Installation; Figure 2. Typical System Application; Table 1. Compliance Codes - ADTRAN SHDSL E1 Installation And Maintenance Practice
Network terminating unit
Hide thumbs
Also See for SHDSL E1:
- Quick start manual (2 pages) ,
- Quick start manual (2 pages) ,
- Installation instructions (2 pages)
Table of Contents
Advertisement
Features
The features of the SHDSL T1/E1 NTU, P/N
1225236L1, include the following:
• Responds to an Embedded Operations Channel
(EOC) inventory response message
• Timing source is derived from the received SHDSL
network signal
• Local management access via VT100 menus
• Remote management access via EOC message
• Operates in T1 mode with a data rate of 200 kbps
to 1.544 Mbps and E1 mode with a data rate of
192 kbps to 2.048 Mbps
• Non-volatile memory configuration
• Factory default restoration via VT100 menu screens
or EOC messages
• Firmware upgrade using local management port or
remotely via EOC messages
• Password protection for local management access
and firmware upgrade
See
Figure 2
for a typical configuration setup.
Compliance
Table 1
shows the compliance codes for the SHDSL T1/
E1 NTU. The SHDSL T1/E1 NTU is NRTL listed to the
applicable UL standards. The SHDSL T1/E1 NTU is to
be installed in a restricted access location and in a Type
"B" or "E" enclosure only.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
Network
SCU
1181018L1
FSE
ALM
C
R
F
A
T
SCU
2
Management
System
VT100
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
LTU
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
1181308L1
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
2
O
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
3
R
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
MODE
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
SELECT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
OPT
HST
ACO
ACO
A
B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Total Access 3000
Figure 2. Typical System Application
Issue 1, August 2003
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Changes or modifications not expressly approved by
ADTRAN could void the user's authority to operate this
equipment.
Table 1. Compliance Codes
Code
Power Code (PC)
Telecommunication Code (TC)
Installation Code (IC)
3. INSTALLATION
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
After unpacking the SHDSL T1/E1 NTU, inspect it for
damage. If damage has occurred, file a claim with the
carrier, then contact ADTRAN Customer Service.
Refer to the
Warranty and Customer Service
further information. If possible, keep the original
shipping container for returning the SHDSL T1/E1
NTU for repair or for verification of shipping damage.
2-Wire Twisted Pair
LTU
1181308L1
PWR
1
P
2
O
R
3
T
4
OPT
SHDSL
SHDSL
T1/E1
T1/E1
LTU
NTU
Input
Output
F
C
–
X
A
–
section for
VT100
SHDSL
NTU
1225236L1
PWR
SHDSL
T1/E1
TEST
ALM
Customer T1 or E1
Equipment
(e.g., PABX)
61225236L1-5A
Advertisement
Table of Contents
