Miele T 8861 WP Edition 111 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Miele Manuals
  4. Dryer
  5. T 8861 WP Edition 111
  6. Operating instructions manual

Miele T 8861 WP Edition 111 Operating Instructions Manual

Heat pump tumble dryer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Operating instructions
for heat pump tumble dryer
T 8861 WP Edition 111
en - AU, NZ
To avoid the risk of accidents or
damage to the appliance, it is
essential to read these instructions
before it is installed and used for the
first time.
M.-Nr. 09 402 480

Advertisement

Table of Contents
loading

Related Manuals for Miele T 8861 WP Edition 111

Summary of Contents for Miele T 8861 WP Edition 111

  • Page 1 Operating instructions for heat pump tumble dryer T 8861 WP Edition 111 en - AU, NZ To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time.

  • Page 2: Caring For The Environment

    Caring for the environment Disposal of the packing Energy saving tips material To avoid unnecessarily long drying times and high consumption of energy: The packing material protects the tumble dryer from transport damage. – Make sure that your laundry is The transport and protective packing thoroughly spun before drying.

  • Page 3: Table Of Contents

    Contents Caring for the environment ......... . 2 Warning and Safety instructions .
  • Page 4 Contents Surfaces of the fluff filters ......... . . 28 Cleaning without water .
  • Page 5 Contents Consumption data ..........49 Technical data .

  • Page 6: Warning And Safety Instructions

    Any other usage is not supported by the manufacturer and could be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation of the tumble dryer.
  • Page 7 Warning and Safety instructions The tumble dryer is not suitable for outdoor use. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they are supervised whilst using it or have been shown how to use it correctly by a person responsible for their safety.
  • Page 8 Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock). The heat pump technology in the tumble dryer uses a refrigerant which is condensed by a compressor.
  • Page 9 Warning and Safety instructions Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician. Faulty components must only be replaced by genuine Miele spare parts.
  • Page 10 Warning and Safety instructions Correct use Caution! Risk of fire. To avoid the possible danger of fire, please read these warnings carefully. A clogged filter is a fire hazard! The fluff filter must be cleaned after every programme. Remove all objects from pockets such as lighters and matches. To prevent the risk of fire, the following textiles must not be dried in this tumble dryer: –...
  • Page 11 Warning and Safety instructions When washing such heavily soiled items, ensure that you use sufficient detergent and select a high temperature. If in doubt, wash the items several times. Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil.
  • Page 12 Warning and Safety instructions In many programmes, the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them (this also avoids the danger of the laundry self-igniting).
  • Page 13 Warning and Safety instructions The tumble dryer must not be used – without the fluff filters in place or if the fluff filters are damaged. – without the fine filter in place or if the fine filters are damaged. This would cause an excessive build-up of fluff which in turn would cause a fault! After every cycle, remove the fluff from the surfaces and the fluff filters (see "Cleaning and care").
  • Page 14 – pets or other small animals climbing into it. The tumble dryer must not be hosed down. Accessories Only use genuine Miele spare parts and accessories with this tumble dryer. If non-Miele parts are used, warranty, performance and product liability claims may be invalidated.

  • Page 15: Operating The Tumble Dryer

    Operating the tumble dryer Control panel a Gentle tumble button g Fault/Check lights For drying items which are not See "Problem solving guide" and suitable for drying with a great deal "After Sales service". of mechanical action. When this h Start/Stop button option is selected, the drum will For starting the programme selected rotate less frequently.
  • Page 16 Operating the tumble dryer The following information appears in The Perfect Dry indicator light remains the display: dark during the following time controlled programmes: Woollens, – Programme duration Warm air, Gentle smoothing. – Programme sequence Drying Estimated time remaining Cooling down The expected time will automatically be Finish displayed (Estimated time remaining).

  • Page 17: Notes On Laundry Care

    Notes on laundry care Care symbols – Loopknit garments (e.g. T-shirts, underwear) have a tendency to Drying shrink after the first wash. Therefore: q/r Normal/lower temperature. To avoid further shrinking, do not overdry these fabrics. When buying This dryer is able to dry at lower loopknit garments, it is advisable to temperatures in each take their shrinkage properties into...

