMERA CABINET (UPPER) 5 M 2x4 2 M 2x4 6 camera cabinet (upper) 1 M 2x4 4 camera cabinet (front) assy 3 claw 2-2.

  • Page 8: Main Block

    2-3. MAIN BLOCK 3 RM-77A(A) board 1 PTP 2.6x8 2 CN381 6 PTP 2.6x8 4 PTP 2.6x8 5 ground plate (P) 7 main block 2-4. ID-11A (A) BOARD 5 M 2x2.2 6 M 2x2.2 3 CN104 2 CN109 1 CN102 8 ID-11A (A) board 4 CN103 7 CN110...

  • Page 9: Pan Base Assy

    2-5. PAN BASE ASSY 1 P 2x6 3 flexible flat cable 4 pan base ASSY 2 timing belt 2-6. LI-55A (A) BOARD 1 M 2x4 2 retainer 4 P 3x4 3 LI-55A(A) board 5 stepping motor (PAN)

  • Page 10: Pan Cabinet

    2-7. PAN CABINET 3 pan cabinet (front) 1 M 2x4 4 tapping screw 2 M 2x4 5 Extend the pan cabinet (rear) out and remove the cabinet. 2-8. CCD LENS ASSY 3 CN105 PCS-C150P only 5 CCD lens ASSY 4 CN893 1 M 2x4 2 M 2x4...

  • Page 11: Camera Cabinet (Lower)

    2-9. CAMERA CABINET (LOWER) 3 Turn the tilt bearing in the direction of the arrow and remove the bearing. 2 type-E stop ring 3.0 4 Turn the tilt bearing in the 5 flexible flat cable direction of the arrow and remove the bearing.

  • Page 12: Li-59A (A) Board

    2-11. LI-59A (A) BOARD 2 M 2x3 1 CN351 3 LI-59A(A) 5 M 2x3 6 LI-52A(A) 4 CN341 2-12. LD-84A (A)/84A (B) BOARD 5 LD-84A(A)/84A(B) board 1 M 2x3 2 CN702 3 CN701 PCS-C150P only 4 Sheet,electrostatic...

  • Page 13: A)/179 (B) Board

    2-13. VC-179 (A)/179 (B) BOARD 8 CN504 7 CN401 9 VC-179(A)/179 (B) board 6 M 2x3 5 M 2x3 3 CN894 1 M 2x3 2 CN845 4 AT-21A(A) board 2-14. RS-67A (A)/LB-47A (A) BOARD 5 claw 1 claw 2 CN403 7 RS-67A(A) board 3 LB-47A(A) board 4 M 2x3...

  • Page 14: A) Board

    2-15. MD-68 (A) BOARD 2-17. CD-154A (A) BOARD 3 MD-68 (A) board 1 BTP 2x12 2 M 2x3 2 CD-154A(A) board 1 M 2x3 2-16. LENS BLOCK 2-18. CCD FITTING ADAPTOR (H) 1 claw 3 CCD fitting adaptor (H) 2 claw 1 BTP 2x5 4 optical filter block 5 seal rubber (3)

  • Page 15: Ld-84A(A)/84A(B) Board

    PCS-C150/C150P SECTION 5 PRINTED WIRING BOARDS 5-1. CIRCUIT BOARDS LOCATION LI-59 A(A) board ID-11A(A) board LI-52A(A) board RM-77A(A) board LI-55A(A) board LB-47A(A) board AT-21A(A) board RS-67A(A) board MD-68 (A) board CD-154A(A) board VC-179 (A)/179 (B) board LD-84A(A)/84A(B) board...

