Intel celeron j3355 processor mini itx motherboard (56 pages)
Summary of Contents for AXIOMTEK MANO522 Series
Page 1
MANO522 Series ® Intel Socket 1151 Core i7/ i5/ i3 Processors Mini ITX Motherboard User’s Manual...
Page 2
Axiomtek does not make any commitment to update the information in this manual. Axiomtek reserves the right to change or revise this document and/or product at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
It discharges static electricity from your body. Wear a wrist-grounding strap, available from most electronic component stores, when handling boards and components. Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co., Ltd. ® ® Intel and Celeron are trademarks of Intel Corporation.
MANO522 Mini ITX Motherboard Section 1 Introduction ® Core™ i7/ The MANO522 Mini-ITX motherboard supports the new 14nm 8 Generation Intel ® ® i5/ i3 and Pentium processors in LGA1151 package. Featuring the new Intel H310 Express chipset with two DDR4 2400/2666MHz memory support, this motherboard is built to perform best stability and reliability for industrial applications.
MANO522 Mini ITX Motherboard Power Input One ATX power input connector. One 12V ATX power input connector for CPU power. Operating Temperature 0°C ~ 60°C. Storage Temperature -20°C ~ 65°C. Form Factor ...
And remove jumper clip from 2 jumper pins to open. The following illustration shows how to set up jumper. Before applying power to MANO522 Series, please make sure all of the jumpers are in factory default position. Below you can find a summary table of all jumpers and onboard default settings.
MANO522 Mini ITX Motherboard 2.3.3 COM1 RS-232/422/485 Mode Select (JP4, JP6, JP7) These are 3x2-pin (pitch=2.0mm) jumpers for setting COM1 port to operate in RS-232, RS-422 or RS-485 communication mode. Function Setting JP4 1-2 close RS-232 mode JP6 3-5, 4-6 close (Default) JP7 3-5, 4-6 close JP4 3-4 close...
MANO522 Mini ITX Motherboard 2.3.7 Case Open Select (JP10) The motherboard has one 2-pin (pitch=2.54mm) jumper for chassis intrusion detection feature. Function Setting Close (Default) 1-2 close Active case open 1-2 open Board and Pin Assignments...
MANO522 Mini ITX Motherboard Connectors Signals go to other parts of the system through connectors. Loose or improper connection might cause problems, please make sure all connectors are properly and firmly connected. Here is a summary table showing connectors on the hardware. Connector Description DIMM1: DDR4 SO-DIMM Connector...
MANO522 Mini ITX Motherboard 2.4.1 SIM Card Slot (CN5) The CN5 is for inserting SIM Card which is mainly used in 3G/4G wireless network application. In order to work properly, the SIM Card must be used together with 3G/4G module which is inserted to CN6. Signal Signal 1 2 3 4...
MANO522 Mini ITX Motherboard 2.4.3 SATA 3.0 Connectors (CN7~CN8) These Serial Advanced Technology Attachment (Serial ATA or SATA) connectors are for SATA 3.0 interfaces allowing up to 6.0Gb/s data transfer rate. They are computer bus interfaces for connecting to devices such as hard disk drives. Signal SATA_TX+ SATA_TX-...
MANO522 Mini ITX Motherboard System Reset Switch Pin 11 and 12 connect the case-mounted reset switch that reboots your computer without turning off the power switch. It is a better way to reboot your system for a longer life of system power supply. HDD Activity LED This connection is linked to hard drive activity LED on the control panel.
MANO522 Mini ITX Motherboard 2.4.6 ATX Power Input Connectors (CN16 and CN17) Steady and sufficient power can be supplied to all components on the board by connecting power connector. Please make sure all components and devices are properly installed before connecting the power connector. External power supply plug fits into the connector in only one orientation.
MANO522 Mini ITX Motherboard 2.4.7 Fan Connectors (CN18 and CN19) The motherboard has two fan connectors. You can find fan speed option within BIOS Setup Utility if fan is installed. For further information, see BIOS Setup Utility: Advanced\Hardware Monitor\PC Health Status in section 4.4. CN18 (CPU fan, 4x1-pin pitch=2.54mm): Signal +12V...