  • Page 18: How To Dry Correctly

    How to dry correctly ^ Switch on the dryer by pressing the Brief instructions jk button. The headings numbered (A, B, C ...) C Load the tumble dryer show the operating sequence and can be used as a brief guide to using your ^ Press the Door button to open the machine.
  • Page 19 How to dry correctly D Selecting a programme Tip: You can extend the range of drying levels for some of the programmes (see "Programmable functions"). Woollens, Gentle smoothing, Proofing programmes – These programmes cannot be changed. Selecting Warm air duration ^ Select the programme you want.
  • Page 20 How to dry correctly F Starting the programme light will flash slowly. Also see "Programmable functions". The Start/Stop button light will flash ^ Press the Door button. when a programme is being selected. The flashing indicates that a ^ Open the door. programme can be started.

  • Page 21: Extra Options/Delay Start

    Extra options/Delay start Extra options To begin Delay start ^ Press the Start/Stop button. The relevant indicator light will come on when selected. – The Delay start indicator light will light up constantly. Gentle tumble – Delay start counts down in one hour For drying items which are not suitable steps to i0^ and afterwards in minute for drying with a great deal of...

  • Page 22: Programme Chart

    Programme chart Extra options Gentle tumble Able to be selected with the following programmes: Cottons, Minimum iron, Shirts, Denim, Warm air. Buzzer Able to be selected with all programmes. Programmes Cottons Max. load: 8 kg* Extra dry, Normal** Fabric type Single and multi-layered cotton fabrics such as towelling, jerseywear, T-shirts, underwear.
  • Page 23 Programme chart Woollens Max. load: 2 kg* Fabric type Fabrics containing wool blends. Notes – Woollen garments are fluffed up. – Remove garments immediately at the end of the programme. Outerwear Max. load: 2.5 kg* Normal, Hand iron Fabric type Outerwear which is suitable for drying in a tumble dryer. Proofing Max.
  • Page 24 Programme chart Hygiene Max. load: 3.5 kg* Fabric type Cottons and linen fabrics, which will be in direct contact with the skin, e.g. underwear, nappies, towelling, bed linen, pillow and mattress covers. Note The temperature is held constant for a longer period of time to deactivate micro-organisms, e.g.

  • Page 25: Changing The Programme Sequence

    Changing the programme sequence Changing Delay start You cannot change to another programme once a programme has ^ See "Delay start". started (this prevents unintentional alterations). Adding or removing laundry You will need to cancel the current after a programme has started programme before you can select a ^ Press the Door button.

  • Page 26: Cleaning And Care

    Cleaning and care Emptying the condensed water container Condensate is collected in the condensed water container during drying. Empty the condensed water container after every drying programme, unless the dryer has been connected for external drainage (see "Installation"). ^ Empty the condensed water If the condensed water container is full, container.

  • Page 27: Adhering To Cleaning Intervals

    Cleaning and care ^ See "Surfaces of the fluff filters". Adhering to cleaning intervals This tumble dryer has a multistage When to clean the fine filter filter system, consisting of the fluff filters in the door and the door Only clean the fine filter if the Clean opening and an additional fine filter.

  • Page 28: Surfaces Of The Fluff Filters

    Cleaning and care Surfaces of the fluff filters Cleaning intervals Clean the surfaces of the fluff filters in the door and the door opening after each drying programme. Cleaning without water Tip: You can use a vacuum cleaner to remove the fluff. ^ Use your fingers or a vacuum cleaner to remove the fluff from the surface of the filter.

  • Page 29: Cleaning With Water

    Cleaning and care Cleaning with water Refitting the filters If there is a great deal of compacted The fluff filters must be dry fluff on any of the filters, they must before they are refitted. Damp or wet be removed and cleaned under hot filters could cause operational faults.

  • Page 30: Fine Filter

    Cleaning and care Fine filter Cleaning intervals Only clean the fine filter if the Clean the filters indicator light comes on. To switch off the Clean the filters indicator light: ^ Remove, clean and refit the fine filter while the dryer is switched on. ^ Pull the fine filter out by the handle.

  • Page 31: Cleaning The Fine Filter Cover Panel

    Otherwise the cooling fins or the ^ Remove any fluff with a damp cloth braces in front of them may be (e.g. Original Miele all purpose damaged. microfibre cloth, available at www.miele-shop.com, depending on In case of visible soiling: country).

  • Page 32: Replacing The Fine Filter

    Cleaning and care Replacing the fine filter Only when the filter is fitted correctly and the cover panel is closed can the condensed water system be sealed and the correct functioning of the tumble dryer be guaranteed. Cleaning the tumble dryer Disconnect the machine from the mains electricity supply.

