Drill Master 360X User Manual page 4

to determine that it will operate properly and perform its in-
tended function. Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any other condi-
tions that may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced by an autho-
rized service center unless otherwise indicated in the instruc-
tion manual. Have defective switches replaced by an authorized
service center. Do not use the tool if the switch does not turn
it on and off. Do not use if the grinding wheel is damaged. Use
only grinding wheels recommended by Drill Doctor
• NEVER LEAVE TOOL RUNNING UNATTENDED; TURN POW-
ER OFF. Don't leave the tool until it comes to a complete stop.
• USE THE RIGHT TOOL, do not force small tools to do the job of
a heavy duty tool, do not use tools for purposes not intended (
for example do not use this unit to sharpen anything other than
standard twist bits)
• STORE IDLE TOOLS. When not in use, tools should be stored
in a dry, locked-up place out of the reach of children.
• DO NOT ABUSE THE CORD. Never yank the cord to disconnect
it from the socket. Keep the cord away from heat, oil and sharp
edges.
• STAY ALERT. Watch what you are doing, use common sense
and do not operate the tool when you are tired.
• HAVE YOUR TOOL REPAIRED BY A QUALIFIED PERSON.
This electric tool complies with the relevant safety rules. Re-
pairs should only be carried out by qualified persons using
original spare parts; otherwise this may result in considerable
danger to the user.
Grounding Instructions
In the event of a malfunction or breakdown, grounding provides
a path of least resistance for electric current to reduce the risk of
electric shock. Drill Doctor
®
having an equipment-grounding conductor and a grounding plug.
The plug must be plugged into a matching outlet that is properly
wired and grounded (110V or 230V) in accordance with all local
codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it does not fit the
outlet, have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. The conductor with instal-
lation (having an outer surface that is green with or without yel-
4
® .
is equipped with an electric cord
www.drilldoctor.com
low stripes) is the equipment-grounding conductor. If repair or re-
placement of the electric cord or plug is necessary, do not connect
the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if in
doubt as to whether the tool is properly grounded. Use only 3-wire
extension cords that have 3-prong grounding plugs and 3-pole re-
ceptacles that accept the tool's plug. Repair or replace damaged
or worn cord immediately.
GROUNDED, CORD-CONNECTED TOOLS, such as the Drill
Doctor ®
, are intended for use on a supply circuit having a nomi-
nal rating less than 150 volts.
USA Only
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in Figure A
following. It has a grounding plug that looks like the
one in Figure B following. A temporary adapter, which
looks like the adapter illustrated in Figures C & D fol-
lowing, may be used to connect this plug to a 2-pole
receptacle as shown in Figure D if a properly grounded
outlet is not available. The temporary adapter should
be used only until a properly grounded outlet can be
installed by a qualified electrician. The green-colored
rigid ear, lug, and the like, extending from the adapter
must be connected to a permanent ground such as a
properly grounded outlet box.
Cover of
Grounded
Outlet Box
Fig. A
Cover of
Grounded
Outlet Box
Adapter
Metal Screw
Grounding Means
Fig. C
www.drilldoctor.com
Grounding Pin
Fig. B
Fig. D
5