Brother DCP-165C Quick Setup Manual

Unpack the machine and check the components
1
Start Here
Important
DO NOT
connect the
USB cable yet.
a.
Warnings tell you what to do to
WARNING
prevent possible personal injury.
e.
Gently put the paper into the paper tray. Check that the
paper is flat in the tray.
Note
When you use Legal size paper, press and hold the
universal guide release button
front of the paper tray.
Important
Do not push the paper
in too far.
d.
Fan the stack of paper well.
d.
Unpack the ink cartridge.
Turn the green knob on the protective yellow cap clockwise until it clicks to release the
vacuum seal, then remove the cap a.
1
Set the language (If needed)
6
a.
Press Menu.
b.
Press a or b to choose 0.Initial Setup, and then
press OK.
c.
Press a or b to choose 0.Local Language, and then
press OK.
d.
Press a or b to choose your language.
e.
Press OK and then Stop/Exit.
Before you can use the machine, read this Quick Setup Guide
for the correct setup and installation.
LS6374001
USA/CAN
Printed in China
Note c.
Make sure you have all components.
• The components of your box may differ depending on your
country.
• Save all packing materials and the box in case for any
reason you must ship your machine.
• A USB cable is not included.
You need to purchase a USB 2.0 cable that is no more
than 6 feet (2 meters) long.
Your machine has a USB 2.0 Full-speed interface. This interface
is compatible with USB 2.0 Hi-Speed; however, the maximum
data transfer rate will be 12 Mbits/s. The machine can also be
connected to a computer that has a USB 1.1 interface.
WARNING
b.
a
Remove the protective Remove the plastic bag
Plastic bags are used in the packaging of your
tape and film. containing the ink cartridges
machine. To avoid danger of suffocation, please
from on top of the paper tray.
keep these bags away from babies and children.
f.
Gently adjust the paper side guides to the paper with both hands.
Make sure the paper side guides touch the edges of the paper.
g.
Close the paper tray cover
and slowly push the paper
a
as you slide out the
tray back into the machine.
1
e.
Install each ink cartridge in the direction of the arrow on
the label. Take care to match the color of the lever
with the cartridge color b.
Set the LCD contrast (If needed)
7
a.
Press Menu.
b.
Press a or b to choose 0.Initial Setup, and then
press OK.
c.
Press a or b to choose 2.LCD Contrast, and then
press OK.
d.
Press a or b to choose Dark or Light.
e.
Press OK and then Stop/Exit.
Load plain Letter/A4 paper
2
a.
Pull out the paper tray.
Starter Ink
Cartridges [x4]
1
Black
Yellow
Cyan
Magenta
Accessory
CD-ROM
Order Form
Quick Setup
User's Guide
Guide
Connect the power cord
3
a.
Connect the power cord.
h.
Pull out the paper support a
until it clicks, and then unfold
the paper support flap b.
2
1
f.
Gently push the ink cartridge until it clicks. After all the
a ink cartridges are installed close the ink cartridge cover.
1
2
Note
The machine will prepare the ink tube system for printing.
This process will take approximately four minutes.
Do not turn off the machine.
Set the date and time
8
a.
Press Menu.
b.
Press a or b to choose
0.Initial Setup, and then press OK.
c.
Press a or b to choose
1.Date&Time, and then press OK.
Quick Setup Guide
b. c.
Lift the paper tray cover a.
Press and slide the
paper side guides
a and paper length
b
guide to fit the
1
paper size.
Make sure that the
triangular marks
on the paper side
a
guides and paper
length guide
up with the mark for
the paper size you
are using.
Install the ink cartridges
4
a.
The LCD shows:
No Cartridge
Important
DO NOT connect the b.
Open the ink cartridge cover a.
USB cable yet.
Note
The control panel
warning LED will stay on
until you have installed
the ink cartridges.
Check the print quality
5
a. b.
When the preparation process Check the quality of the four color
has finished, the LCD shows blocks a
this message. (black/yellow/cyan/magenta)
Set Paper and
Press Start
o If all lines are clear and visible, press
Press Color Start.
(Yes) to finish the quality check.
o If you can see missing short lines, press
(No) and follow the steps on the LCD.
d.
Press a or b repeatedly to enter the last two digits of the year, and
then press OK.
Year:2008
(e.g. Enter 08 for 2008.)
e.
Repeat for Month and Day, and Hours and Minutes in 24-hour format.
f.
Press Stop/Exit.
Note
If you make a mistake and want to start again,
press Stop/Exit to go back to step a.
DCP-165C
1
3
c
2
b line
3
c.
Remove the green protective
part a.
1
1
on the sheet.
1
OK
a
Poor
b
Turn the sheet over.