MANO522 Mini ITX Motherboard 2.4.9 COM D-Sub Connector (CN21) The CN21 is a double-deck D-Sub connector for COM1 and COM2 serial port interfaces where only COM1 is selectable for RS-232/422/485 mode by jumper settings (see section 2.3.3). The pin assignments of RS-232/422/485 are listed in table below. COM1: CN21 RS-232...
MANO522 Mini ITX Motherboard 2.4.11 LAN and USB 3.0 Connectors (CN26 and CN27) The motherboard comes with two high performance plug and play Ethernet interfaces (RJ-45) which are fully compliant with the IEEE 802.3 standard. Connection can be established by plugging one end of the Ethernet cable into this RJ-45 connector and the other end to a 1000/100/10 Base-T hub.
MANO522 Mini ITX Motherboard 2.4.13 Front Audio Header (CN29) This is a 5x2-pin (pitch=2.00mm) connector for convenient connection and control of audio devices. Signal Signal MIC_IN LINE_IN_L LINE_IN_R AUD_OUT_L AUD_OUT_R 2.4.14 HDMI Connector (CN30) The HDMI (High-Definition Multimedia Interface) is a compact digital interface which is capable of transmitting high-definition video and high-resolution audio over a single cable.
MANO522 Mini ITX Motherboard 2.4.15 LVDS Signal Header (CN31) This is a 2x20-pin (pitch=1.0mm) connector which is compliant with JST SM40B-SRDS-G-TF for LVDS LCD interface. It is strongly recommended to connect it with matching connector, SHDR-40VS-B. Signal Signal [**] GND(Detect) LVDS_B_DATA3- LVDS_B_DATA0- LVDS_B_DATA3+...
MANO522 Mini ITX Motherboard 2.4.16 LVDS Backlight Control Header (CN32) This is an 8x1-pin (pitch=1.25mm) header which is compliant with Hirose DF13-8P-1.25V for inverter. We strongly recommend you to use the matching connector, DF13-8S-1.25C, to avoid malfunction. Signal +12V +12V LVDS_BKL_EN LVDS_BKL_CTL : This signal is selectable by jumper JP8, see section 2.3.5.
MANO522 Mini ITX Motherboard 2.4.17 M.2 Key E Connector (CN34) The motherboard comes with one M.2 Key E connector (Wi-Fi & Bluetooth). Pin Signal Signal Signal +3.3V BUF_PLT_RST USB#14_D+ NGFF_CLKREQ3 +3.3V BT_KILL1 USB#14_D- PCH_WAKE WLAN_KILL1 CNV_RGI_DT CNV_WR_1_DN CNV_RGI_RSP CNV_WT_1_DN PCM_CRF_RST PCIE12_TX_DP CNV_WR_1_DP CNV_BRI_DT...
MANO522 Mini ITX Motherboard 2.4.18 VGA Connector (CN35) The CN35 is a high rise 15-pin D-Sub connector which is commonly used for VGA display. This VGA interface configuration can be configured via software utility. Signal Signal Green Blue DETECT DDC DATA Horizontal Sync Vertical Sync DDC CLK...
Page 30
MANO522 Mini ITX Motherboard This page is intentionally left blank. Board and Pin Assignments...
Make sure all correct settings are arranged for your installed microprocessor to prevent the CPU from damages. BIOS The MANO522 Series uses AMI Plug and Play BIOS with a single SPI Flash. System Memory The MANO522 supports two 260-pin DDR4 SO-DIMM sockets for maximum memory capacity up to 64GB DDR4 SDRAMs.
Page 32
MANO522 Mini ITX Motherboard This page is intentionally left blank. Hardware Description...
MANO522 Mini ITX Motherboard Section 4 AMI BIOS Setup Utility The AMI UEFI BIOS provides users with a built-in setup program to modify basic system configuration. All configured parameters are stored in a flash chip to save the setup information whenever the power is turned off.
Page 34
MANO522 Mini ITX Motherboard Hot Keys Description Left/Right The Left and Right <Arrow> keys allow you to select a setup screen. The Up and Down <Arrow> keys allow you to select a setup screen or sub Up/Down screen. The <Enter>...
MANO522 Mini ITX Motherboard Main Menu When you first enter the setup utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. System Time/Date can be set up as described below.
