Page 3
IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety pre- cautions should always be followed to reduce the risk of fire, electric shock and injury to persons. The precautions are listed below. 1. Do not use this product near water (for exam- ple, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swim- ming pool).
Page 4
AFFIDAVIT REQUIREMENTS FOR CONNECTION TO DIGITAL SERVICES • An affidavit is required to be given to the telephone company whenever digital terminal equipment with- out encoded analog content and billing protection is used to transmit digital signals containing encoded analog content which are intended for eventual con- version into voiceband analog signals and transmitted on the network.
Page 5
AFFIDAVIT FOR CONNECTION OF CUSTOMER PREMISES EQUIPMENT TO 1.544 MBPS AND/OR SUBRATE DIGITAL SERVICES For the work to be performed in the certified territory of _______________ (telco name) State of ___________________ County of _________________ I, ______________________________(name), ________________________________(business address), ______________________ (telephone number) being duly sworn, state: I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544 Mbps...
Page 6
( ) The encoded analog content and billing protection is factory set and is not under the control of the customer. I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, maintenance, and adjustment of the encoded analog content and billing in- formation has (have) been trained to perform these func- tions by successfully having completed one of the following (check appropriate blocks):...
Page 7
_________________________________Signature _________________________________Title _________________________________ Date Transcribed and sworn to before me This ________ day of ________, 199___ _________________________________ Notary Public My commission expires: _________________________________ 61200242L1-1 NT1 ACE User Manual...
Page 8
FCC INFORMATION This device complies with Part 15 of the FCC rules. Oper- ation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not ex- pressly approved by the party responsible for compliance could void the user's authority to op-...
Page 9
4. If experiencing difficulty with this equipment, please con- tact ADTRAN for repair and warranty information. The telephone company may require this equipment to be dis- connected from the network until the problem is correct- ed, or it is certain the equipment is not malfunctioning.
Page 10
7. The following information may be required when ap- plying to the local telephone company for leased line facilities. Service Digital Facility Type Interface Code ISDN 02IS5 8. The FCC recommends that the AC outlet, to which equipment requiring AC power is to be installed, is pro- vided with an AC surge arrester.
Page 11
CANADIAN EMISSIONS REQUIREMENTS This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard enti- tled "Digital Apparatus," ICES-003 of the Department of Communications. Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Class B prescrites dans la norme sur le materiel brouil- leur: "Appareils Numeriques,"...
Page 12
connector assembly (telephone extension cord). Compli- ance with the above conditions may not prevent degrada- tion of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Page 13
Procedure. Return Material Authorization (RMA) is re- quired prior to returning equipment to ADTRAN. LIMITED PRODUCT WARRANTY ADTRAN warrants that for five years from the date of ship- ment to Customer, all products manufactured by ADTRAN will be free from defects in materials and workmanship.
Page 14
EXCLUSION OF IMPLIED WARRANTIES, SO THIS EXCLUSION MAY NOT APPLY TO CUSTOMER. In no event will ADTRAN or its suppliers be liable to Cus- tomer for any incidental, special, punitive, exemplary or con- sequential damages experienced by either Customer or a third party (including, but not limited to, loss of data or infor- mation, loss of profits, or loss of use).
ISDN terminal equipment (S/T) and the basic rate ISDN network (U). Figure 1-1 is an illus- tration of the NT1 ACE Figure 1-1. ADTRAN NT1 ACE Figure 1-2 shows the interface connectors. 12VDC POWER Figure 1-2.
ANSI T1.605 and ETSI ETS 300012 Standard. The ADTRAN NT1 ACE is a stand-alone unit and is pow- ered by an external power supply (the ADTRAN power supply, part number 336012VUR01). LED Indicators Table 1-1 describes the status of the LEDs located on the front panel of the NT1 ACE .
This test confirms network integrity to the NT1 ACE Repair and Return Repairs should not be performed in the field. Repair ser- vices can be obtained by returning the unit to the ADTRAN 61200242L1-1 NT1 ACE User Manual...
NT1 ACE User Manual Customer and Product Service (CAPS) Department at the address listed in the back of this manual. Connections The NT1 ACE is optioned for standard 100 ohm termina- tion. Tables 1-2 and 1-3 give the connector pin assignments, and Figures 1-3 and 1-4 show the connectors.
Page 21
Table 1-3. Local Bus Connector Pin Assignments Description No connection No connection S/T interface Receive Power Source 1 (Negative) S/T interface Transmit Power Source 1 (Positive) S/T interface Transmit Power Source 1 (Positive) S/T interface Receive Power Source 1 (Negative) No connection No connection Figure 1-4.
NT1 ACE User Manual Powering with the NT1 ACE The ADTRAN NT1 ACE Power Supply, part number 336012VUR01, provides power to the NT1 ACE the NT1 ACE to the external power supply, perform the fol- lowing steps (see Figure 1-5).
Connecting the Terminal Equipment After successfully powering up the NT1 ACE indicators should be on and the READY indicators should be flashing. Make sure that terminal equipment (TE) is properly terminated. Plug the TE into one of the S/T con- nectors at the rear of the unit.
Figure 1-6. Typical Configuration Troubleshooting If your NT1 ACE does not operate properly, please check the lists of symptoms and solutions below. For further assis- tance, please contact ADTRAN Technical Support at 888- 4ADTRAN. Symptom Action ERROR and READY indi- •...
Page 25
ERROR indicators illumi- Network activation failure: nated; READY indicators • Wall jack wiring is incorrect: Check flash at a faster 8 Hz rate. wall jack. • Problem with ISDN line: Contact telephone company. ERROR indicators illumi- Local bus failure: nated; READY indicators •...
Mechanical Size ...9.0" wide, 6.375" deep, 1.625" high Weight ...1.5 lbs Mounting ...Wall or desktop Power 12 VDC...3.3 W dissipation Environment Temperature...0 to 50 °C (32 to 104 °F) operating ...-20 to 70 °C (-4 to 158 °F) storage Relative Humidity ...Up to 95%, non-condensing Power Supply Specifications Size ...2.5“wide, 3.0"...
Page 28
NT1 ACE User Manual NT1 ACE User Manual 61200242L1-1...
Page 29
Technical Support Repair and Return If ADTRAN Technical Support determines that a repair is needed, Technical Support will coordinate with the Customer and Product Service (CAPS) department to issue an RMA number. For information regarding equipment currently in...