  • Page 16: Printed Wiring Boards

    PCS-C150/C150P 5-2. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS. • For printed wiring boards. • Through hole is omitted. • Pattern is omitted. CD-154A (A) (CCD IMAGER) PRINTED WIRING BOARD – Ref. No. CD-154A (A) BOARD : 1,000 series –...
  • Page 17 PCS-C150/C150P VC-179 (A)/179 (B) (CAMERA) PRINTED WIRING BOARD – Ref. No. VC-179 (A)/179 (B) BOARD : 1,000 series – VC-179 (A)/179 (B) BOARD D001 D302 D401 D402 D403 D404 D406 IC001 IC302 IC401 IC402 IC403 IC404 IC405 IC406 IC407 IC501...
  • Page 18 PCS-C150/C150P MD-68 (A) (MODE CONTROL) RS-67A (A) (BACK UP) PRINTED WIRING BOARDS – Ref. MD-68 (A) BOARD : 1,000 series, RS-67A (A) BOARD : 2,000 series – RS-67A (A) BOARD D401 MD-68 (A) D402 BOARD D403 D101 D404 D104 D405...
  • Page 19 PCS-C150/C150P ID-11A (A)/11A (A) ID-11A (A) (MOTOR DRIVE, INPUT/OUTPUT) PRINTED WIRING BOARDS BOARD – Ref. No. ID-11A (A) BOARD : 2,000 series D102 D103 D104 D105 D109 D110 D112 D113 D114 D115 D116 D117 D118 D119 D154 D157 D159 D160...
  • Page 20 PCS-C150/C150P AT-21A (A) (VIDEO PROCESS, MAIN CONTROL) LI-52A (A) (TILT END SENSOR) LI-59A (A) (TILT R SENSOR) LI-55A (A) (PAN R SENSOR) PRINTED WIRING BOARDS – Ref. No. AT-21A (A) BOARD : 1,000 series, LI-52A (A) BOARD : 2,000 series, LI-55A (A) BOARD : 2,000 series, LI-59A (A) BOARD : 2,000 series –...
  • Page 21 PCS-C150/C150P LD-84A (A)/84A (B) (LENS DRIVE) PRINTED WIRING BOARD – Ref. No. LD-84A (A)/84A (B) BOARD : 2,000 series – LD-84 A (A)/84A (B) BOARD IC701 IC702 IC703 IC704 IC705 Q701 Q702 LENS DRIVE 5-11 LD-84A (A)/84A (B)
  • Page 22 RM-77A (A) (REMOCON RECEIVING OPTICAL), LB-47A (A) (BATTERY) PRINTED WIRING BOARD – Ref. No. RM-77A BOARD : 1,000 series, LB-47A (A) BOARD : 1,000 series – 5-12 E...

  • Page 23: A)/179 (B) Board

    PCS-C150/C150P SECTION 6 ADJUSTMENTS 6-1. PREPARATION FOR ADJUSTMENT 6-1-1. List of Servicing Jigs • Oscilloscope • Regulated power supply • Audio generator • Audio level meter • Color monitor • Vectorscope • Desk-top calculator • Digital voltmeter Ref. No. Name Part No.

  • Page 24: Preparations

    J-10 J-11 J-12 J-13 J-14 J-15 Fig. 6-1. 6-1-2. Preparations Note: When adjusting only, it is not needed to remove the camera block from the pan tilt mechanism chassis. 1.5m The adjustments can be performed only by removing the camera cabinet. 1) Connect the equipments for adjusting as shown in Fig.
  • Page 25 Fig. 6-3 (1).
  • Page 26 Fig. 6-3 (2).

  • Page 27: Precautions

    6-1-3. Precautions 2. Subject 1. Adjusting Procedure 1) Color bar chart (Standard picture frame) Adjust in the given order. Adjust the picture frame as shown in Fig. 6-4. if adjustments are performed using the color bar chart. (Standard picture frame) 2) White pattern (Standard picture frame) Remove the color bar chart from the pattern box, and so that the white pattern will be displayed.

  • Page 28: Adjusting Remote Commander

    6-1-4. Adjusting Remote Commander LCD Display of the Adjusting Remote Commander Use the adjusting remote commander to change the coefficient of the digital signal processing or the EVR data. The adjusting remote commander uses the remote commander sig- nal line (ECCP) to perform the bidirectional communication with the camera microprocessor.

  • Page 29: Page D Address List

    71 to FF. This has no relation to the adjustment. Note 4: No mark : PCS-C150 series : PCS-C150P series Note 5: * PCS-C150 (NTSC): 04 (Only Camera Block 00) PCS-C150P (PAL): 05 (Only Camera Block 01) Caution: When adjusting the camera with only the camera block mounted, use the data for Only Camera Block.
  • Page 30 Adjustment data Adjustment data Address Address Initial value Memo column Initial value Memo column 18 (1C) 14 (18) 71 to FF Table. 6-2 (3). Table. 6-2 (2).

