Page 89 Instrument Panel Overview ..4-4 Steering Wheel Adjustment . . . 4-6 Steering Wheel Controls ..4-6 Heated Steering Wheel ..4-7 Horn ......4-7 Windshield Wiper/Washer .
Page 90 Driver Information Center (DIC) ....4-26 Head-Up Display (HUD) ..4-29 Vehicle Messages ... 4-33 Battery Voltage and Charging Messages .
Page 93 (If Equipped). C. Turn and Lane Change Lever. . Driver Information Center Buttons. See . Driver Information Center Display. See F. Info Display. (If Equipped). S. PRNDL. See T. Shift Lever. See . Power Rear Sunshade.
Page 94 The adjustment lever is located on the left side of the steering column. To adjust the steering wheel: 1. Pull the lever down. 2. Move the steering wheel up or down and in or out to a comfortable position. 3. Pull the lever up to lock the steering wheel in place.
Page 95 For vehicles ® ® with an OnStar , Bluetooth or navigation system, press to interact with those systems. See , or the separate navigation manual for more information. Press to silence the vehicle speakers only. Press again to turn the sound on. For vehicles with OnStar or Bluetooth systems, press to reject an incoming call, or end a...
Page 96 Turn the band up for more frequent wipes or down for less frequent wipes. Turns the windshield wipers off. Single wipe, briefly move the wiper lever down. Several wipes, hold the wiper lever down. Clear ice and snow from the wiper blades before using them.
Page 97 The vehicle may have a compass display on the Driver Information Center (DIC). The compass receives its heading and other information from Global Positioning System (GPS) antenna, StabiliTrak, and vehicle speed information. Avoid covering the GPS antenna for long periods of time with objects that may interfere with the antenna's ability to receive a satellite signal.
Page 98 The infotainment system controls are used to access the time and date settings through the menu system. See for information about how to use the menu system. 1. Press the CONFIG button and select Time and Date Settings, or press the button.
Page 99 The accessory power outlets can be used to connect electrical equipment, such as a cellular phone. There are two accessory power outlets, one is located inside the center console storage and other on the rear of the center floor console. Open the protective cover to use the accessory power outlet.
Page 100 The indicator light does not come on when the ignition is in LOCK/OFF or if no equipment is plugged into the outlet. If you try to connect equipment using more than 150 watts or a system fault is detected, the equipment may operate for a short period and turn itself off.
Page 102 The speedometer shows the vehicle's speed in both kilometers per hour (km/h) and miles per hour (mph). The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper-resistant odometer. If the vehicle needs a new odometer installed, the new one is set to the mileage of the old odometer.
Page 103 This gauge shows the engine coolant temperature. If the gauge pointer moves towards the shaded area, the engine is too hot. This reading indicates the same thing as the warning light. It means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as...
Page 104 The front passenger safety belt warning light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop or other electronic device. To turn off the warning light and or chime, remove the object from the seat or buckle the safety belt This light shows if there is an...
Page 105 When the vehicle is started, the passenger airbag status indicator will light the words ON and OFF for several seconds as a system check. If you are using remote start, if equipped, to start the vehicle from a distance you may not see the system check.
Page 106 If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner. A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems.
Page 107 The following can prevent more serious damage to the vehicle: Reduce vehicle speed. Avoid hard accelerations. Avoid steep uphill grades. If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light continues to flash, when it is safe to do so, stop the vehicle.
Page 108 Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: The vehicle will not pass this inspection if the check engine light is on with the engine...
Page 109 The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.
Page 110 If the light comes on while driving, stop as soon as it is safely possible and turn off the vehicle. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service.
Page 111 For vehicles with the uplevel cluster, this light is shown in the Driver Information Center (DIC) screen. for more information. This light comes on when the Electronic Stability Control (ESC) system is turned off. When the ESC is off the Traction Control System (TCS) is also off, wheel spin is not limited.
Page 112 Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. The oil pressure light should come on briefly as the engine is started.
Page 113 This light flashes when the security system is activated. For more information, see For vehicles with the uplevel cluster this telltale displays in the Driver Information Center (DIC) screen. This light comes on when the high-beam headlamps are in use. for more information.
Page 114 This light is white whenever the cruise control is set and turns green when the cruise control is active. The light goes out when the cruise control is turned off. See for more information. For vehicles with the uplevel cluster this telltale will be shown in the Driver Information Center (DIC) screen.
Page 115 Press to get to the Trip/Fuel Menu and the Vehicle Information Menu. Use to scroll through the items in each menu. A small marker will move across the bottom of the page as you scroll through the items. This shows where each page is in the menu.
Page 116 This display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. The fuel economy can be reset by pressing SET while the Average Fuel Economy display is showing.
Page 117 The display will show a vehicle with the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or pounds per square inch (psi). See more information. This display shows an estimate of the oil's remaining useful life. If Remaining Oil Life 99% is displayed, that means 99% of the current oil life remains.
Page 118 The images are projected through the HUD lens located on the driver's side of the instrument panel. The tap shift gear will also appear on the HUD if the vehicle has tap shift and it is active. The HUD information can be displayed in one of three languages, English, French, or Spanish.
Page 119 is reduced when radio, CD information, warnings, or turn-by-turn navigation information are displayed on the HUD. The HUD control is located to the left of the steering wheel. To adjust the HUD image so that items are properly displayed, do the following: 1.
Page 120 This display includes the information in Format One without the transmission information, the outside air temperature, and compass heading. This display includes all the information in Format One along with a circular tachometer, but without outside air temperature and compass heading. All formats will show the turn-by-turn navigation information and provide details about the next driving...
Page 121 The HUD image can temporarily light up depending on the angle and position of the sunlight on the HUD display. This is normal and will change when the angle of the sunlight on the HUD display changes. Polarized sunglasses could make the HUD image harder to see.
Page 122 This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that features are disabled, this message is displayed.
Page 123 If this message displays when attempting to activate cruise control, apply the brake and then try again. This message will display when the cruise control is set and it will show the speed it was set to. See for more information.
Page 124 This message will display if the coolant is low, see This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation.
Page 125 This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven.
Page 126 This message displays when there is a problem with the All-Wheel Drive (AWD) System. See your dealer/retailer for service. This message displays when there is a problem with the Traction Control System (TCS). When this message is displayed, the system will not limit wheel spin.
Page 127 This message displays if there is a problem with the transmission. See your dealer/retailer. This message displays when the transmission needs to be shifted to P (Park). This may appear when attempting to remove the key from the ignition if the vehicle is not in P (Park).
Page 128 1. Press CONFIG to access the Configuration Settings menu. 2. Turn the MENU / SELECT knob to highlight Vehicle Settings. 3. Press the center of the MENU / SELECT knob to select the Vehicle Settings menu. The following list of menu items will be available: Climate and Air Quality Comfort and Convenience...
Page 129 When on, this feature will turn the cooled seats on when using remote start on warm days. Press the MENU / SELECT knob when Remote Start Cooled Seats is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu.
Page 130 This allows you to turn the easy exit seat feature on or off. Press the MENU / SELECT knob when Driver Seat Easy Exit is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu. This allows you to turn the park tilt mirrors feature on or off.
Page 131 Select Power Door Locks and the following will be displayed: Unlocked Door Anti Lock Out Auto Door Unlock Delayed Door Lock When on, this feature will keep the driver door from locking when the door is open. If off is selected, the Delayed Door Lock menu will be available and the door will lock as programmed through this menu.
Page 132 This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. Press the MENU / SELECT knob when Locking Feedback is highlighted. Turn the knob to select Lights and Horn, Lights Only, Horn Only, or Off.
Page 133 ® OnStar uses several innovative technologies and live advisors to provide a wide range of safety, security, navigation, diagnostics, and calling services. In a crash, built in sensors can automatically alert an OnStar advisor who is immediately connected to the vehicle to see if you need help.
Page 134 The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar call center when pressed, is pressed, or if the airbags or ACR system deploy. This information usually includes the vehicle's GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.g.
Page 135 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/211 of Industry Canada. If the vehicle has this feature, you will see these buttons with one square Light Emitting Diode (LED) indicator light next to them in the headliner.
Page 136 Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes.
Page 137 3. Press and hold for five seconds the newly-trained Universal Home Remote button (selected button from Step 2) while observing the indicator light and garage door activation. If the indicator light stays on continuously or the garage door starts to move when the Universal Home Remote button is pressed and released, then the...
Page 138 To program the remaining two Universal Home Remote buttons, begin with Step 1 of Programming the Universal Home Remote System . If you have questions or need help programming the Universal Home Remote System, call 1 800 355 3515 or go to www.homelink.com.
Page 139 All programmed buttons should be erased when the vehicle is sold or the lease ends. To erase all programmed buttons on the Universal Home Remote device: 1. Press and hold down the two outside buttons until the indicator light begins to flash, after 10 seconds.
Page 149: Table Of Contents
Infotainment System Introduction Introduction ....6-2 Theft-Deterrent Feature ..6-2 Overview (Radio with CD) ..6-3 Overview (Radio with CD/DVD and MEM) .
Page 150: Infotainment System
Infotainment System Introduction Read the following pages to become familiar with the audio system's features. WARNING Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
Page 151: Overview (Radio With Cd)
Overview (Radio with CD) Infotainment System A. VOL/ Turns the system on or off and adjusts the volume. B. FAV Radio: Opens the favorites list. C. Buttons 1 to 6 Radio: Saves and selects favorite stations. D. INFO Radio: Shows available information about the current station.
Page 152 Infotainment System F. CD/AUX Selects the CD player or an external audio source. Radio: Seeks the previous station. CD: Select the previous track or rewinds within a track. CD Eject Removes a disc from the CD slot. Radio: Seeks the next station.
Page 153 Overview (Radio with CD/DVD and MEM) Infotainment System A. VOL/ Turns the system on or off and adjusts the volume. B. FAV Radio: Opens the favorites list. MEM: Opens the favorites list. C. Buttons 1 to 6 Radio: Saves and selects favorite stations.
Page 154 Infotainment System E. TUNE/ Manually selects radio stations and pauses time shifted content. CD/DVD: Select tracks, pauses playback, and stops playback. MEM: Select tracks and pauses playback. F. RADIO/BAND Changes the band while listening to the radio. Selects the radio when listening to a different audio source.
Page 155 Opens the phone main menu. Mutes the audio system. S. MEM/DVD/AUX Selects MEM, CD/DVD, USB, or a connected front or rear auxillary audio source. Operation Controls The infotainment system is operated by using the pushbuttons, multifunction knobs, menus that are shown on the display, and steering wheel controls, if equipped.
Page 156 Infotainment System Selecting a Menu Option 1. Turn the Menu knob to move the highlighted bar. 2. Press the SELECT button to select the highlighted option. Submenus An arrow on the right hand edge of the menu indicates that it has a submenu with other options.
Page 157 Press the BACK button to delete the last character in the sequence or press and hold to delete the entire character sequence. Audio Settings The audio settings can be set for each radio band and each audio player source. To quickly reset an audio setting value to 0: 1.
Page 158 6-10 Infotainment System Adjusting the EQ (Equalizer) For vehicles that have an equalizer: 1. Press the TONE button. 2. Select EQ. 3. Select the setting. Press the BACK button to go back to the Tone Settings menu. DSP (Digital Signal Processing) Settings For vehicles with DSP, it is used to provide a choice of different...
Page 159 System Settings Configuring the Number of Favorite Pages To configure the number of available favorite pages: 1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Radio Favorites. 4. Select the number of available favorite pages. 5. Press the BACK button to go back to the System Configuration menu.
Page 160: And Mem)
6-12 Infotainment System Radio AM-FM Radio Control Buttons The buttons used to control the radio are: RADIO / BAND: Press to turn the radio on and choose between AM, FM, and XM , if equipped. Menu Knob: Turn to navigate the available menus.
Page 161 Manual Tuning Turn the TUNE knob to select the frequency on the display. Favorites List 1. Turn the menu knob. 2. Select Favorites List. 3. Select the station. Station Lists 1. Turn the menu knob. 2. Select AM or FM Station List. All receivable stations in the current reception area are displayed.
Page 162: Satellite Radio
6-14 Infotainment System Storing Stations To store the station to a position in the list, press the corresponding button 1 to 6 until a beep is heard. Retrieving Stations Press the FAV button to open a favorite page or to switch to another favorite page.
Page 163 XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. A service fee is required to receive the XM service.
Page 164 6-16 Infotainment System Selecting a Channel Using (Radio with CD/DVD and MEM) Press and release to go to the previous or next channel. Selecting a Channel Using the TUNE Knob To select an XM channel using the TUNE knob: Turn the TUNE knob to highlight an XM channel, the channel is selected after a short delay.
Page 165 Press and release the buttons to go to the next or previous song in the time shift buffer. When the channel is changed, the buffer is cleared and automatically restarted for the current channel. Content from a previously tuned station is no longer available. The time shift feature is not available while recording or with other sources of playback.
Page 166: Radio Reception
6-18 Infotainment System CAT Not Found: The system is working properly. There are no channels available for the selected category. XM Radio ID: If tuned to channel 0, this message alternates with the XM Radio 8 digit radio ID label. This label is needed to activate the service.
Page 167: Backglass Antenna
Cellular Phone Usage Cellular phone usage may cause interference with the vehicle's radio. This interference may occur when making or receiving phone calls, charging the phone's battery, or simply having the phone on. This interference can cause an increased level of static while listening to the radio.
Page 168: Audio Players
6-20 Infotainment System Audio Players CD Player The CD player can play audio CDs and MP3 CDs. The CD player will not play 8 cm (3 in.) CDs. Care of CDs Sound quality can be reduced due to disc quality, recording method, quality of the music recorded, and how the disc has been handled.
Page 169 Removing a CD Press the button. The disc is pushed out of the CD slot. If the disc is not removed after it is ejected, it is pulled back in after a few seconds. Playing a CD or MP3 CD Press the CD/AUX button if there is a disc in the player, it begins playing.
Page 170: Cd/Dvd Player
6-22 Infotainment System CD/DVD Player The CD/DVD player can play CDs, DVD As, MP3/WMA CDs, MP3/ WMA DVDs, and DVD Vs. The CD/DVD player will not play 8 cm (3 in.) discs. Care of CDs and DVDs Sound quality can be reduced due to disc quality, recording method, quality of the music recorded, and how the disc has been handled.
Page 171 Inserting a CD or DVD With the printed side facing up, insert a disc into the slot until it is drawn in. Removing a CD or DVD Press the button. The disc is pushed out of the CD/DVD slot. If the disc is not removed after it is ejected, it is pulled back in after a few seconds.
Page 172 6-24 Infotainment System Searching for MP3s on a CD or DVD It is normal for the search feature to take some time to display the information after reading the disc due to the amount of information stored on the disc. The infotainment system automatically switches to FM while the disc is being read.
Page 173 Pausing a DVD 1. Turn the menu knob. 2. Select Pause, to pause the disc. Select unpause to start playback. Navigating the DVD V Disc Menu Use the following actions to navigate the title menu on a DVD V Disc. Select / Enter Cursor UP Cursor DOWN...
Page 174 6-26 Infotainment System Recording From Audio CDs The infotainment system can record the current song playing or all songs from an audio CD to MEM. A status bar appears on the top of the display when the recording process starts and disappears when the process has ended.
Page 175 Stopping the Recording Press the REC button while recording from an MP3/WMA CD or USB storage device to display the stop recording option. Select Stop Recording Song to MEM. Deleting Tracks From MEM Individual tracks and all tracks can be deleted from MEM. To delete individual tracks, press and release the DEL button while the track is playing.
Page 176: Auxiliary Devices
6-28 Infotainment System To remove MEM favorites categories: 1. Press the CONFIG button. 2. Select Radio Settings. 3. Select MEM Favorites. 4. Remove the check mark from the box to remove that MEM favorites category. Replace the check mark to re-add the removed category.
Page 177 3.5 mm Jack Connect a 3.5 mm (1/8 in) cable to the auxiliary input jack to use a portable audio player. Playback of an audio device that is connected to the 3.5 mm jack can only be controlled using the controls on the device.
Page 178 6-30 Infotainment System Repeat Turn the menu knob and set Repeat to On or Off, then press the BACK button to return the main screen. On: Repeats the current track. Off: Playback starts from the beginning of the current track after the last track finishes.
Page 179: Auxiliary Devices (Radio With Cd/Dvd And Mem)
Searching For a Track It is normal for the search feature to take some time to display the information after reading the device due to the amount of information stored. Files that do not have any meta data stored in the ID3 tag display as Unknown.
Page 180 6-32 Infotainment System 3.5 mm Jack Connect a 3.5 mm (1/8 in.) cable to the auxiliary input jack to use a portable audio player. Playback of an audio device that is connected to the 3.5 mm jack can only be controlled using the controls on the device.
Page 181 Connecting and Controlling a USB Drive Files that are not stored in folders are displayed in the root directory (USB). Connecting a USB Drive Connect the USB drive to the USB port. Disconnecting a USB Drive A USB drive should be ejected from the USB port before disconnecting it.
Page 182: Rear Seat Infotainment
6-34 Infotainment System Rear Seat Infotainment Rear Seat Entertainment (RSE) System The vehicle may have a DVD Rear Seat Entertainment (RSE) system. The RSE system works with the vehicle's infotainment system. The DVD player is part of the front radio. The RSE system includes a radio with a DVD player, two rear seat video display screens, audio/video...
Page 183 Push the On/Off button to turn on the headphones. A light on the headphones comes on. If the light does not come on, check the batteries. Intermittent sound or static can also indicate weak batteries. See Battery Replacement later in this section for more information.
Page 184 6-36 Infotainment System Power for auxiliary devices is not supplied by the radio system. To use the auxiliary inputs of the RSE system: 1. Connect the auxiliary device cables to the A/V jacks. 2. Power on both the auxiliary device and the RSE video screen.
Page 185 Video Screens The video screens are located in the back of the driver and front passenger seats. To use the video screen: 1. Push the release button located on the seatback console. 2. Move the screen to the desired viewing position. Push the video screen down into its locked position when it is not in use, the screen turns off automatically.
Page 186 6-38 Infotainment System If a CD, DVD, or MP3 disc is in the Radio DVD slot, the remote control button can be used to turn on the video screen display and start the disc. The infotainment system can also turn on the video screen display.
Page 187 (Next Track/Chapter): Press to go to the beginning of the next chapter or track. This button might not work when the DVD is playing the copyright information or the previews. (Fast Reverse): Press to quickly reverse the DVD or CD. To stop fast reversing a DVD video, press .
Page 188 6-40 Infotainment System Battery Replacement To change the remote control batteries: 1. Slide back the rear cover on the remote control. 2. Replace the two batteries in the compartment. 3. Replace the battery cover. Remove the batteries from the remote control if unused for an extended period of time.
Page 189 Tips and Troubleshooting Chart (cont'd) Problem The auxiliary source is running but there is no picture or sound. Sometimes the wireless headphone audio cuts out or buzzes. I lost the remote and/or the headphones. The DVD is playing, but there is no picture or sound.
Page 190: Bluetooth (Overview)
6-42 Infotainment System DVD Distortion Video distortion can occur when operating cellular phones, scanners, CB radios, Global Position Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. It might be necessary to turn off the DVD player when operating one of these devices in or near the vehicle.
Page 191: Controls)
When to Speak: A tone sounds to indicate that the system is ready for a voice command. Wait for the tone and then speak. How to Speak: Speak clearly in a calm and natural voice. Audio System When using the Bluetooth system, sound comes through the vehicle's front audio system speakers and overrides the audio system.
Page 192 6-44 Infotainment System Pairing a Phone 1. Press the CONFIG button. 2. Select Phone Settings. 3. Select Bluetooth. 4. Select Pair Device (Phone). A four digit PIN number appears on the display. If the Add new GPS device option is selected, the system will start a search for Bluetooth Handsfree profile devices just like if Add new Phone was...
Page 193 Making a Call Radio with CD 1. Press the button twice. 2. Enter the character sequence. See Entering a Character Sequence in for more information. 3. Select Call to start dialing the number. Radio with CD/DVD and MEM 1. Press the button.
Page 194 6-46 Infotainment System 4. After the call has been placed, turn the menu knob button and choose Merge Calls. 5. To add more callers to the conference call, repeat steps 1 through 4. The amount of callers that can be added are limited by your wireless service carrier.
Page 195 To link to a different paired phone, see Linking to a Different Phone later in this section. Pairing a Phone 1. Press For vehicles without a navigation system, the system responds Ready , followed by a tone. For vehicles with a navigation system, the system responds with a tone.
Page 196 6-48 Infotainment System Deleting a Paired Phone 1. Press For vehicles without a navigation system, the system responds Ready , followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say Hands Free .
Page 197 Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press For vehicles without a navigation system, the system responds Ready , followed by a tone. For vehicles with a navigation system, the system responds with a tone.
Page 198 6-50 Infotainment System Using the Digit Store Command The digit store command allows a phone number to be stored by entering the digits individually. 1. Press For vehicles without a navigation system, the system responds Ready , followed by a tone. For vehicles with a navigation system, the system responds with a...
