Sign in today to find solutions:

Don't have an account? Sign up

Crown Audio Macro-Tech MA-5002VZ Specifications

Crown macro-tech ma-5002vz: specifications.

 
MA-3600VZ
MA-5002VZ
T
he Crown
Macro-Tech
Series is the defi ning
®
®
standard for amplifi er design today. No compro-
mises, no gimmicks. Just brilliant engineering
backed by superior manufacturing, support and an
unsurpassed commitment to quality. Like all Crown
amps, the defi ning characteristic of the Macro-Tech
Series is sonic accuracy. A tight, rock-solid low end,
with smooth, detailed highs and a well-defi ned mid-
range. In short, the most accurate reproduction of an
audio signal you've ever heard. And because we put
the quality of sound above all else, a Crown amplifi er
is the most coveted amplifi er in the business.
When it comes to manufacturing amps, our work is
based on one simple fact: there are no shortcuts to
quality. And our Macro-Techs have proven it time and
time again in some of the most demanding applica-
tions in the world.
®
The VZ
Series is a signifi cant leap forward in ampli-
fi er design. Our patented variable impedance (VZ)
technology permits the MA-3600VZ or MA-5002VZ to
dynamically adapt to signal and load requirements in
real time. Whether you need current in a low-imped-
ance sub-woofer situation, or high-voltage swings for
those transient signals, the VZs deliver!
For more details about the Crown Macro-Tech
Series, contact the Crown Technical Support Group
at 800-342-6939 or 574-294-8200. Also, visit the
Crown Audio website at www.crownaudio.com.
Specifi cations
Note: Specifi cations relate to 120 volt, 60 Hz units
in Stereo mode with 8-ohm loads and an input sen-
sitivity of 26 dB gain at 1 kHz rated power unless
otherwise specifi ed. Specifi cations for units supplied
outside the U.S.A. may vary slightly at different AC
voltages and frequencies.
Power
Output Power: See power charts below.
Load Impedance: Safe with all types of loads, even reac-
tive ones. MA-3600VZ is rated for 2 to16 ohms in Stereo.
MA-5002VZ is rated for 2 to 8 ohms in Stereo. Both
amplifi ers are rated for 4 to 16 ohms in Bridge-Mono and
1 to 4 ohms in Parallel-Mono mode.
Voltage Gain to 8 ohm load at rated output at 1 kHz,
maximum level setting:
MA-3600VZ:
124.6:1 ±6% or 41.9 dB ±0.5 dB at 0.775 volt
sensitivity.
69.2:1 ± 6% or 36.8 dB ±0.5 dB at 1.4 volt sensitiv-
ity.
20:1 ±6% or 26 dB ±0.5 dB at +26 dB sensitivity.
*
1 kHz
MA-3600VZ
Power
1,800W
2 ohm Dual (per ch.)
1,565W
4 ohm Dual (per ch.)
1,120W
8 ohm Dual (per ch.)
3,505W
4 ohm Bridge-Mono
3,140W
8 ohm Bridge-Mono
*1 kHz Power: refers to maximum average power in watts
at 1 kHz with 0.1% THD.
M A C R O - T E C H
Features
• Crown's Grounded Bridge™ design delivers
large voltage swings without using easily
stressed output-transistor confi gurations like
conventional amplifi ers; the results are lower
distortion and superior reliability
®
Patented ODEP
(Output Device Emulation
Protection) circuitry compensates for over-
heating and overload to keep the amplifier
working when others would fail
IOC
®
(Input/Output Comparator) circuitry
immediately alerts of any distortion exceeding
0.05%, providing dynamic proof of distortion-
free performance
MA-5002VZ accepts Crown PIP2 modules. MA-
3600VZ accepts only the PIP-Lite module when
fi tted with the IQ-PIP-USP2 Adapter
Patented Variable Impedance (VZ
supplies for each channel provide excellent
MA-5002VZ:
132:1 ±12% or 42 dB ±1 dB gain at 0.775 volt
sensitivity.
71:1 ±12% or 37 dB ±1 dB gain at 1.4-volt sensitiv-
ity.