  • Page 33: Problem Solving Guide

    With the help of the following notes, minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting Miele. A call-out charge will be applied to unnecessary service visits where the problem could have been rectified as described in these Operating instructions.
  • Page 34 If the programme stops again down or Finish is and Cooling down or Finish flashing. flashes again, there is a fault. Contact Miele. The indicator light The dryer is in standby. See "Setting standby" in This is a normal function "Programmable functions".

  • Page 35: An Unsatisfactory Drying Result

    Problem solving guide An unsatisfactory drying result Problem Possible cause Remedy The load consisted of – Final drying cycle with The laundry is not sufficiently dry. different fabrics. Warm air. – Select a different programme next time. Tip: You can alter the drying See "Programmable levels for some functions".

  • Page 36: Other Problems

    Problem solving guide Other problems Problem Possible cause Remedy * The drying Ventilation to and from the Open a door or window while the process goes dryer may be insufficient machine is in operation for on too long or (e.g. because it is installed increased air flow.
  • Page 37 – Has the fuse or circuit breaker tripped? – If you cannot remedy the problem, there is a fault. Call Miele. Power cut. When power is restored to the tumble dryer after a power cut, the programme will continue automatically.

  • Page 38: Cleaning The Cooling Fins (Grille At Bottom Right)

    Problem solving guide Cleaning the cooling fins To avoid damaging the cooling (Grille at bottom right) fins, run the vacuum cleaner (using dusting brush or crevice nozzle) Generally, the cooling fins do not lightly across them without pressure. need to be cleaned. They should only be cleaned if excessive quantities of dust and lint are causing unusually long drying times.

  • Page 39: Changing The Lamp

    ^ Apply a little pressure and, whilst doing so, turn your wrist in the direction of the arrow to open the cover. The cover will open downwards. The temperature resistant lamp should only be ordered from your Miele Chartered Agent or from Miele.

  • Page 40: After Sales Service

    In the event of any faults which you cannot remedy yourself, please contact The indicator or check light marked PC – Miele (see back cover for address). on the control panel is the interface used by the Miele service technicians...

  • Page 41: Installation And Connection

    Installation and connection Front view a Mains connection cable f Four height adjustable screw feet b Control panel g Cool air intake panel (do not block, e.g. with wash basket) c Condensed water container (empty h Hose for external drainage of after every drying programme) condensed water (see "External d Door...

  • Page 42: Rear View

    Installation and connection Rear view If transporting the dryer at an angle, only tip towards the left side. a Protruding lid for holding when moving the machine (see arrows) b Mains connection cable c Hose for external drainage of condensed water d Accessories for connection to a sink drain outlet Transporting the dryer...

  • Page 43: Installation Site

    A building-under kit (Miele a fault. accessory, available to order) with a coverplate to replace the appliance's Building under a continuous...

  • Page 44: Levelling The Machine

    Washer-dryer stack The tumble dryer can also be combined with a Miele washing machine in a washer-dryer stack. The appropriate "WTV" stacking kit* to The machine must be perfectly level to match your dryer is required.

  • Page 45: External Condensed Water Outlet

    Installation and connection External condensed water outlet General notes When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer. The condensed water can also be drained off directly if the machine is installed near a sink, drain outlet etc.

  • Page 46: External Drainage Via A Sink Or Gully

    Installation and connection External drainage via a sink or gully Example: Connection to a sink drain outlet ^ See "Front view" illustration. The drain hose with non-return valve If you want to drain the water off fitted can be connected directly to a into a sink, you will need to secure suitable sink drain outlet.
  • Page 47 Installation and connection ^ Fit adapter 1 to the sink drain outlet using nut 2. If this nut has a flat disc in it, you should take the disc out first. ^ Attach the end of the hose 4 to adapter 1.

  • Page 48: Electrical Connection

    Installation and connection Electrical connection Important This tumble dryer is supplied ready for The wires in the mains lead are connection to an AC single phase coloured in accordance with the supply. The machine is supplied with a following code: mains cable with moulded plug.

  • Page 49: Consumption Data

    Consumption data Load Final spin speed in Residual Energy Duration a domestic washing moisture machine min. Cottons Normal 1000 2.10 Cottons Normal 1200 1.90 1400 1.80 1600 1.60 1800 1.55 Cottons Normal + Gentle tumble 1000 2.15 Cottons Hand ironrr 1000 1.55 Cottons Hand ironrr...

