Display Information,Option Buttons; Additional Functions - Siemens WS10X261BY Operating Instructions Manual

Table of Contents

Advertisement

Display information, Option buttons
Display Information
wash: Not on if Rinse
flashing: too much detergent used -> page 13
Rinse: Not on if
Spin: Not on if "
for programme status
On: the door can be opened;
flashing (after programme starts): the door was not closed correctly
On: childproof lock is activated;
flashing: the setting was changed
: Default washing temperature; Cold
90
1000
: Default spin speed of the programme
: Special symbol
1:30: Expected programme duration
Display Information
4.5
: Recommended max. load
Display information
24 h: Select Finish in time
depends on the
chosen programme
: End of programme
: Fault displays
: "YES" if the door can be opened or "NO" if it cannot be
opened during "Pause" period
Option buttons
You can change the default spin speed and temperature even while
the selected programme is running.
Temp.
You can change the indicated washing temperature. The maximum washing temperature which
can be selected depends on the chosen programme.
Spin
You can change the indicated spin speed. The maximum spin speed which can be selected
depends on the chosen programme. You can also set "
Finish in
Before a programme starts, you can specify by how many hours later the programme is to be
ended.
– Press Finish in button until the required number of hours is shown. The Finish in time can be
set in hour increments up to a maximum of 24 hours.
– Press Start/ Reload
, the Finish in time starts counting down.
You can pause the programme to open the door even if the Finish in time is active.
Special symbol
– Except for the
Spin/Empty
hold); the load is held in the final rinsing water. When the programme has ended, "
appear. Select programme
Spin/Empty
speed to spin the laundry.
– When the
Spin/Empty
programme is selected, press the Spin button to set "
programme is then defined as Empty ; If "
– When the Empty
programme has ended,
means the whole process is finished.
or
Spin/Empty
is selected
Spin/Empty
is selected
" Rinse hold is selected
page 6
: cold wash
page 5 Special symbol
page 11
page 7
" -> Special symbol
programme, press the Spin button to set "
or directly press Spin button to select spin
" is not set, the programme is defined as Spin .
and " " appears on the display field, it

Additional functions

Buttons for additional functions
speed Perfect
eco Perfect
Extra rinse
Childproof lock
– Activating the childproof lock: After the programme starts, press Start/Reload
down for 5 seconds until the
The
symbol flashes if any setting is inadvertently changed.
– Deactivating the childproof lock: Press Start/Reload
the
symbol goes out.
– If the programme is ended or any setting is changed, deactivate the childproof lock.
– If the programme is changed while the childproof lock is activated, the
the programme which is running will continue.
– If the childproof lock is deactivated while the programme selector is in a different position
from when the childproof lock was activated, the programme which is currently running be
halted.
Signal
1. Start the signal
mode
2. Set volume for...
*If required, set the volume
repeatedly.
Sleep mode
" (Rinse
If you do not operate the machine for about five minutes after selecting the programme or
"
programme end, the display information goes out to save power.
– If required, press any button, and all information will be displayed again.
", the
5
In addition to the programme if required
For washing in a shorter time with a washing outcome comparable to
that of the standard programme.
For saving energy with a washing performance comparable to that of
the standard programme.
Additional rinse cycles, extended washing time.
For areas with very soft water or for further improvement of the rinsing
result.
Programme will not be changed by accidental operation.
symbol is displayed.
and hold down for 5 seconds until
+
Set to Off
Press Spin and
1 step
hold and
clockwise
Button feedback
Information
signals
signals
directly
set
volume*
1 step
set
clockwise
and hold
symbol flashes,
Release the
button to find
the number
volume*
Set to Off
6

Advertisement

Table of Contents
loading

Table of Contents