Table of Contents
Advertisement
• In AV mode, you can change only the “COLOUR SYSTEM”
item.
1. PROGRAMME is the first selected item as you enter the
INSTALL. menu. Press the “ ” or “ ” button to select the
programme number where you want the tuned channel to
be stored. (You may also type the programme number us-
ing the digit buttons)
Note:
• Do not use the PROGRAMME item when you want to
modify the current programme number setting as this may
cause other programmes to be changed that are in the ex-
isting programme number.
2. Press “ ” or “ ” button to select Tuning Mode. By press-
ing “ ” or “ ” button , you can select the mode in which
you want the search to be made, "Channel Search"
mode or "Frequency Search" mode.
• When you select "Channel Search" ("Channel" will be
d i s p l a y e d i n t h e m e n u . ) , t h e d i s p l a y o f t h e
INSTALL.(Installation) Menu will be as below :
3. Press “ ” or “ ” button to select BAND. Using “ ” or “ ”
button to select the band in which you want to search a
channel.
4. Press “ ” or “ ” button to select SEARCH. Press “ ” or
“ ” button to start searching. (Press “ ” button to search
forward. Press “ ” to search backwards.)
• If the found channel is not the desired one, press “ ” or
“ ” button to start searching again.
• To stop searching before a channel is found, press the
reverse direction button. For example, when the TV is
searching forward with “ ” button, press “ ” button to
stop searching.
• If you know the channel number which you want to find,
you can find the channel directly. Follow the step 5 to
select the correct standard, then press “ ” or “ ” to
select CHANNEL again, and press“ ” or “ ” button to
select the channel number, or enter the number with the
digit buttons.
5. If the picture is not clear or no colour appears, change the
colour system to display the picture normally. Press “ ”
or “ ” button to select COLOUR SYSTEM, then press “ ”
or “ ” button to choose the correct one.
• In TV mode: PAL / SECAM
• In AV mode: AUTO / PAL / SECAM / NTSC 3.58 /
NTSC 4.43
6. If the channel reception is poor, fine-tune the channel.
Press “ ” or “ ” to select FINE TUNING, then press “ ”
or “ ” button to fine-tune the channel.
7. After the all settings are completed, store the new
channel’s setting to the programme number which you se-
lected. Press “ ” or “ ” to select STORE, then press
“ ” or “ ” button to store it.
Downloaded from:
http://www.usersmanualguide.com/
QSP BS6HH@
Q#
UVIDIBÃHP9 @
8C6 II@G
76I 9
T
8C6 II@G
%
8PGP VSÃT`TU@H
Q6G
ADI @ÃUVI DIB
T@6S 8C
UVIDIBÃHP9 @
76I 9
8C6 II@G
8PGPVSÃT`TU@H
ADI @ÃUVI DIB
T@6S 8C
TUPS @
8. When you select "Frequency Search" , the display of the
Tuning menu will be as below :
QSP BS6HH@
UVIDIBÃHP9@
8PGPVSÃT`TU@H
AS@R V@I8`
T@6S 8C
TUPS @
• As "Frequency Search" is selected, TV will search ac-
cording to the channel frequencies.
• With the“ ” or “ ” button, select Search. Search can be
made either forward, pressing “ ” button or backwards,
pressing “ ” button.
• The search will be done with steps of 0.25MHz. in each
step.
• If the tuned station is not the desired one, you can continue
searching pressing “ ” or “ ” button again.
• When the desired station is tuned, select STORE using
“ ” or “ ” button and store it to the programme number
you selected pressing “ ” or “ ” button or press “OK” but-
ton.
• Now as you had selected the Frequency Search, the tuning
mode of the program is stored as Frequency Search Mode.
Direct Frequency Access
• If you know the channel frequency of the station you want
to tune, you do not need to make search; select Fre-
quency, using “ ” or “ ” button in the Frequency Mode
Tuning Menu. You can type the first 3 digits of the fre-
quency using the digit buttons, and then you can select the
decimal part of the frequency by using “ ” or “ ” buttons
with 250kHz steps. For example if you want to tune the sta-
tion at frequency 224.25 MHz; first you can directly type
224. The bar at bottom of the menu will show 224.00 . Then
by increasing or decreasing with 0.25 MHz steps using “ ”
or “ ” buttons, you can select the 224.25MHz .When you
type and select the frequency, the corresponding station
will be displayed.
• To store the station to the programme number selected, se-
lect STORE option using “ ” or “ ” button and then press
“ ” or “ ” button or press “OK” button.
• Now as you had selected the Frequency Search, the tuning
mode of the program is stored as Frequency Search Mode.
Note : Channel Search Tuning Mode uses a channel table.
The channels and stations at the table may vary from table to
table and from country to country. Each channel has an ex-
act frequency on the table.
• Frequency Search Tuning Mode does not use a channel
table and it is slower than Channel Search Tuning Mode.
• Channel Search Tuning Mode is recommended for the
countries which uses standard channel table.
• Frequency Search Tuning Mode recommended for the
countries which uses non-standard channel table.
- 14 -
8C6 II@G
T
%
Q6G
Q#
AS@R V@I8`
Q6G
#!$
Advertisement
Table of Contents