MANO522 Mini ITX Motherboard Advanced Menu The Advanced menu also allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus: ►...
Page 37
MANO522 Mini ITX Motherboard IT8786 Super IO Configuration You can use this screen to select options for the Super IO Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen.
Page 38
MANO522 Mini ITX Motherboard Serial Port 1~6 Configuration Serial Port Enable or disable serial port 1~6. The optimal settings for base I/O address and for interrupt request address are: Serial port 1: 3F8h, IRQ4 Serial port 2: 2F8h, IRQ3 Serial port 3: 3E8h, IRQ7 Serial port 4: 2E8h, IRQ6 Serial port 5: 2F0h, IRQ6...
Page 39
MANO522 Mini ITX Motherboard Hardware Monitor This screen monitors hardware health status. This screen displays the temperature of system and CPU, cooling fans speed in RPM and system voltages (VCC_CPU, VCC_DDR, +12V, +5V, +3.3V standby and VBAT). AMI BIOS Setup Utility...
Page 40
MANO522 Mini ITX Motherboard Smart Fan Function This screen allows you to select CPU fan and system fan mode. CPU FAN\System FAN This item allows you to select the fan speed option(s) of CPU fan and system fan (see section 2.4.7) which can be set to Full on, Manual and Automatic Mode.
Page 41
MANO522 Mini ITX Motherboard Automatic Mode: The following selections appear only in Automatic Mode. The initial spinning speed of fan is determined according to start PWM value. The PWM Slope is used to control how fast the fan speeds up or slows down; larger value means faster. When temperature gets higher, the fan increases its speed according to PWM Slope.
Page 42
MANO522 Mini ITX Motherboard Trusted Computing This screen provides function for specifying the TPM settings. Security Device Support Enable or disable BIOS support for security device, see image below. OS will not show security device. TCG EFI protocol and INT1A interface will not be available. Pending operation Schedule an operation for the security device, see image below.
Page 43
MANO522 Mini ITX Motherboard S5 RTC Wake Settings This screen allows user to enable system to wake from S5 using RTC alarm. Wake system from S5 Enable or disable system wake on alarm event. It allows you to wake up the system in a certain time.
Page 44
MANO522 Mini ITX Motherboard ACPI Settings ACPI Sleep State When the suspend button is pressed, the ACPI (Advanced Configuration and Power Interface) sleep state is S3 (Suspend to RAM). AMI BIOS Setup Utility...
Page 45
MANO522 Mini ITX Motherboard CPU Configuration This screen shows CPU information, and you can change the value of the selected option. Intel (VMX) Virtualization Technology Enable or disable Intel Virtualization Technology. When enabled, a VMM (Virtual Machine Mode) can utilize the additional hardware capabilities. It allows a platform to run multiple operating systems and applications independently, hence enabling a single computer system to work as several virtual systems.
Page 46
MANO522 Mini ITX Motherboard Intel(R) SpeedStep(tm) The processor will control the frequency dynamically. Turbo Mode Enable or disable processor Turbo Mode. The processor can run up to maximum turbo frequency when the system loading becomes higher. AMI BIOS Setup Utility...
Page 47
MANO522 Mini ITX Motherboard SATA and RST Configuration During system boot up, BIOS automatically detects the presence of SATA devices. In the SATA Configuration menu, you can see the hardware currently installed in SATA ports. SATA Controller(s) Enable or disable the SATA Controller feature. The default is Enabled. SATA Mode Selection The SATA operation mode is AHCI (Advanced Host Controller Interface).
Page 48
MANO522 Mini ITX Motherboard PCH-FW Configuration This screen displays ME Firmware information. USB Configuration USB Devices Display all detected USB devices. AMI BIOS Setup Utility...
MANO522 Mini ITX Motherboard Chipset Menu The Chipset menu allows users to change the advanced chipset settings. You can select any of the items in the left frame of the screen to go to the sub menus: ► System Agent (SA) Configuration ►...
Page 50
MANO522 Mini ITX Motherboard System Agent (SA) Configuration This screen allows users to configure System Agent (SA) parameters. For items marked with “”, please press <Enter> for more options. Graphics Configuration Open sub menu for parameters related to graphics configuration. Memory Configuration Open sub menu for information related to system memory.
