Table of Contents
Advertisement
32
X-TOUCH COMPACT
X-TOUCH COMPACT RX MIDI DATA
(EN) This RX MIDI data table shows what can get controlled and changed from
outside (via MIDI receive) independent of the X-TOUCH editor software.
(ES) Esta tabla de datos RX MIDI le indica qué puede controlar y modificar desde
el exterior (a través de datos MIDI recibidos) independientemente del
programa editor X-TOUCH.
(FR) Ce tableau de données RX MIDI indique les fonctions pouvant être contrôlées
et modifiées de manière externe (par réception de messages MIDI)
indépendamment de l'éditeur X-TOUCH.
(DE) Diese RX MIDI-Datentabelle zeigt, was man unabhängig von der X-TOUCH
Editorsoftware von außen (via MIDI Receive) steuern und ändern kann.
(PT) Esta tabela de dados RX MIDI mostra o que pode ser controlado e modificado de
fora (através de MIDI receive) independentemente do software editor X-TOUCH.
Function
RX CH
Operation Mode Select
GLOBAL CH
Preset Layer Change
GLOBAL CH
Fader Movement
GLOBAL CH
LED Ring Behavior
GLOBAL CH
Change
LED Ring Remote
GLOBAL CH
Control (Value Change)
Buttons LED Remote
GLOBAL CH
Control
Status LEDs Remote
GLOBAL CH
Control
(IT) Questa tabella dati RX MIDI mostra cosa può essere controllato e modificato
dall'esterno (tramite ricezione MIDI) indipendentemente dal software
dell'editor X-TOUCH.
(NL) Deze RX MIDI-gegevenstabel laat zien wat er van buitenaf (via MIDI-
ontvangst) kan worden bestuurd en gewijzigd, onafhankelijk van de
X-TOUCH-bewerkingssoftware.
(SE) Denna RX MIDI-datatabell visar vad som kan styras och ändras utifrån (via
MIDI-mottagning) oberoende av X-TOUCH-redigeringsprogramvaran.
(PL) Ta tabela danych RX MIDI pokazuje, co można kontrolować i zmieniać z
zewnątrz (przez odbiór MIDI) niezależnie od oprogramowania edytora
X-TOUCH.
RX Command
RX Value
CC 127
0 = Standard Mode, MC Mode LED off
1 = MC Mode, MC Mode LED on
2-127 = ignored
Program Change
ONLY in Standard Mode (see above):
0 = Layer A, A-button LED on
1 = Layer B, B-button LED on
2-127 = ignored
CC 1 – CC 9
0-127 = Fader position, bottom to top
Encoders 1-8:
0 = Single
CC 10 – CC 17
1 = Pan
2 = Fan
Encoders 9-16:
3 = Spread
CC 18 – CC 25
4 = Trim
5-127 = ignored
Encoders 1-8:
0 = all LEDs off
CC 26 – CC 33
1-13 = LEDs 1 (left) – 13 (right) on
14-26 = LEDs 1 (left) – 13 (right) blinking
Encoders 9-16:
27 = all LEDs on
CC 34 – CC 41
28 = all LEDs blinking
29-127 = ignored
Upper Top Row 1-8:
Note off or Note on with Velocity 0: Button LED off
Note 0 – Note 7
Note on with Velocity 1: Button LED on
Note on with Velocity 2: Button LED blinking
Upper Mid Row 9-16:
Note on with Velocity 3-127: ignored
Note 8 – Note 15
Upper Bottom Row 17-24:
Note 16 – Note 23
Lower Row 25-33:
Note 24 – Note 32
Right Area 34-39:
Note 33 – Note 38
Layer A, B LEDs:
Not assignable; only 1 of 2 LEDs lights
if Standard mode selected (see above
"Preset Layer Change")
Foot Switch LED: CC 42
For Foot Switch:
0-63 = LED off
Exp. Pedal LED: CC 43
64-127 = LED on
MC Mode LED:
For Expression Pedal:
Not assignable; lights
LED only on while data transfer (value change)
only if MC mode selected
(see above "Operation Mode Select")
USB LED:
Not assignable; always
active if valid connection
to computer available
MIDI I/O LEDs:
Not assignable; always
active while data transfer
1-8
9-16
17-24
34-39
25-33
Advertisement
Table of Contents