Page 199 Using the Directory Command The directory command lists all of the name tags stored by the system. To use the directory command: 1. Press For vehicles without a navigation system, the system responds Ready , followed by a tone. For vehicles with a navigation system, the system responds with a tone.
Page 200 6-52 Infotainment System Using the Delete All Name Tags Command The Delete All Name Tags command deletes all stored phone book name tags and route name tags for OnStar, if stored. To delete all name tags: 1. Press For vehicles without a navigation system, the system responds Ready , followed by a tone.
Page 201 3. Say the entire number without pausing. If the system recognizes the number, it responds with OK, Dialing and dials the number. If the system does not recognize the number, it confirms the numbers followed by a tone. If the number is correct, say Yes .
Page 202 6-54 Infotainment System 2. Say Call . The system responds Call using <phone name>. Please say the name tag , followed by a tone. 3. Say the name tag of the person to call. If the system recognizes the name tag it responds OK, calling, <name tag>...
Page 203 Three Way Calling Three way calling must be supported on the Bluetooth phone and enabled by the wireless service carrier. 1. While on a call, press . The system responds with Ready , followed by a tone. 2. Say Three way call . The system responds with Three way call, please say dial or call .
Page 204 6-56 Infotainment System For vehicles without a navigation system, press during a call with the audio on the cell phone, the audio transfers to the vehicle. For vehicles with a navigation system, press during a call with the audio on the cell phone. If the audio does not transfer to the vehicle, use the audio transfer feature on the cell phone.
Page 205 If the system does not recognize the number, it responds Dial Number, please say yes or no? , followed by a tone. If the number is correct, say Yes . The system responds OK, Sending Number and the dial tones are sent and the call continues.
Page 206 6-58 Infotainment System The pairing process can be started by using the voice recognition system or the controls on the infotainment system. Pairing Information: Up to five cell phones can be paired to the Bluetooth system. The pairing process is disabled when the vehicle is moving.
Page 207 On the cell phone, locate the device named General Motors . Follow the instructions given on the cell phone or follow the voice prompts, to enter the four digit PIN number that has been provided. 4. The system voice prompt requests that you say the name you want used for the phone that is being paired.
Page 208 6-60 Infotainment System A list of all previously paired phones will be displayed. If there is a currently connected phone, a check mark will appear on the right side of the Phone name. Deleting a Paired Phone 1. Press the CONFIG hard key repeatedly until the Phone menu is shown or touch the Phone tab on the screen.
Page 209 5. Once a phone has been deleted, the only way to connect back to that phone is to pair the phone again. See Bluetooth Pairing earlier before the process is started. Linking to a Different Phone In order to link to a different phone, the new phone must be in the vehicle and available to be connected to the Bluetooth system...
Page 210 6-62 Infotainment System 4. Select the phone to be linked and then follow the on screen prompts. 5. The Phone menu will be displayed with the name of the phone linked. Making a Call Press located on the faceplate of the infotainment system, to access the phone menu.
Page 211 2. Enter the desired number by touching the appropriate buttons on the screen or using the rotary knob. 3. Press the CALL button to make the call. Accepting or Declining an Incoming Call When an incoming call is received, the infotainment system mutes any audio being played and sounds a ring tone.
Page 212 6-64 Infotainment System Conference Calling Conference and three way calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. To start a conference while in a current call: 1. Press the hard key on the faceplate until the Phone main screen is shown with the current active call.
Page 213 Dual Tone Multi-Frequency (DTMF) Tones The in-vehicle Bluetooth system can send numbers during a call, this is used when calling a menu driven phone system. 1. Press the hard key. 2. Select Enter Number option and enter the number sequence. The DTMF Tones will be generated on the network as you enter each number.
Page 214 6-66 Infotainment System NOTES...
Page 215: Climate Control Systems
Climate Controls Climate Control Systems Air Vents Maintenance Climate Control Systems Automatic Climate Control System Climate Controls...
Page 216: Climate Controls
Climate Controls Automatic Operation (Temperature Control): Manual Operation (Power): (Fan Control): (Air Delivery Mode Control): (Vent): (Bi-Level): (Tri Level): (Floor): (Defog): (Defrost):...
Page 217 Climate Controls (Air Conditioning): Rear Window Defogger (Rear Window Defogger): Do not try to clear frost or other material from the inside of the front windshield and rear window with a razor blade or anything else that is sharp. This may damage the rear window defogger grid and affect your (Recirculation):...
Page 218 Climate Controls Remote Start Climate Control Dual Automatic Climate Control System Operation: Sensors...
Page 219 Climate Controls Automatic Operation (Driver and Passenger (Air Delivery Mode Temperature Control): Control): ZONE: (Vent): Manual Operation (Bi-Level): (Power): (Fan Control): (Tri Level):...
Page 220 Climate Controls (Floor): (Defog): (Defrost): Auto Defog: (Recirculation/Auto Recirculation): (Air Conditioning):...
Page 221 Climate Controls Rear Window Defogger (Rear Window Defogger): Do not try to clear frost Sensors or other material from the inside of the front windshield and rear window with a razor blade or anything else that is sharp. This may damage the rear window defogger grid and affect your radio's ability to pick up stations clearly.
Page 222: Air Vents
Climate Controls Air Vents Operation Tips Maintenance Air Intake Passenger Compartment Air Filter...
Page 223 Climate Controls...
Page 224 7-10 Climate Controls NOTES...
Page 225 Driving and Operating Driving Information Driving for Better Fuel Economy ....8-2 Defensive Driving ... . . 8-3 Drunk Driving .
Page 226: Driving Information
Driving and Operating Towing General Towing Information ....8-52 Driving Characteristics and Towing Tips ....8-53 Trailer Towing (2.4L L4 Engine) .
Page 227: Defensive Driving
Defensive Driving Defensive driving means always expect the unexpected. The first step in driving defensively is to wear your safety belt, see WARNING Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes. Anticipate what they might do and be ready.
Page 228: Control Of A Vehicle
Driving and Operating Medical research shows that alcohol in a person's system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart. This means that when anyone who has been drinking driver or passenger is in a crash, that person's chance of being killed or permanently disabled is higher than if the person had not been drinking.
Page 229: Steering
If the engine ever stops while the vehicle is being driven, brake normally but do not pump the brakes. If the brakes are pumped, the pedal could get harder to push down. If the engine stops, there will still be some power brake assist but it will be used when the brake is applied.
Page 230: Off-Road Recovery
Driving and Operating Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 231: Loss Of Control
tire contacts the pavement edge. Then turn the steering wheel to go straight down the roadway. Loss of Control Let us review what driving experts say about what happens when the three control systems brakes, steering, and acceleration do not have enough friction where the tires meet the road to do what the driver has asked.
Page 232: Driving On Wet Roads
Driving and Operating Driving on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep standing or flowing water. WARNING Wet brakes can cause crashes.
Page 233: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: Keep the vehicle serviced and in good shape. Check all fluid levels and brakes, tires, cooling system, and transmission.
Page 234 8-10 Driving and Operating improves vehicle stability during hard stops on slippery roads, but apply the brakes sooner than when on dry pavement. Allow greater following distance on any slippery road and watch for slippery spots. Icy patches can occur on otherwise clear roads in shaded areas.
Page 235: If The Vehicle Is Stuck
WARNING (Continued) For more information about carbon monoxide, see Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Page 236: Vehicle Load Limits
8-12 Driving and Operating Rocking the Vehicle to Get it Out Turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction system. Shift back and forth between R (Reverse) and a forward gear, spinning the wheels as little as possible.
Page 237 Tire and Loading Information Label Label Example A vehicle specific Tire and Loading Information label is attached to the vehicle's center pillar (B-pillar). With the driver's door open, you will find the label attached below the door lock post. The Tire and Loading Information label shows the number of occupant seating positions (A), and the maximum...
Page 238 8-14 Driving and Operating The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the XXX amount equals 1400 lbs and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400...
Page 239 Example 2 Vehicle Capacity Weight for Example 2 = 453 kg (1,000 lbs). Subtract Occupant Weight @ 68 kg (150 lbs) × 5 = 340 kg (750 lbs). Available Cargo Weight = 113 kg (250 lbs). Example 3 Vehicle Capacity Weight for Example 3 = 453 kg (1,000 lbs).
Page 240 8-16 Driving and Operating Certification Label Label Example A vehicle specific Certification label is attached to the driver side center pillar (B-pillar). The label tells the gross weight capacity of the vehicle, called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo.
Page 241: Starting And Operating
WARNING (Continued) Never stack heavier things, like suitcases, inside the vehicle so that some of them are above the tops of the seats. Do not leave an unsecured child restraint in the vehicle. When you carry something inside the vehicle, secure it whenever you can.
Page 242: Ignition Positions
8-18 Driving and Operating Ignition Positions (Key Access) The ignition switch has four different positions. Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key. Use the correct key, make sure it is all the way in, and turn it only with your hand.
Page 243 Ignition Positions (Keyless Access) The vehicle has an electronic keyless ignition with push button start. Pressing the button cycles it through three positions, ACC/ACCESSORY, ON/RUN/START and OFF. The transmitter must be in the vehicle for the system to operate. If the push-button start is not working, the vehicle may be near a strong radio antenna signal causing interference to the keyless access...
Page 244: Retained Accessory
8-20 Driving and Operating ON/RUN/START: This position is for driving and starting. With the ignition off, and the brake pedal applied, pressing the button once will place the ignition system in ON/RUN/START. Once engine cranking begins, release the button. Engine cranking will continue until the engine starts.
Page 245 Starting Procedure (Key Access) 1. With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the ignition. The idle speed will go down as your engine gets warm. Do not race the engine immediately after starting it.
Page 246 8-22 Driving and Operating Starting Procedure (Keyless Access) 1. If the vehicle has the keyless access system, the transmitter must be in the vehicle. Put your foot on the brake pedal and push the START button. When the engine begins cranking, let go of the button.
Page 247: Engine Heater
2. If the engine does not start after 5 10 seconds, especially in very cold weather (below 18°C or 0°F), it could be flooded with too much gasoline. Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START, or press the START button, for up to a maximum of 15 seconds.
Page 248: Shifting Into Park
8-24 Driving and Operating 3. Plug it into a normal, grounded 110-volt AC outlet. WARNING Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured.
Page 249: Shifting Out Of Park
toward you. If you can, it means that the shift lever was not fully locked into P (Park). Torque Lock Torque lock is when the weight of the vehicle puts too much force on the parking pawl in the transmission. This happens when parking on a hill and shifting the transmission into P (Park) is not done properly and then it is difficult...
Page 250: Parking Over Things
8-26 Driving and Operating Parking Over Things That Burn WARNING Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust WARNING Engine exhaust contains Carbon Monoxide (CO) which cannot be...
Page 251: Running The Vehicle While
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. WARNING Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Page 252: Automatic Transmission
8-28 Driving and Operating Automatic Transmission The automatic transmission has a shift lever located on the console between the seats. P (Park): This position locks the front wheels. It is the best position to use when starting the engine because the vehicle cannot move easily.
Page 253 To rock the vehicle back and forth to get out of snow, ice or sand without damaging the transmission, see N (Neutral): In this position, the engine does not connect with the wheels. To restart the engine when the vehicle is already moving, use N (Neutral) only.
Page 254: Manual Mode
8-30 Driving and Operating Manual Mode Driver Shift Control (DSC) If you drive the vehicle at high RPMs without upshifting while using Driver Shift Control (DSC), you could damage the vehicle. Always upshift when necessary while using DSC. Driver Shift Control (DSC) allows you to shift an automatic transmission similar to a manual transmission.
Page 255: Drive Systems
The transmission will only allow you to shift into gears appropriate for the vehicle speed and engine Revolutions Per Minute (RPM). The transmission will not automatically shift to the next lower gear if the engine RPM is too high, nor to the next higher gear when the maximum engine RPM is reached.
Page 256: Parking Brake
8-32 Driving and Operating If driving safely on a wet road and it becomes necessary to slam on the brakes and continue braking to avoid a sudden obstacle, a computer senses that the wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel.
Page 257 The system has a Park Brake Status light and a Park Brake Warning light. See . There are also three Driver Information Center (DIC) messages. See for more information. In case of insufficient electrical power, the EPB cannot be applied or released. Before leaving the vehicle, check the park brake status lamp to insure the park brake is applied.
Page 258: Brake Assist
8-34 Driving and Operating EPB Release To release the EPB, place the ignition in the ON/RUN position, apply and hold the brake pedal, and push down momentarily on the EPB switch. If you attempt to release the EPB without the brake pedal applied, a chime will sound, and the DIC message PRESS BRAKE PEDAL TO RELEASE PARK...
Page 259: Ride Control Systems
Ride Control Systems Traction Control System (TCS) The vehicle has a traction control system that limits wheel spin. This is especially useful in slippery road conditions. On a front-wheel-drive vehicle, the system operates if it senses that one or both of the front wheels are spinning or beginning to lose traction.
Page 260: Electronic Stability
8-36 Driving and Operating To turn the system off, press located on the console to the right of the shifter. Press and release and the traction control system turns off and the traction control system warning light comes on. Press again to turn the system back on.
Page 261: Limited-Slip Differential
StabiliTrak can be turned off if needed by pressing and holding until the StabiliTrak Off light comes on the instrument panel. For information on turning TCS off and on, see Traction Control System (TCS) in this section. If cruise control is being used when StabiliTrak activates, the cruise control automatically disengages.
Page 262: Cruise Control
8-38 Driving and Operating Cruise Control With cruise control, the vehicle can maintain a speed of about 40 km/h (25 mph) or more without keeping your foot on the accelerator. Cruise control does not work at speeds below 40 km/h (25 mph). On vehicles with the Traction Control System (TCS) or Electronic Stability Control (ESC), the system...
Page 263 SET/ (Set/Coast): Move the thumbwheel down to set a speed or to decrease the speed. To set a speed: 1. Press to turn the cruise control system on. The indicator light in the instrument panel cluster comes on. 2. Get to the speed desired. 3.
Page 264: Object Detection Systems
8-40 Driving and Operating Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle's speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle's speed.