  • Page 31: Page F Address List

    Note 3: In some cases, data have been input to the page F addresses C0 to EF. This has no relation to the adjustments. Note 4: No mark : PCS-C150 series : PCS-C150P series 5E (71) 77 (8A)
  • Page 32 Adjustment data Adjustment data Address Address Initial value Memo column Initial value Memo column 28 (2C) 28 (2C) 26 (42) 26 (42) 46 (4A) 46 (4A) 04 (00) 04 (00) 04 (00) 04 (00) 00 (02) 00 (02) E8 (D8) E8 (D8) 30 (28) 30 (28)
  • Page 33 Adjustment data Adjustment data Address Address Initial value Memo column Initial value Memo column 44 (87) 44 (87) 3D (39) 3D (39) 3D (39) 3D (39) 12 (32) 12 (32) 4B (4A) 4B (4A) 23 (27) 23 (27) 60 (6C) 60 (6C) 6B (6C) 6B (6C)

  • Page 34: Address List

    Note 3: In some case, data have been input to the page 5 address A0 to FF. This has no relation to the adjustment. Note 4: No mark : PCS-C150 series 12 (10) 12 (10) : PCS-C150P series...
  • Page 35 Adjustment data Adjustment data Address Address Initial value Memo column Initial value Memo column 14 (17) 14 (17) 05 (04) 05 (04) 18 (1C) 18 (1C) 14 (18) 14 (18) 07 (08) 07 (08) 07 (08) 07 (08) 0C (0A) 0C (0A) 0C (0A) 0C (0A)

  • Page 36: Data Processing

    6-1-8. Data Processing The calculation of the adjusting remote commander display data (hexadecimal notation) is required for obtaining the adjustment data of some adjustment itemes. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.

  • Page 37: Camera System Adjustment

    6-2. CAMERA SYSTEM ADJUSTMENT Note 2: * PCS-C150: 00 PCS-C150P: 01 6-2-1. Power Supply Voltage Check After the camera adjustment, input the data given below. (VC-179 (A)/179 (B) board) PCS-C150: 04 Subject Option PCS-C150P: 05 Measuring instrument Digital voltmeter (Refer to 6-2-20. Page D Data Modification 2.) MT5V check 6-2-4.

  • Page 38: 28 Mhz Original Oscillation Adjustment

    6-2-6. 28 MHz Original Oscillation Adjustment 6-2-8. VRG Adjustment (VC-179 (A)/179 (B) board) Set the CCD imager V RG voltage to the voltage specified for the Adjust the 28 MHz oscillation of the synchronization clock. imager. If the oscillation is not 28 MHz, the period will be inaccurate or the image will not be in color.

  • Page 39: Flange Back Adjustment

    6-2-10. Flange Back Check 6-2-9. Flange Back Adjustment The flange back adjustment for the inner focus lens is performed automatically. Siemens star Subject (2m from the front of the lens) Chart for flange back adjustment Measurement Point TV monitor 2000 ± 5mm from the front side Measuring Instrument Subject of the lens...

  • Page 40: Hall Adjustment

    15)Convert X1’ to hexadecimal notation, and obtain X1. 6-2-11. Hall Adjustment (Round off to one decimal place) To eliminate the differences in the outputs of the hall element 16)Set data: X1 to page: F, address: 06, and press the PAUSE but- attached to the iris for detecting the position of the lens iris, adjust ton of the adjusting remote commander.

  • Page 41: Picture Frame Setting

    Check on the oscilloscope 6-2-12. Picture Frame Setting 1. Horizontal period Subject Color bar chart standard picture frame A = B C = D Measurement Point VIDEO OUT terminal Measuring Instrument Oscilloscope and TV monitor + 0.1 Specified Value A=B, C=D, t=0 msec –...

