About This Unit; More Information; Troubleshooting - Kenwood DMX120BT Instruction Manual

About this Unit

About this Unit

More information

Ñ Playable Audio files
Audio Bit rate
format
MP3 (.mp3) 16 – 320kbps,
VBR
WMA (.wma) 16 – 320kbps
AAC-LC (.m4a) 16 – 320kbps
WAV (.wav) –
FLAC (.flac) –
• This unit can show ID3 Tag Version 1.0/1.1/2.2/2.3/2.4
(for MP3).
• The maximum number of characters:
– Tag : 30 characters
✎
NOTE
• WMA and AAC of which is covered with DRM cannot
be played.
• Although the audio files are complied with the
standards listed above, the play may be impossible
depending on the types or conditions of media or
device.
Ñ Acceptable Video files
Video Video codec
format
MPEG-1 MPEG-1
(.mpg, .mpeg)
MPEG-2 MPEG-2
(.mpg, .mpeg)
MPEG-4 MPEG-4
(.mp4, .avi)
H.264 H.264
(.mp4, mkv,
avi, .flv, .f4v)
MKV (.mkv) H.264 / MPEG-4 AVC,
MPEG4, WMV (VC1)
WMV (.wmv) WMV (VC1)
Ñ Acceptable Picture files
• JPEG (.jpg)
32 x 32 to 16,241 x 15,225 (JPEG) or 5,847 x 5,481
(Progressive JPEG)
– It may take time to display the file.
– Lossless JPEG files cannot be played.
• BMP (.bmp)
32 x 32 to 9,873 x 9,873 resolution
– It may take time to display the file.
• PNG (.png)
32 x 32 to 8,192 x 7,680
– It may take time to display the file.
Sampling frequency
16 – 48 kHz
16 – 48 kHz
16 – 48 kHz
16 – 192 kHz
16 – 192 kHz
Audio codec
MPEG Audio
Layer 2
MPEG Audio
Layer 2
MP3, AAC-LC (2ch)
MP3, AAC
MP3, AAC, WMA,
Vorbis, FLAC
WMA

Troubleshooting

What appears to be trouble is not always serious.
Check the following points before calling a service
center.
• For operations with the external components, refer
also to the instructions supplied with the adapters
used for the connections (as well as the instructions
supplied with the external components).
Ñ General
No sound comes out of the speakers.
• Adjust the volume to the optimum level.
• Check the cords and connections.
The unit does not work at all.
• Reset the unit. (P.2)
The remote controller does not work.
• Replace the battery.
Ñ USB
While playing a track, sound is sometimes
interrupted.
• The tracks are not properly copied into the USB device.
Copy the tracks again, and try again.
Ñ iPod/iPhone
No sound comes out of the speakers.
• Disconnect the iPod/iPhone, then connect it again.
• Select another source, then reselect "iPod".
The iPod/iPhone does not turn on or does not
work.
• Check the connecting cable and its connection.
• Update the firmware version of iPod/iPhone.
• Charge the battery of iPod/iPhone.
• Reset the iPod/iPhone.
Sound is distorted.
• Deactivate the equalizer either on this unit or the
iPod/iPhone.
A lot of noise is generated.
• Turn off (uncheck) "VoiceOver" on the iPod/iPhone.
For details, visit <http://www.apple.com>.
Ñ Radio
Automatic presetting does not work.
• Store stations manually. (P.12)
Static noise while listening to the radio.
• Connect the antenna firmly.
English | 25