Page 265 WARNING The Ultrasonic Rear Parking Assist (URPA) system does not replace driver vision. It cannot detect: Objects that are below the bumper, underneath the vehicle, or if they are too close or far from the vehicle Children, pedestrians, bicyclists, or pets. If you do not use proper care before and while backing;...
Page 266: Side Blind Zone
8-42 Driving and Operating When the System Does Not Seem to Work Properly SERVICE PARK ASSIST: If this message occurs, take the vehicle to your dealer/retailer to repair the system. PARK ASSIST OFF: If the URPA system does not activate due to a temporary condition, the message displays on the DIC, see for more information.
Page 267 When the system detects a vehicle in the side blind zone, amber SBZA displays will light up in the side mirrors. This indicates that it may be unsafe to change lanes. Before making a lane change, always check the SBZA display, check the outside and rearview mirrors, look over your shoulder for vehicles and hazards, and use the turn signal.
Page 268 8-44 Driving and Operating SBZA is designed to ignore stationary objects; however, the system may occasionally light up due to guard rails, signs, trees, shrubs, and other stationary objects. This is normal system operation, the vehicle does not need service. SBZA does not operate when the left or right corners of the rear bumper are covered with mud, dirt,...
Page 269: Rear Vision
Rear Vision Camera (RVC) This vehicle may have an RVC system. Read this entire section before using it. The RVC system can assist the driver when backing up by displaying a view of the area behind the vehicle. WARNING The Rear Vision Camera (RVC) system does not replace driver vision.
Page 270 8-46 Driving and Operating 4. Select Rear Camera Options. 5. Select Camera. When a check mark appears next to the Camera option, then the RVC system is on. Symbols The navigation system may have a feature that lets the driver view symbols on the navigation screen while using the RVC.
Page 271 Rear Vision Camera Location The camera is located above the license plate. The area displayed by the camera is limited, it does not display objects that are close to either corner or under the bumper and can vary depending on vehicle orientation or road conditions.
Page 272: Fuel
8-48 Driving and Operating Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. To help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline.
Page 273: Gasoline Specifications
If the vehicle has the 3.6L V6 engine (VIN Code V), use premium unleaded gasoline with a posted octane rating of 91 or higher. You can also use regular unleaded gasoline rated at 87 octane or higher, but the vehicle's acceleration could be slightly reduced, and a slight audible knocking noise, commonly referred to as spark...
Page 274: Fuel Additives
8-50 Driving and Operating Fuel Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, nothing should have to be added to the fuel.
Page 275: Filling The Tank
Filling the Tank WARNING Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn off the engine when refueling.
Page 276: Filling A Portable Fuel
8-52 Driving and Operating Filling a Portable Fuel Container WARNING Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs.
Page 277 For information on towing a disabled vehicle, see . For information on towing the vehicle behind another vehicle such as a motorhome, Driving Characteristics and Towing Tips WARNING The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly.
Page 278 8-54 Driving and Operating Do not use the Fuel Saver Mode when towing. Obey speed limit restrictions. Do not drive faster than the maximum posted speed for trailers, or no more than 90 km/h (55 mph), to reduce wear on the vehicle.
Page 279 When turning with a trailer, make wider turns than normal so the trailer will not strike soft shoulders, curbs, road signs, trees or other objects. Use the turn signal well in advance and avoid jerky or sudden maneuvers. Turn Signals When Towing a Trailer The turn signal indicators on the instrument panel flash whenever...
Page 280: Trailer Towing
8-56 Driving and Operating 4. Reapply the brake pedal. Then apply the parking brake and shift into P (Park). 5. Release the brake pedal. Leaving After Parking on a Hill 1. Apply and hold the brake pedal while you: Start the engine. Shift into a gear.
Page 281 See Weight of the Trailer Tongue later in this section for more information. Maximum trailer weight is calculated assuming only the driver is in the tow vehicle and it has all the required trailering equipment. The weight of additional optional equipment, passengers and cargo in the tow vehicle must be subtracted from the maximum trailer weight.
Page 282: Towing Equipment
8-58 Driving and Operating Towing Equipment Hitches Use the correct hitch equipment. See your dealer/retailer or a hitch dealer for assistance. The rear bumper on the vehicle is not intended for hitches. Do not attach rental hitches or other bumper-type hitches to it. Use only a frame-mounted hitch that does not attach to the bumper.
Page 283 General Information ... 9-2 California Proposition 65 Warning ....9-2 California Perchlorate Materials Requirements .
Page 284 Tire Pressure Monitor Operation ....9-60 Tire Inspection ....9-63 Tire Rotation .
Page 285 Certain types of automotive applications, such as airbag initiators, seat belt pretensioners, and lithium batteries contained in remote keyless transmitters, may contain perchlorate materials. Special handling may be necessary. For additional information, see www.dtsc.ca.gov/hazardouswaste/ perchlorate. Adding non dealer/non retailer accessories to the vehicle can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling,...
Page 286 You can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before attempting any vehicle maintenance task.
Page 287 To open the hood, do the following: 1. Pull the interior hood release handle located to the left of the steering column below the instrument panel. 2. Push the secondary hood release lever, located under the center of the hood above the grille, to the right to disengage it.
Page 289 B. Engine Cover. C. Engine Oil Fill Cap. See D. Engine Oil Dipstick. See E. Transmission Fluid Cap and Dipstick. See F. Brake Master Cylinder Reservoir. See G. Power Steering Reservoir and Cap. See H. Engine Coolant Reservoir and Pressure Cap. See I.
Page 291 B. Power Steering Reservoir and Cap. See C. Engine Oil Fill Cap. See D. Engine Oil Dipstick (Out of View). See E. Engine Cover. F. Transmission Fluid Cap and Dipstick. See G. Brake Master Cylinder Reservoir. See H. Engine Coolant Reservoir and Pressure Cap.
Page 293 B. Power Steering Reservoir and Cap. See C. Engine Oil Fill Cap. See D. Engine Oil Dipstick (Out of View). See E. Engine Cover. F. Transmission Fluid Cap and Dipstick. See G. Brake Master Cylinder Reservoir. See H. Engine Coolant Reservoir and Pressure Cap.
Page 294 If the oil is below the cross-hatched area at the tip of the dipstick, add at least one liter/quart of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see for the location of the engine oil fill cap.
Page 295 Oils meeting these requirements should have the starburst symbol on the container. This symbol indicates that the oil has been certified by the American Petroleum Institute (API). If in an area of extreme cold, where the temperature falls below 29°C ( 20°F), use either an SAE 5W-30 synthetic oil or an SAE 0W-30 engine oil.
Page 296 . Change the oil as soon as possible within the next 1 000 km (600 miles). It is possible that, if driving under the best conditions, the oil life system might not indicate that an oil change is necessary for over a year.
Page 297 It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to your dealer/retailer service department and have it repaired as soon as possible.
Page 298 To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt. If the filter remains caked with dirt, a new filter is required. To inspect or replace the engine air cleaner/filter do the following: 1.
Page 299 1. Remove the screws on top of the engine air cleaner/filter housing. 2. Lift the filter cover housing away from the engine. 3. Pull out the filter. 4. Inspect or replace the engine air cleaner/filter. 5. Lower the filter cover housing toward the engine.
Page 300 A. Electric Engine Cooling Fans B. Coolant Recovery Tank and Pressure Cap An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.
Page 301 The cooling system in the vehicle is ® filled with DEX-COOL engine coolant. This coolant is designed to remain in the vehicle for five years or 240 000 km (150,000 miles), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low.