  • Page 42: Color Reproduction Adjustment

    Adjustment Address 08, 09, 0A, 0B All color luminance points should Specified Value settle within each color reproduction For PCS-C150 frame. Burst position Adjusting method: 1) Set data: 01 to page: 6, address: 00. 2) Set data: 00 to page: 6, address: 03.

  • Page 43: Iris In/Out Adjustment

    Measurement Point Lower 2 digits of the date of the page Adjustment Page Measuring Instrument A displayed Adjustment Address Adjustment Page PCS-C150 Adjustment Address 13, 14 A=450mV Specified Value PCS-C150P Adjusting method: 1) Set data: 01 to page: 6, address: 00.

  • Page 44: Auto White Balance Standard Data Input

    6-2-16. Auto White Balance Standard Data Input 6-2-17. Auto White Balance Adjustment Adjust to the proper auto white balance output data. Subject White pattern standard picture frame If it is not correct, auto white balance and color reproducibility will be poor. Adjustment Page Adjustment Address 0C, 0D, 0E, 0F...

  • Page 45: White Balance Check

    6-2-18. White Balance Check 3 mm Subject White pattern standard picture frame Filter C14 for color temperature Filter correction 3 mm ND filter 1.0 and 0.3 1.5 mm Measurement Point VIDEO OUT terminal 0.5 mm Measuring Instrument Vectorscope Specified Value 6-14 A to C Fig.

  • Page 46: Page D Data Modification 2

    After the camera adjustment, change the data of page D and ad- 6-3-1. Pan Tilter Operation Check dress 01 to the following: Checking method: PCS-C150 (NTSC) Data: 04 1) Use VISCA to send the commands to move the pan tilter PCS-C150P (PAL) Data: 05 horizontally and vertically.

  • Page 47: Visca Command List

    Fig. 7-1. VISCA Network PCS-C150/C150P has a VISCA IN port and a VISCA OUT port. As viewed from the outside, both the VISCA IN and VISCA OUT ports have the connector pin layout shown in Fig. 7-2. During control by a computer, set the PCS-C150/C150P DTR input ( the computer’s S output ) high.

  • Page 48: Pcs-C150/C150P-Visca Connection

    1 is 81H ( hexadecimal ). A packet sent to PCS-C150/C150P at Address 2 has a header of 82H. In the tables after pages 7-6, the header is listed as 8X. Insert the PCS- C150/C150P address in place of the X. The header for a packet sent in response from the PCS-C150/C150P at Address 1 is 90H. For a response packet form the PCS-C150/C150P at Address 2, the header is A0H.

  • Page 49: Commands And Inquiries

    PCS-C150/C150P before sending the next message. However, in order to provide higher level usage, the PCS-C150/C150P has two com- mand buffers (memories) so it can receive up to two commands (including the one it is executing) at a time. When the PCS-C150/C150P receives a command, it sets the socket number in the ACK message to tell the controller which command buffer is used.

  • Page 50: Pcs-C150/C150P Setting Commands (Network Setting)

    Network Change X0 38 FF X = 9 to F : PCS-C150/C150P address + 8 7-4-2. VISCA Interface Commands IF_Clear: Clears the command buffers in the PCS-C150/C150P and stops the instruction being executed. Command Packet Reply Packet IF_Clear 8X 01 00 01 FF...
  • Page 51 CAM_AE 1) Full auto When the automatic exposure (AE) mode is set, the auto-iris, AGC (auto-gain), 1/60 sec shutter (PCS-C150P is 1/50 sec shutter) will operate. When the power supply is turned on with the lithium backup off, the automatic exposure mode will be set. 2) Manual When the manual mode is set, iris, gain and shutter will be set separately.

