Table of Contents
Advertisement
AVIATOR SP-8™
WARNINGS:
•
Do not spill water or other liquids in to or on to your unit.
•
Be sure that the local power outlet match that or the required volt-
age for your unit.
•
Do not attempt to operate this unit if the power cord has been
frayed or broken. Please route your power cord out of the way of
foot traffic.
•
Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short.
•
Disconnect from main power before making any type of con-
nection.
• Do not remove the top cover under any conditions. There are no
user serviceable parts inside.
• Disconnect the unit's main power when left unused for long
periods of time.
•
Never connect this unit to a dimmer pack
•
Always be sure to mount this unit in area that will allow proper
ventilation. Allow about 6" (15cm) between this device and a wall.
•
Do not attempt to operate this unit, if it becomes damaged in any
any way.
•
Never operate this unit when it's cover is removed.
FEATURES:
Congratulations and thank you for purchasing the American DJ®
AVIATOR SP-8. The AVIATOR SP-8 is a DMX dimmer/switcher pack.
This unit can be programmed to operate as a 1, 2, 4, or 8 channel
dimmer or switcher pack. This unit is perfect for contractor, install-
ers, and professional light companies. The Aviator SP-8™ features
include:
• 3-pin XLR IN and OUT jacks
• Linkable
• Back up memory protection
• 4 digit LCD display
American DJ Supply
- www.americandj.com - AVIATOR SP-8™ Instruction Manual Page 3
©
®
Introduction
AVIATOR SP-8™
Unpacking:
Every AVIATOR SP-8™ has been thoroughly tested and has been
shipped in perfect operating order. Carefully check the shipping carton
for damage that may have occurred during shipping. If the carton
appears to be damaged, carefully inspect your fixture for any damage.
In the case damage has been found please contact our toll free cus-
tomer support number for further instructions.
Power Supply:
Before plugging your unit in be sure the source voltage in your area
matches the required voltage for your American DJ
The American DJ
sion. Because line voltage may vary from venue to venue, you should
be sure to plug your power supply into a matching wall outlet before
attempting to operate you controller.
Data Cable (DMX Cable) Requirements:
Your fixture and your controller require a standard 3-pin XLR connector
for data input and data output (Figure 1). If you are making your own
cables be sure to use standard two conductor shielded cable (This
cable may be purchased at almost all pro sound and lighting stores).
SOUND
Your cables should be made with a male and female XLR connector on
either end of the cable. Also remember that DMX cable must be daisy
chained and can not be "Y"ed or split.
Notice:
nect the cable's shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR's outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
Notice:
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable's
American DJ Supply
©
AVIATOR SP-8
™
is available in a 115v and 230v ver-
®
REMOTE
INPUT
OUTPUT
CONTROL
INPUT
Do not use the ground lug on the XLR connector. Do not con-
POWER
DMX512
DMX+,DMX-,COMMON
Be sure to follow figures two and three when making your own
COMMON
DMX +
1
DMX512 OUT
3
3-PIN XLR
DMX -
2
- www.americandj.com - AVIATOR SP-8™ Instruction Manual Page 4
®
Set Up
AVIATOR SP-8.™
®
REMOTE
INPUT
OUTPUT
SOUND
CONTROL
INPUT
POWER
1
DMX512 IN
3
3
3-PIN XLR
2
SOUND
Termination re
avoids signal
1
and interferen
2
to connect a D
120 Ohm 1/4 W
and PIN 3 (D
Advertisement
Table of Contents