Page 302 The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant recovery tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. If coolant is visible but the coolant level is not at or above the mark pointed to, add a 50/50 mixture of clean, drinkable...
Page 303 The coolant surge tank pressure cap can be removed when the cooling system, including the surge tank pressure cap and upper radiator hose, is no longer hot. 1. Turn the pressure cap slowly counterclockwise. If a hiss is heard, wait for that to stop. A hiss means there is still some pressure left.
Page 304 The vehicle has several indicators to warn of engine overheating. There is a coolant temperature gauge and a warning light on the instrument panel cluster that indicate an overheated engine condition. See for more information. You may decide not to lift the hood when this warning appears, but instead get service help right away.
Page 305 If the overheat warning displays with no sign of steam: 1. Turn the air conditioning off. 2. Turn the heater on to the highest temperature and to the highest fan speed. Open the windows as necessary. 3. In heavy traffic, let the engine idle in N (Neutral) while stopped.
Page 306 for information on the location of the power steering fluid reservoir. It is not necessary to regularly check power steering fluid unless a leak is suspected in the system or an unusual noise is heard. A fluid loss in this system could indicate a problem.
Page 307 When the engine is hot, the level should be at the hot MAX level. When the engine is cold, the fluid level should be between MIN and MAX on the dipstick. To determine what kind of fluid to use, see .
Page 308 This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.
Page 309 The brake master cylinder reservoir is filled with DOT 3 brake fluid as indicated on the reservoir cap. See for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down: The brake fluid level goes down because of normal brake lining wear.
Page 310 Use only new DOT 3 brake fluid from a sealed container. See Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir. With the wrong kind of fluid in the brake hydraulic system, the brakes might not work well.
Page 311 Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See for tips on working around a battery without getting hurt. Infrequent Usage: Remove the black, negative ( ) cable from the battery to keep the battery from running down.
Page 312 When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. It should be parked on a level surface. 2.
Page 313 When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
Page 314 To replace the windshield wiper blade: 1. Pull the windshield wiper assembly away from the windshield. 2. Lift up on plastic latch in the middle of the wiper blade where the wiper arm attaches. 3. With the latch open, pull the wiper blade down towards the windshield far enough to release it from the J-hooked end of the...
Page 315 The vehicle should be placed so it is perpendicular to the wall or other flat surface. The vehicle should not have any snow, ice, or mud on it. The vehicle should be fully assembled and all other work stopped while headlamp aiming is being performed.
Page 316 4. At the wall measure from the ground upward (A) to the recorded distance from Step 3 and mark it. 5. Draw or tape a horizontal line (B) on the wall the width of the vehicle at the height of the mark in Step 4.
Page 317 9. Make sure that the light from the headlamp is positioned at the bottom edge of the horizontal tape line. The lamp on the left (A) shows the correct headlamp aim. The lamp on the right (B) shows the incorrect headlamp aim.
Page 318 The base model vehicle has a halogen high-beam headlamp, a low-beam/Daytime Running Lamp (DRL) headlamp and a turn signal/ parking lamp on the headlamp assembly. To replace one of these bulbs: 1. Open the hood. See A. Low-Beam Headlamp/DRL B. High-Beam Headlamp C.
Page 319 The up level model vehicle has a high intensity discharge (HID) high/ low beam, a dedicated DRL and a turn signal lamp on the headlamp assembly. The park lamp is also the function of the HID headlamp. See for more information.
Page 320 To replace one of these bulbs: 1. Locate the bulb assembly under the front facia. 2. Disconnect the bulb socket from the electrical connector and pull out the bulb assembly. 3. Remove the old bulb from the bulb socket and push the new bulb straight into the bulb socket until it connects.
Page 321 3. Remove the four plastic wing nuts retaining the taillamp assembly in place. 4. Pull out the taillamp assembly and disconnect the wiring harness. A. Back-up Lamp B. Turn Signal Lamp 5. Turn the bulb socket counterclockwise to remove it. 6.
Page 322 A. Bulb Socket B. Lamp Assembly C. Bulb 3. Turn the bulb socket (A) counterclockwise to remove from lamp assembly (C). 4. Pull the bulb (B) straight out of the bulb socket. 5. Push the replacement bulb straight into the bulb socket and turn the bulb socket clockwise to install into lamp assembly.
Page 323 The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and closes, protecting the circuit until the current load returns to normal or the problem is fixed. This greatly reduces the chance of circuit overload and fire caused by electrical problems.
Page 324 To remove the fuse block cover, squeeze the three retaining clips on the cover and lift it straight up. Wiper Starter Rear Power Windows Sunroof Front Power Windows Antilock Brake System Pump Electric Park Brake...
Page 325 Rear Window Defogger Brake Vacuum Pump Cooling Fan K2 Cooling Fan K1 Transmission Control Module Engine Control Module Battery Engine Control Module Ignition Ignition Coils Even Ignition Coils Odd Engine Control Module Post Catalytic Converter Oxygen Sensor Heater Trans Ignition / Fuel System Control Module Airbag Module...
Page 326 Outside Rear View Mirror, Universal Garage Door Opener, Window Switch Windshield Washer Heated Mirror Canister Vent AFL Battery Theft Deterrent Horn Fuel System Control Module Regulated Voltage Control Sensor Engine Control Module Cooling Fan Cooling Fan Run / Crank Rear Window Defogger Starter Wiper Speed...
Page 327 Press in on the sides of the door to release it from the instrument panel. Pull the door toward you to release it from the hinge. Steering Wheel Controls Backlight Body Control Module 7 Body Control Module 5 Radio ® OnStar Universal Hands Free Phone...
Page 328 Driver Seat Diagnostic Link Connector Airbag Trunk Heater Ventilation Air Conditioning Controller ® Radio, OnStar Universal Hands Free Phone Display Automatic Occupant Sensing Instrument Panel Cluster Discrete Logic Ignition Switch Body Control Module 3 Body Control Module 2 Rear Heater Ventilation Air Conditioning/Blower AC/DC Inverter...
Page 329 Not Used Heated Steering Wheel Not Used Not Used Not Used Not Used Side Blind Zone, Ultrasonic Rear Park Assist Not Used PEPS Not Used Rear Sunshade, Ventilated Seats Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used...
Page 330 Not Used Not Used Electronic Suspension Control Rear Seat Infotainment All Wheel Drive Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used PEPS Not Used Not Used Not Used Seat Ventilation, Sunshade Heated Steering...
Page 331 Poorly maintained and improperly used tires are dangerous. Overloading your tires can cause overheating as a result of too much flexing. You could have an air-out and a serious accident. See Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury.
Page 332 See your dealer/retailer for details regarding winter tire availability and proper tire selection. Also, see If you choose to use winter tires: Use tires of the same brand and tread type on all four wheel positions. Use only radial ply tires of the same size, load range, and speed rating as the original equipment tires.
Page 333 The letters and numbers following the DOT (Department of Transportation) code is the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
Page 334 The letters and numbers following the DOT (Department of Transportation) code is the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
Page 335 The three digit number indicates the tire section width in millimeters from sidewall to sidewall. A two digit number that indicates the tire height to width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide.
Page 336 The relationship of a tire's height to its width. A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim.
Page 337 An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall. load rating for a tire at the maximum permissible inflation pressure for that tire.
Page 338 The portion of a tire between the tread and the bead. alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. The friction between the tire and the road surface. The amount of grip provided. The portion of a tire that comes into contact with the road.
