Advertisement
Operation Guide 3079
To recall e-DATA MEMORY records
In the e-DATA MEMORY Mode, use D (+) and B (–) to cycle through e-DATA
MEMORY records as shown below.
Press
Record 1
Record 2
(
)
(
)
Press
Remaining Memory Screen
• The value on the remaining memory screen is the percentage of memory that is still
available. It does not indicate the number of records that can be stored.
• The Password Setting screen shows xxxx when a password is already registered.
• You can use the Password Setting screen to register, edit, or delete your password.
See "Using a Password to Protect e-DATA MEMORY Data" for more information.
To edit an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D (+) and B (–) to display the record you
want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C to move the flashing to the character you want to change.
4. Use D (+) and B (–) to change the character.
5. After making the changes you want, press A to store them and return to the
e-DATA MEMORY record screen.
To delete an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D (+) and B (–) to display the record you
want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and D at the same time to delete the record.
• The message
CLR
appears to indicate that the record is being deleted. After the
record is deleted, the cursor appears on the display, ready for input.
4. Input data or press A to return to the remaining memory screen.
Using a Password to Protect e-DATA MEMORY Data
You can register a 4-digit password to keep e-DATA MEMORY data secure.
Important!
Use a 4-digit password that is easy for you to remember, but difficult for others to
decipher. If you forget the password, you will have to have your watch initialized
(which deletes all data in memory) in order to access the e-DATA MEMORY again. To
have the watch initialized, contact the store or dealer where you purchased it, and ask
to have the AC operation performed.
To register a new password
1. In the e-DATA MEMORY Mode, use D (+) and B (–)
to display the Password Setting screen.
• This displays a screen that shows
2. Hold down A for about one second until
appears, with the first
• This is the New Password Setting screen.
3. Use D (+) and B (–) to scroll through numbers at the first digit.
4. When the first digit is the number you want, press C to advance to the next digit.
5. Repeat steps 3 and 4 to input all four digits of the password you want.
• Pressing A while inputting a new password clears your input and returns to the
Password Setting screen.
6. After all four of the password digits are the way you want, press C to register
them.
• Pressing C causes the message
SET
to appear for about one second as the
password is stored. After that, the Password Setting screen appears.
• After registering a password, you can input, recall, edit and delete data, if you want.
After you exit the e-DATA MEMORY Mode, you will have to input the password
every time you want to enter it again.
To input the password
1. Enter the e-DATA MEMORY Mode.
2. On the Password Input screen (
or B. This causes the first digit of the password to
flash.
3. Input the password.
• Use D (+) and B (–) to scroll through numbers at
each digit.
• Press C to advance to the next digit.
• Pressing A while inputting the password clears your
input and returns to the Password Input screen.
4. After the password is the way you want, press C.
• If the input password matches the one registered, the message
followed by an e-DATA MEMORY screen.
• If the password does not match, the message
Password Input screen.
To change the password
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D (+) and B (–) to display the Password Setting screen.
3. Perform the procedure starting from step 2 under "To register a new password" to
specify the new password.
To delete the password
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D (+) and B (–) to display the Password Setting screen.
3. Hold down A for about one second until
4. Press B and D at the same time to delete the password.
• The message
CLR
appears to indicate that the password is being deleted. After the
password is deleted, the Password Setting screen appears.
.
Remaining
Password
memory
setting
screen
screen
.
Password Setting Screen
SET PA55
.
NEW
0
flashing.
), press D
xxxx PA55
OK!
appears,
ERR
appears, followed by the
NEW
appears, with the first
0
flashing.
World Time
World Time shows the current time in 27 cities (29 time
City code
zones) around the world.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time in another city code
In the World Time Mode, press D to scroll through city
codes (time zones) to the east or B to scroll to the west.
• For full information about city codes, see the "City Code
Table".
• If the current time shown for a city is wrong, check your
Timekeeping
Timekeeping Mode time and Home City code settings
Mode time
and make the necessary changes.
• When the currently selected time zone is one that includes
Current time in the zone
mostly ocean, a value indicating the zone's Greenwich
of the selected city code
Mean Time differential appears in place of a city code.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use B and D to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A for about one second to toggle Daylight
Saving Time (DST displayed) and Standard Time (DST
not displayed).
• The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
• Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
• Note that you cannot switch between Standard Time and Daylight Saving Time while
GMT
is selected as the city code.
Alarms
You can set up to five independent multi-function alarms
Alarm number
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
Alarm time
(Hour : Minutes)
reached. One of the alarms is a snooze alarm, while the
other four are one-time alarms. You can also input
reminder text that appears when the alarm time is
reached.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are five alarm screens numbered
AL4
for the one-time alarm, a snooze alarm screen
indicated by
Timekeeping Mode time
indicated by
• In the case of the snooze alarm screen, the snooze
alarm indicator (
the display.
• Alarm settings (and Hourly Time Signal settings) are available in the Alarm Mode,
which you enter by pressing C.
Alarm Types
The alarm type is determined by the settings you make, as described below.
• • • • • Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
• • • • • Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
• • • • • 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at the time you set, only during the month you set.
• • • • • Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
To set an alarm time
1. In the Alarm Mode, use D and B to scroll through the
alarm screens until the one whose time you want to set
is displayed.
Press
• To set a one-time alarm, display one of the screens indicated by an alarm number
from
AL1
through
AL4
. To set the snooze alarm, display the screen indicated
by
SNZ
.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing in the sequence shown below to select other settings.
Hour
Minutes
Month
• Selecting the text causes the text input cursor (
spaces in the text, so you have to press C eight times to move to the Hour
setting.
AL1
through
SNZ
. The Hourly Time Signal screen is
SIG
.
) appears in the lower right corner of
.
Press
.
Day
Text
) to appear. There are eight
#
2
Hide quick links:
Advertisement