  • Page 52: Pcs-C150/C150P Commands

    7-5. PCS-C150/C150P Commands Command Set Command VISCA Packet Comments CAM_Power 8x 01 04 00 02 FF 8x 01 04 00 03 FF CAM_Zoom Stop 8x 01 04 07 00 FF Tele (Standard) 8x 01 04 07 02 FF Wide (Standard)
  • Page 53 Command Set Command VISCA Packet Comments CAM_Iris Reset 8x 01 04 0B 00 FF 8x 01 04 0B 02 FF Down 8x 01 04 0B 03 FF Direct 8x 01 04 4B 0Z 0Z 0Z 0Z FF ZZZZ : 0000 (CLOSE) to 0011 (F1.8) CAM_Gain Reset 8x 01 04 0C 00 FF...
  • Page 54 Command Set Command VISCA Packet Comments Pan-tiltDrive 8x 01 06 01 VV WW 03 01 FF VV : pan speed 01 to 18 (01 to 1C for D31) Down 8x 01 06 01 VV WW 03 02 FF WW : tilt speed 01 to 14 (01 to 18 for D31) Left 8x 01 06 01 VV WW 01 03 FF Right...
  • Page 55 Command Set Command VISCA Packet Comments AT_Offset 8x 01 07 05 02 FF 8x 01 07 05 03 FF On/Off 8x 01 07 05 10 FF AT/MD_Start/Stop Start/Stop 8x 01 07 06 10 FF AT_Chase Chase1 8x 01 07 07 00 FF Chase2 8x 01 07 07 01 FF Chase3...
  • Page 56 7-6. PCS-C150/C150P Inquiry Commands Inquiry Packet Inq Packet Reply Description CAM_PowerInq 8x 09 04 00 FF Y0 50 02 FF Y0 50 03 FF CAM_ZoomPosInq 8x 09 04 47 FF Y0 50 0Z 0Z 0Z 0Z FF ZZZZ : 0000 to 03FF...
  • Page 57 Inquiry Packet Inq Packet Reply Description DatascreenInq 8x 09 06 06 FF Y0 50 02 FF Y0 50 03 FF AT/MD_ModeInq 8x 09 07 22 FF Y0 50 00 FF Normal mode Y0 50 01 FF AT mode Y0 50 02 FF MD mode AT_ModeInq 8x 09 07 23 FF...

  • Page 58: Code List

    7-7. Code List 7-7-1. Code list for Shutter, Iris, Gain and Wide con lens Code Shutter (1/X sec.) Iris Gain (dB) Code Wide Con lens No. 60 (D31 : 50) CLOSE – 3 0.85 0.75 125 (D31 : 120) 0.65 F9.6 Table.

  • Page 59: Code List For Pan/Tilter Status, At Mode Status And Md Mode Status

    7-7-2. Code list for Pan/Tilter status, AT mode status and MD mode status Code list for Pan/Tilter status 0 - - - - - - - 0 - - - - - - 1 Pan left end 0 - - - - - - - 0 - - - - - 1 -...