20:1 ±3% or 26 dB ±0.25 dB gain at the maximum
level setting.
Required AC Mains (MA-3600VZ): 50/60 Hz;
100, 120, and 230VAC (±10%) units are available.
230VAC, 50/60 Hz units can be used with 220 and
240VAC. All versions draw 90 watts or less at idle.
100VAC and 120VAC units can draw up to 30 amps;
230VAC units can draw up to 15 amps. Current,
voltage and frequency requirements are provided on
unit's back panel.
Required AC Mains (MA-5002VZ): 50 or 60 Hz;
100, 120, 200, 208, 230, 240VAC (±10%). All units
draw 90 watts or less at idle. Current, voltage and
frequency requirements are provided on unit's back
panel.
*
1 kHz
**
MA-5002VZ
Power
2 ohm Dual (per ch.)
2,500W
2,000W
4 ohm Dual (per ch.)
1,300W
8 ohm Dual (per ch.)
5,000W
4 ohm Bridge-Mono
4,000W
8 ohm Bridge-Mono
*1 kHz Power: refers to maximum average power in watts
at 1 kHz with 0.1% THD.
**20 Hz–20 kHz Power: refers to maximum average power
in watts from 20 Hz to 20 kHz with 0.1% THD.
S E R I E S
crosstalk characteristics and the best power
matching to your load; in the MA-5002VZ, three
special modes are provided to control how and
when the supplies shift impedance modes
Very low harmonic and intermodulation distor-
tion result in the best dynamic transfer function
in the industry
MA-5002VZ only: Independent error-driven
compressor for each channel that can be set for
fast or slow attack and release times
Full protection from shorted, open and mis-
matched loads; general overheating; DC;
high-frequency overloads; and internal fault
conditions
Three-Year, No-Fault, Fully Transferable
Warranty completely protects your investment
and guarantees its specifi cations
®
)power
AC Line Connector:
MA-3600VZ: NEMA TT30P.
MA-5002VZ: 10 AWG cordset with NEMA TT30P
plug is provided on 120VAC, 60 Hz North American
units.
Performance
Frequency Response: ±0.1 dB from 20 Hz to 20 kHz
at 1 watt.
Phase Response: ±10 degrees from 10 Hz to 20 kHz
at 1 watt.
Signal-to-Noise Ratio: > 105 dB A-weighted or 100
dB unweighted below rated power, 20 Hz - 20 kHz.
Total Harmonic Distortion (THD):
MA-3600VZ: At full bandwidth power, < 0.05%
from 20 Hz to 1 kHz increasing linearly to < 0.1%
at 20 kHz.
MA-5002VZ: 1 kHz rated power, 0.05% or less true
THD.
Intermodulation Distortion (IMD): (60 Hz and 7
at 4:1)
MA-3600VZ: Less than 0.05% from 368 mil-
20 Hz–20 kHz
liwatts to full bandwidth power.
Power
MA-5002VZ: Less than 0.05% from rated power to
2,155W
35 dB below rated power at 8 ohms.
1,775W
Damping Factor: > 1,000 from 10 Hz to 400 Hz.
Slew Rate: (Slew rates are limited to useful levels for
1,090W
ultrasonic/RF protection.) > 30 volts per microsecond.
Controls
3,670W
Compressor (MA-5002VZ only): A three-position
back-panel switch is used to control each channel's
input compressor. The "fast" setting provides an
attack time of 4 milliseconds and a release time of
300 milliseconds; the "slow" setting provides an
kHz

Summary of Contents

  • Page 1

    In short, the most accurate reproduction of an audio signal you’ve ever heard. And because we put the quality of sound above all else, a Crown amplifi er is the most coveted amplifi er in the business. When it comes to manufacturing amps, our work is based on one simple fact: there are no shortcuts to quality.

  • Page 2

    And the coverage is transferable, should you sell your amplifi er. See your authorized Crown dealer for full warranty disclosure and details. For customers outside of the USA, please contact your authorized Crown distributor for warranty information or call 574-294-8200.

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: