Archive Menu; System Settings Menu - Bosch DVR1A1081 Installation Instructions Manual

EazeoRecorderInstalA.book Page 17 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 4

4.7 Archive menu

ARCHIVE MENU
PICTURE SIZE
TIME STAMP
TIME STAMP POSITION
WATER MARK
WATER MARK POSITITON
MAIN MENU
PICTURE SIZE: Select picture size for copying image to CF card
Big size: 720x576 (PAL), 720x480 (NTSC)
Small size: 352x288 (PAL), 352x240 (NTSC)
TIME STAMP:
ON: Time stamp appears on the picture when copying image
to CF card.
OFF: Time stamp does not appear on the picture when
copying image to CF card.
TIME STAMP POSITION:
BOTTOM: Time stamp appears at the bottom
TOP: Time stamp appears at the top
WATER MARK:
ON: Water mark appears on the picture when copying image
to CF card.
OFF: Water mark does not appear on the picture when
copying image to CF card.
WATER MARK POSITION:
BOTTOM: Water mark appears at the bottom
TOP: Water mark appears at the top.

4.8 System settings menu

SYSTEM SETTINGS MENU
PASSWORD ENABLE
PASSWORD
MULTIPLEXER
FIELD CODE LINE
DISK FULL
SPEED FORMAT
VIDEO SYSTEM
ERASE DISK
SYSTEM UPDATE
LOAD DEFAULT
CF FORMAT
MAIN MENU
PASSWORD ENABLE:
YES: PASSWORD required to enter the menu.
NO: PASSWORD not required to enter the menu.
PASSWORD :
Bosch Security Systems | 2004-11
720 X 576
ON
MULTIPLEXER: The following settings are available:
BOTTOM
ON
BOTTOM
>
PARAMETER PAIR:
NO
555555
Bosch LTC2600
FIELD CODE LINE:
13
REWRITE
BY IPS
PAL
DISK FULL:
>
>
>
SPEED FORMAT: Select recording speed by IPS (Images per
>
VIDEO SYSTEM: Select the video system NTSC or PAL (requires
>
When YES is set for PASSWORD ENABLE, a password is
required to enter the menu. The code is six digits long and
can be any digit from 1 to 5.
If you have activated the password, whenever you press the
menu button in live mode or stop button in record mode the
system asks you to enter the password. Therefore, be sure to
make a note of the password.
OFF: Select if only one camera is connected to the DVR. The
main monitor output is same as the video out connector all
the time.
MAKE OF MULTIPLEXER: Selection for various types of
multiplexer (e.g. BOSCH LTC2600). When a multiplexer is
selected, the video input from the MUX MAIN MONITOR
connector at the rear panel is looped through to the
MONITOR OUT when the recorder is not in MENU mode.
UNKNOWN: Select if your multiplexer is not listed and you
don't have a custom code.
CUSTOM: Select if you have a custom code for your
multiplexer model. Enter the parameters in the CUSTOM
MULTIPLEXER PARAMETER menu.
CUSTOM MULTIPLEXER MENU
PARAMETER PAIR 1 000
PARAMETER PAIR 2 000
PARAMETER PAIR 3 000
PARAMETER PAIR 4 000
PARAMETER PAIR 5 000
PARAMETER PAIR 6 000
PARAMETER PAIR 7 000
PARAMETER PAIR 8 000
SYSTEM SETTINGS MENU
In the CUSTOM MULTIPLEXER menu, you can fill-in a
custom code for a particular model of multiplexer. Consult
you sales representative for information on these codes.
If you set the multiplexer make to UNKNOWN, you can
adjust the field code line of the connected multiplexer
between 0 and 20. The default (13) is suitable for most
multiplexers. If the field code line appears at the top of the
playback channels, decrease the value. If multiplexers do not
playback correctly, increase the value.
STOP : When disk is full, the machine stops recording.
REWRITE : When disk is full, the current video overwrites the
existing video from the beginning of the hard disk.
second) or Hour
power reset to activate).
EN | 17
000
000
000
000
000
000
000
000
>