Page 339 Tires need the correct amount of air pressure to operate effectively. A vehicle specific Tire and Loading Information label is attached to your vehicle. This label shows your vehicle's original equipment tires and the correct inflation pressures for your tires when they are cold. The recommended cold tire inflation pressure, shown on the label, is the minimum amount of...
Page 340 Use a good quality pocket-type gauge to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under inflated. Check the tire's inflation pressure when the tires are cold.
Page 341 As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them...
Page 342 This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the vehicle's tires and transmits the tire pressure readings to a receiver...
Page 343 The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle.
Page 344 Each TPMS sensor has a unique identification code. Any time you rotate your vehicle's tires or replace one or more of the TPMS sensors, the identification codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire, passenger side front tire, passenger...
Page 345 6. Press the SET/CLR button again to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode and the TIRE LEARNING ACTIVE message displays on the DIC screen. 7. Start with the driver side front tire. 8.
Page 346 Any time you notice unusual wear, rotate the tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When rotating the vehicle's tires, always use the correct rotation pattern shown here. Do not include the compact spare tire in the tire rotation.
Page 347 Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions influence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which appear when the tires have only 1.6 mm (1/16 inch) or less of tread remaining.
Page 348 GM has developed and matched specific tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating.
Page 349 Mixing tires could cause you to lose control while driving. If you mix tires of different sizes, brands, or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes, brands, or types may also cause damage to your vehicle.
Page 350 If you add wheels or tires that are a different size than your original equipment wheels and tires, this could affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover. Additionally, if your vehicle has electronic systems such as anti lock brakes, rollover airbags, traction control, and electronic stability...
Page 351 The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver, or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with...
Page 352 The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature...
Page 353 Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer/retailer if any of these conditions exist.
Page 354 Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash.
Page 355 If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Page 356 The equipment you need is located in the trunk. 1. Open the trunk. 2. Remove the spare tire cover. 3. Turn the retainer nut counterclockwise and remove the spare tire. 4. Place the spare tire next to the tire being changed. 5.
Page 357 4. Position the jack head, as shown Set the jack to the necessary height before positioning it below the jacking point. 5. Attach the jack handle. Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed.
Page 358 6. Turn the jack handle clockwise to raise the vehicle far enough off the ground for the compact spare to fit under the vehicle. 7. Remove all of the wheel nuts. 8. Remove the flat tire. Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
Page 359 Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash. 11. Put the wheel nuts back on with the rounded end of the nuts toward the wheel. Turn each nut clockwise by hand until the wheel is held against the hub.
Page 360 Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. To store the flat or spare tire and tools: 1.
Page 361 Do not use the compact spare on other vehicles. Do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together. If the battery has run down, try to use another vehicle and some jumper cables to start your vehicle.
Page 362 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. 2. Position the two vehicles so that they are not touching. 3. Set the parking brake firmly and put the shift lever in P (Park). 4.
Page 363 Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
Page 364 8. Connect the other end of the black negative ( ) cable to an unpainted heavy metal engine part (D) away from the dead battery, but not near engine parts that move. 9. Start the engine in the vehicle with the good battery and run the engine at idle speed for at least four minutes.
Page 365 To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/retailer or a professional towing service if the disabled vehicle must be towed. See To tow the vehicle behind another vehicle for recreational purposes such as behind a motorhome, see Recreational...
Page 366 When dinghy towing, the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes. This will ensure proper lubrication of transmission components. Use the following procedure to dinghy tow the vehicle from the front with all four wheels on the ground: 1.
Page 367 Vehicles with front-wheel drive can be dolly towed from the front. Vehicles with all-wheel drive can be dolly towed from the front with a maximum speed not to exceed the legal limit or 50 km/h (30 mph). Use the following procedure to dolly tow the vehicle from the front: 1.
Page 368 Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing the Vehicle later in this section. Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish.
Page 369 To preserve the vehicle's finish, keep it clean by washing it often. Do not wash the vehicle in direct sunlight and use a car washing soap. Do not use cleaning agents that are petroleum based or that contain acid or abrasives, as they can damage the paint, metal or plastic on the vehicle.
Page 370 The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.
Page 371 Clean the outside of the windshield with glass cleaner. Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when cleaning the blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking.
Page 372 At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your dealer/retailer or an underbody car washing system can do this.
Page 373 Cleaners can contain solvents that can become concentrated in the vehicle's interior. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning the vehicle's interior, maintain adequate ventilation by opening the vehicle's doors and windows. Do not clean the interior using the following cleaners or techniques: Never use a knife or any other...
Page 374 To clean: 1. Saturate a lint-free, clean white cloth with water or club soda. 2. Remove excess moisture. 3. Start on the outside edge of the soil and gently rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled.
Page 375 To remove dust, a soft cloth dampened with water can be used. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces.
Page 409 Accessories and Modifications ....9-3 Accessory Power ....8-20 Adaptive Forward Lighting (AFL) .
Page 410 Battery ......9-28 Jump Starting ....9-79 Load Management .
Page 411 Climate Control Systems Automatic ..... . 7-1 Dual Automatic ....7-4 Clock .
Page 412 Dual Automatic Climate Control System ....7-4 Rear Seat Entertainment System ..... .6-34 DVD/CD Player .
Page 413 Fuel ......8-48 Additives .....8-50 Economy Driving .
Page 414 Heated and Ventilated Front Seats ......2-8 Heated Front Seats ... . . 2-7 Heated Mirrors .
Page 415 Lights (cont.) Flash-to-Pass ....5-2 Fog Lamps ....4-25 High-Beam On .
Page 416 Object Detection, Side Blind Zone Alert (SBZA) ... 8-42 Odometer ..... . 4-14 Off-Road Recovery .
Page 417 Reading Lamps ....5-5 Rear Seat Entertainment System ..... . . 6-34 Rear Seats .
Page 418 Seats (cont.) Power Adjustment, Front ..2-4 Rear ......2-9 Reclining Seatbacks .
Page 419 Tires (cont.) Inflation Monitor System ..9-60 Inspection ....9-63 Messages ....4-38 Pressure Light .
Page 420 Vehicle Identification Number (VIN) ....11-1 Service Parts Identification Label ......11-1 Ventilation, Air .

Buick 2010 Lacrosse Owner's Manual

6-1 Infotainment System Audio Players

Introduction

Phone

Driving and

Driving Information

Starting and Operating

Automatic Transmission

Drive Systems

Ride Control Systems

Cruise Control

Object Detection Systems

Conversions and Add-Ons

Quick Links

Chapters

Related Manuals for Buick 2010 Lacrosse

Summary of Contents for Buick 2010 Lacrosse

Table of Contents