  • Page 50: Technical Data

    Technical data Height 850 mm Width 595 mm Depth 596 mm Depth with door open 1071 mm Height for building under 820 mm Width for building under 600 mm Depth for building under 600 mm Suitable for pushing under a worktop Suitable for stacking Weight...
  • Page 51 Electronic system lock Programmable functions for changing standard settings This tumble dryer is programmed at the factory so that is operates effectively for all requirements. However, you do have the ability to change the standard settings. You can adapt the electronics of the tumble dryer to suit your personal needs.

  • Page 52: Electronic System Lock

    Electronic system lock D Now slowly turn the programme The system lock prevents your selector six positions stage by stage machine being used without your in an anti-clockwise direction. knowledge. Each of the six programme indicator lights must come on one after the You can switch on the system lock if other.

  • Page 53: Programmable Functions

    Programmable functions Extending the range of the The option selected will be displayed drying level for the "Cottons" by a number which will alternate with programme The electronics of this dryer ensure a 0 The drying level will be damper very effective and energy-efficient I Factory default setting drying process.

  • Page 54: Extending The Drying Level For The "Minimum Iron" Programme

    Programmable functions Extending the drying level for The option selected will be displayed the "Minimum iron" by a number which will alternate with programme The electronics of this dryer ensure a 0 The drying level will be damper very effective and energy-efficient I Factory default setting drying process.

  • Page 55: Altering The Anti-Crease Function

    Programmable functions Altering the Anti-crease The option selected will be displayed function by a number which will alternate with Helps prevent creasing if laundry is not normally removed immediately 0 Anti-crease deactivated after the end of a programme. I 1 hour Anti-crease Anti-crease (the Automatic plus indicator light will also flash once)

  • Page 56: Altering The Volume Of The Buzzer

    Programmable functions Altering the volume of the The option selected will be displayed buzzer by a number which will alternate with The buzzer has two volumes. 0 Factory default setting; Normal Follow steps (A,B,C ...) to buzzer programme and store in memory. I Loud buzzer Before you begin, first ensure that: (The Automatic plus indicator light...

  • Page 57: Extending The Drying Level For The "Automatic Plus" Programme

    Programmable functions Extending the drying level for The option selected will be displayed the "Automatic plus" by a number which will alternate with programme The electronics of this dryer ensure a 0 The drying level will be damper very effective and energy-efficient I Factory default setting drying process.

  • Page 58: Setting Standby

    Programmable functions Setting Standby Factory default; Not in current programme To save energy, the display goes out As described under "On". after 10 minutes and the indicator But: The display and indicator lights will light for the Start/Stop button will start not switch off during a programme.
  • Page 59 Programmable functions Before you begin, first ensure that: The option selected will be displayed – The dryer is switched off. by a number which will alternate with – The door is closed. A Press the Start/Stop button and keep 0 On it pressed in whilst carrying out steps I Factory default setting;...

  • Page 60: Memory Function

    Programmable functions Memory function The option selected will be displayed The electronics will memorise any by a number which will alternate with Extra options selected for a programme. The duration selected 0 Factory default setting; Memory for the timed drying programmes will deactivated also be stored in memory.

  • Page 61: Keypad Tone

    Programmable functions Keypad tone The option selected will be displayed An audible tone sounds each time a by a number which will alternate with button is pressed. 0 Factory default setting; Keypad Follow steps (A,B,C ...) to programme and store in memory. tone deactivated I Keypad tone activated Before you begin, first ensure that:...

  • Page 62: Adjusting The Dryer's Electronics For Very Soft Water

    Programmable functions C . . . and then release the Start/Stop Adjusting the dryer's button. electronics for very soft water D Press the Gentle tumble button eight Extremely soft water can affect times. the sensitivity of the control – The Gentle tumble indicator light will electronics.

  • Page 63: Extending The Drying Level Range

    Programmable functions Extending the drying level The option selected will be displayed range by a number which will alternate with You can extend the range of the drying levels for many of the 0 Factory default setting programmes: i Drying level range extended Machine iron + (drier than Machine iron).
  • Page 64 Alteration rights reserved/0313 M.-Nr. 09 402 480 / 00...

Table of Contents