Page 51
MANO522 Mini ITX Motherboard Graphics Configuration Primary IGFX Boot Display Select the video device which will be activated during POST (Power-On Self Test). The default is Auto. The secondary boot display selection will appear based on your selection. Secondary IGFX Boot Display After selecting other than “AUTO”...
Page 52
MANO522 Mini ITX Motherboard LVDS Control Enable or disable LVDS Control. When installing Linux OS and if HDMI or VGA display is connected to your system, make sure to set this option to Disabled. LVDS Panel Type Select the appropriate LVDS panel resolution; see the selection options in image above. Brightness Setting This option appears only when LVDS panel is connected.
Page 53
MANO522 Mini ITX Motherboard Memory Configuration This screen shows the system memory information. AMI BIOS Setup Utility...
Page 54
MANO522 Mini ITX Motherboard PCH-IO Configuration This screen allows you to set PCH parameters. PCH LAN Controller Enable or disable onboard PCH LAN controller. Wake on LAN After enabling PCH LAN Controller, enabling or disabling integrated LAN to wake the system.
MANO522 Mini ITX Motherboard Security Menu The Security menu allows users to change the security settings for the system. Setup Administrator Password Set setup administrator password. User Password Set user password. AMI BIOS Setup Utility...
MANO522 Mini ITX Motherboard Boot Menu The Boot menu allows users to change boot options of the system. Setup Prompt Timeout Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting. Bootup NumLock State Use this item to select the power-on state for the keyboard NumLock. ...
Page 57
MANO522 Mini ITX Motherboard Launch UEFI PXE OpROM policy Control the execution of UEFI PXE OpROM. When enabled, you may select LAN1 or LAN2 as PXE LAN port. Boot Option Priorities These are settings for boot priority. Specify the boot device priority sequence from the available devices.
MANO522 Mini ITX Motherboard Save & Exit Menu The Save & Exit menu allows users to load your system configuration with optimal or fail-safe default values. Save Changes and Exit When you have completed the system configuration changes, select this option to leave Setup and return to Main Menu.
Page 59
MANO522 Mini ITX Motherboard Discard Changes Select this option to quit Setup without making any permanent changes to the system configuration. Select Discard Changes from the Save & Exit menu and press <Enter>. Select Yes to discard changes. Restore Defaults It automatically sets all Setup options to a complete set of default settings when you select this option.
Page 60
MANO522 Mini ITX Motherboard This page is intentionally left blank. AMI BIOS Setup Utility...
MANO522 Mini ITX Motherboard Appendix A Watchdog Timer About Watchdog Timer Software stability is major issue in most application. Some embedded systems are not watched by human for 24 hours. It is usually too slow to wait for someone to reboot when computer hangs.
Page 62
MANO522 Mini ITX Motherboard This page is intentionally left blank. Watchdog Timer...
MANO522 Mini ITX Motherboard Appendix B TPM Settings 1. Setup BitLocker Drive Encryption main storage. Press <Win + R> and type “Control Panel”, then select BitLocker Drive Encryption. TPM Settings...
Page 64
MANO522 Mini ITX Motherboard 2. Insert an external storage device, for example USB Storage. Back up BitLocker recovery key in a new file and save it to the USB Storage. TPM Settings...
Page 65
MANO522 Mini ITX Motherboard 3. Please follow the steps below to encrypt your storage device: TPM Settings...
Page 66
MANO522 Mini ITX Motherboard Now, the system prompts that the operating system drive encryption is in progress, and the encryption progress is checked. TPM Settings...
Page 67
MANO522 Mini ITX Motherboard Select and click the icon in the lower right corner to complete the encryption. TPM Settings...
Page 68
MANO522 Mini ITX Motherboard 4. Confirm the completion of encryption. TPM Settings...
Page 69
MANO522 Mini ITX Motherboard 5. Disable TPM function in BIOS Setup Utility. 6. When the system is powered on and you see the following screen, it means the TPM module function is working fine. Note that BitLocker cannot be executed if your system does not have TPM function.
Page 70
MANO522 Mini ITX Motherboard System with no TPM function support is as below: TPM information is not found in Device Manager. Note When trying to turn on Bitlocker, the following error message shows up. TPM Settings...
Page 71
MANO522 Mini ITX Motherboard TPM Settings...