Strong Razor Series Installation Manual page 3

IMAGE
Screw
Spacer
Spacer
Spacer
Spacer
M6 Washer
M8 Washer
Hex Wrench
INSTALLATION:
Step 1: Mount the Wall Bracket Assembly
For Mounting on a Wood-Stud Wall
1. Pre-drill holes into two wood studs using a 3/32" drill bit.
Be sure to drill into the center of the studs at least 2-1/2"
deep. The use of a stud finder is highly recommended.
2. Insert four Lag Bolts (A) and Washer (B) into holes
through the Wall Plate and tighten down (Figure 1).
WARNING: Studs must be a minimum of 2"×4" and covered
with no more than 3/8" thick drywall.
WARNING: Tighten bolts so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage the bolts,
greatly reducing their holding strength.
For Mounting on a Concrete Wall
3. Pre-drill holes into concrete using 5/16" drill bits to a
depth of 2 -1/2". Insert concrete wall anchors (C) and tap
in with hammer, if necessary (Figure 2).
4. Insert four Lag Bolts (A) and Washers (B) into holes
through the Wall Plate and tighten (Figure 1).
WARNING: WARNING: When installing wall arm assembly on cinder When installing wall arm assembly on cinder
block, verify first that you have a minimum of 1-3/8" of concrete block, verify first that you have a minimum of 1-3/8" of concrete
thickness to be used for the concrete anchors. Do not drill into thickness to be used for the concrete anchors.
mortar joints! Be sure to mount in a solid part of the block, Be sure to mount in a solid part of the block,
mortar joints!
generally 1" minimum from the side of the block. Cinder block generally 1" minimum from the side of the block. Cinder block
must meet ASTM C-90 specifications. It is suggested that a must meet ASTM C-90 specifications. It is suggested that a
standard electric drill on slow setting is used to drill the hole standard electric drill on slow setting is used to drill the hole
instead of a hammer drill to avoid breaking out the back of the instead of a hammer drill to avoid breaking out the back of the
hole when entering a void or cavity. hole when entering a void or cavity.
CONCRETE CONCRETE must be 2500 psi density minimum. Lighter must be 2500 psi density minimum. Lighter
density concrete may not hold concrete anchor. density concrete may not hold concrete anchor. Make sure
that the supporting surface will safely support the combined load that the supporting surface will safely support the combined load
of the equipment and all attached hardware and components. of the equipment and all attached hardware and components.
5. Insert four Lag Bolts (A) into the wall anchors (C) through
the Wall Plate. Tighten all bolts.
WARNING: WARNING: Tighten bolts so that wall plate is firmly attached, Tighten bolts so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage the bolts, but do not overtighten. Overtightening can damage the bolts,
greatly reducing their holding strength. greatly reducing their holding strength.
www.snapav.com Support: 866.838.5052
DESCRIPTION
Do not drill into
Make sure
ITEM
(H) M8 × 50 mm
(I) 8.5 × 5 mm
(J) 8.5 × 10 mm
(K) 8.5 × 19 mm
(L) 8.5 × 22 mm
(M) 6.4 × 18 × 2 mm
(N) 8.4 × 20 × 2 mm
(O) M3 × 260 mm
Figure 1
Wall Plate
Figure 2
Drill holes and
insert anchors.
Place wall arm
assembly plate
over anchor and
secure with
lag bolt.
Tighten all
lag bolts.
Installation Manual
QUANTITY
4
4
4
4
4
8
8
1
Center of
Studs
Holes
Center hang hole
for easy wall
plate installation
Concrete
Wall
Wall Arm
Lag Bolt
3