Maintenance; Protecting The Environment - DeWalt DCF680 Original Instructions Manual

English
Proper Hand Position (Fig. E1–E3)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
DCF680
Proper hand position requires one hand on the main handle as
shown in Figure E1.

WARNING: If the tool will be used in elongate position
and highest MR please hold tool with both hands as
shown in Figure E2.
DCF682
Proper hand position requires two hand on the tool as shown
in Figure E3.
Screwdriving (Fig. A, E)
Your screwdriver uses gyroscopic technology to sense your
hand motion. To operate, press in the motion control activation
trigger and turn your hand in the direction that you want the
screwdriver to operate.
Setting Initial Starting Point
1. Grasp the screwdriver as shown in Figure E.
2. Press and hold in the motion control activation trigger.
3. When the LED illuminates the tool is ready for use.
4. To reset initial starting point first release the motion control
activation trigger. Move tool to new position, then press and
hold in the motion control activation trigger.
Operating in Forward Direction
1. Grasp the screwdriver as shown in Figure E.
2. Engage head of fastener with screwdriver accessory on work
piece. Follow instructions for setting initial starting point.
3. Rotate your hand clockwise and the screwdriver will activate
in the forward direction.
Operating in Reverse Direction
1. Grasp the screwdriver as shown in Figure E.
2. Engage head of fastener with screwdriver accessory on work
piece. Follow instructions for setting initial starting point.
3. Rotate your hand anti-clockwise and the screwdriver will
activate in the reverse direction.
To turn the tool off, release the motion control activation trigger.
nOTE: When the tool is not in use or during transit please be
sure to remove any accessory from the tool and activate trigger
lock 2 .
Variable speed
• The spindle speed is dependent upon the speed that you
rotate your hand.
• The slower you rotate your hand, the slower the
screwdriver turns.
• The faster you rotate your hand, the faster the
screwdriver turns.
10
• If you wish to increase the spindle speed, rotate your hand
further in the same direction.
• If you wish to decrease the spindle speed, rotate your hand
back towards the initial starting point.

MAINTENANCE

Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
WALT recommended
e