  • Page 60: Visca Communications Examples

    The 3rd byte of the reply to an address message is the number of connected devices plus 1. In this example, three devices are connected, so this byte is 04. Setting the focus position of the first PCS-C150/C150P to 0105H. Sending...
  • Page 61 PCS-C150/C150P SECTION 8 REPAIR PARTS LIST 8-1. EXPLODED VIEWS NOTE: • The mechanical parts with no reference • -XX and -X mean standardized parts, so number in the exploded views are not supplied. they may have some difference from the •...
  • Page 62 8-1-2. PAN BASE SECTION not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-971-346-01 BELT, TIMING * 70 3-202-552-01 PANEL, REAR 3-972-548-01 PLATE, PAN SLIDER 3-971-634-01 FOOT (REAR) 3-971-354-01 PULLEY, TENSION 3-719-381-01 SCREW (M2X4) * 54 X-3946-396-1 ARM ASSY, PULLEY 3-713-786-91 SCREW (M2X3)
  • Page 63 8-1-3. TILT BASE SECTION not supplied not supplied not supplied not supplied not supplied not supplied...
  • Page 64 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-971-362-02 CABINET (REAR), PAN 3-971-334-01 GEAR, TILT DECELERATION 3-945-884-31 SCREW 3-701-439-11 WASHER * 103 X-3946-397-1 RETAINER ASSY * 129 3-971-377-02 WING, PAN SENSOR 3-971-368-01 SPRING, COMPRESSION 3-971-356-02 GEAR, WORM 3-971-372-01 DISK 3-971-335-01 SHAFT, TILT WORM 3-971-374-01 REINFORCEMENT, ROTARY...
  • Page 65 8-1-4. LENS SECTION not supplied not supplied(C150P) not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 151 A-8056-258-A AT-21A (A) MOUNT A-8045-279-A CCD BLOCK ASSY (AUTO) (C150P) * 152 A-7072-759-A VC-179 (A) MOUNT (C150) * 165 A-8056-249-A CD-154A (A) MOUNTED PWB * 152...
  • Page 66 AT-21A (A) CD-154A (A) 8-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since When indicating parts by reference the parts list may be different from the they are seldom required for routine service. number, please include the board.
  • Page 67 CD-154A (A) ID-11A (A) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > D116 8-719-050-90 DIODE MA736-TX D117 8-719-050-90 DIODE MA736-TX R892 1-216-829-11 RES,CHIP 4.7K 1/16W D118 8-719-050-90 DIODE MA736-TX R893 1-216-840-11 RES,CHIP 1/16W D119 8-719-050-90 DIODE MA736-TX R894...
  • Page 68 ID-11A (A) LB-47A (A) LD-84A (A)/84A (B) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > R241 1-216-835-11 RES,CHIP 1/16W R253 1-216-822-11 RES,CHIP 1.2K 1/16W Q101 8-729-026-52 TRANSISTOR 2SA1576A-T106-QR R257 1-216-839-11 RES,CHIP 1/16W Q102 8-729-029-14 TRANSISTOR DTC144EUA-T106 R258 1-216-833-91 RES,CHIP...
  • Page 69 LI-52A (A) LD-84A (A)/84A (B) LI-55A (A) LI-59A (A) MD-68 (A) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CN702 1-691-539-11 CONNECTOR, BOARD TO BOARD 30P * 1-674-602-11 PWB, LI-52A *********** < IC > (Ref. No. 2,000 series) IC701 8-759-349-19 IC NJM3414AM-TE2 <...
  • Page 70 MD-68 (A) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C115 1-162-968-11 CERAMIC CHIP 0.0047uF 10% < RESISTOR > C116 1-162-974-11 CERAMIC CHIP 0.01uF R101 1-216-295-91 SHORT C117 1-164-361-11 CERAMIC CHIP 0.047uF R108 1-216-845-11 RES,CHIP 100K 1/16W C118 1-164-361-11 CERAMIC CHIP...
  • Page 71 MD-68 (A) RM-77A RS-67A (A) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R170 1-216-821-11 RES,CHIP 1/16W < RESISTOR > R172 1-216-821-11 RES,CHIP 1/16W R173 1-216-821-11 RES,CHIP 1/16W R382 1-216-821-11 RES, CHIP 1/16W R174 1-216-821-11 RES,CHIP 1/16W R383 1-216-805-11 RES, CHIP...
  • Page 72 VC-179 (A)/179 (B) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * A-7072-759-A VC-179 (A) MOUNT (C150) C402 1-163-021-91 CERAMIC CHIP 0.01uF * A-7072-790-A VC-179 (B) MOUNT (C150P) C403 1-164-346-11 CERAMIC CHIP C404 1-164-156-11 CERAMIC CHIP 0.1uF *********************** (Ref.
  • Page 73 VC-179 (A)/179 (B) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C531 1-162-974-11 CERAMIC CHIP 0.01uF L313 1-412-028-11 INDUCTOR CHIP 4.7uH L315 1-412-028-11 INDUCTOR CHIP 4.7uH C532 1-135-181-21 TANTAL. CHIP 4.7uF 6.3V L401 1-412-058-11 INDUCTOR CHIP 10uH <...
  • Page 74 VC-179 (A)/179 (B) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R323 1-218-879-11 RES,CHIP 0.50% 1/16W R515 1-216-863-11 RES,CHIP 3.3M 1/16W R325 1-218-875-11 RES,CHIP 0.50% 1/16W (C150P) R326 1-218-873-11 RES,CHIP 0.50% 1/16W R516 1-216-833-91 RES,CHIP 1/16W R327 1-218-881-11 RES,CHIP 0.50% 1/16W...

This manual is also suitable for:

Pcs-c150p

Table of Contents