Honda CB1000R 2015 Manual
  1. Manuals
  2. Brands
  3. Honda Manuals
  4. Motorcycle
  5. CB1000R 2015
  6. Manual

Honda CB1000R 2015 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Contents
P. 2
P. 16
P. 34
P. 85
P. 104
P. 127
P. 131

Advertisement

Table of Contents
loading

Related Manuals for Honda CB1000R 2015

Summary of Contents for Honda CB1000R 2015

  • Page 1: Table Of Contents

    Contents Motorcycle Safety P. 2 Operation Guide P. 16 Maintenance P. 34 Troubleshooting P. 85 Information P. 104 Specifications P. 127 Index P. 131...
  • Page 2 When service is required, remember that your Honda motorcycle. Your selection of a Honda dealer knows your motorcycle best. If Honda makes you part of a worldwide family you have the required mechanical “know- of satisfied customers who appreciate how” and tools, you can purchase an official Honda’s reputation for building quality into...
  • Page 3 A Few Words About Safety Your safety, and the safety of others, is very DANGER important. Operating this motorcycle safely is You WILL be KILLED or SERIOUSLY an important responsibility. HURT if you don’t follow instructions. To help you make informed decisions about safety, we have provided operating WARNING procedures and other information on safety...

  • Page 4: Motorcycle Safety

    Motorcycle Safety This section contains important information for safe riding of your motorcycle. Please read this section carefully. Safety Guidelines .........P. 3 Safety Labels ..........P. 7 Safety Precautions ........P. 9 Riding Precautions ........P. 10 Accessories & Modifications......P. 14 Loading ............P. 15...

  • Page 5: Safety Guidelines

    Safety Guidelines Safety Guidelines Before Riding Make sure that you are physically fit, mentally Follow these guidelines to enhance your safety: focused and free of alcohol and drugs. Check Perform all routine and regular inspections ● that you and your passenger are both wearing specified in this manual.
  • Page 6 Safety Guidelines We recommend that all riders take a certified Make Yourself Easy to See course approved by the Motorcycle Safety Make yourself more visible, especially at night, Foundation (MSF). New riders should start with by wearing bright reflective clothing, the basic course, and even experienced riders positioning yourself so other drivers can see will find the advanced course beneficial.
  • Page 7 Safety Guidelines check the tightness of critical nuts and bolts, Keep Your Honda in Safe Condition and check the handlebar, control levers, brakes, It’s important to keep your motorcycle properly and wheels. Ride slowly and cautiously. maintained and in safe riding condition.
  • Page 8 Safety Guidelines Carbon Monoxide Hazard Exhaust contains poisonous carbon monoxide, a colorless, odorless gas. Breathing carbon monoxide can cause loss of consciousness and may lead to death. If you run the engine in confined or even partly enclosed area, the air you breathe could contain a dangerous amount of carbon monoxide.

  • Page 9: Safety Labels

    Safety Labels Safety Labels hazards that could cause serious injury. Read these labels carefully and don’t remove them. Safety and information labels on your If a label comes off or becomes hard to read, motorcycle provide important safety contact your dealer for a replacement. information and may warn you of potential continued...
  • Page 10 Safety Labels...

  • Page 11: Safety Precautions

    Safety Precautions Safety Precautions Face shield with unobstructed field of vision ● or other approved eye protection Ride cautiously and keep your hands on the ● handlebar and feet on the footpegs. Look for a DOT (Department of Transportation) Keep passenger’s hands on the seat strap or certification label on any helmet you buy.

  • Page 12: Riding Precautions

    Riding Precautions ❙ Riding Precautions Boots or Riding Shoes Sturdy boots with non-slip soles and ankle protection Break-in Period ❙ During the first 300 miles (500 km) of running, Jacket and Pants follow these guidelines to ensure your Protective, highly visible, long-sleeved jacket motorcycle’s future reliability and performance.
  • Page 13 Riding Precautions ❙ Engine Braking Exercise caution on low traction surfaces. ● The tires slip more easily on such surfaces Engine braking helps slow your motorcycle and braking distances are longer. down when you release the throttle. For further Avoid continuous braking. slowing action, downshift to a lower gear.
  • Page 14 Riding Precautions ❙ Wet or Rainy Conditions To reduce the likelihood of theft, always lock ● Road surfaces are slippery when wet, and wet the handlebar and remove the key when brakes further reduce braking efficiency. leaving the motorcycle unattended. Exercise extra caution when braking in wet Use of an anti-theft device is also conditions.
  • Page 15 Riding Precautions Refueling and Fuel Guidelines Follow these guidelines to protect the engine and catalytic converter: Use only unleaded gasoline. ● Use recommended octane number. Using ● lower octane gasoline will result in decreased engine performance. Do not use fuels containing a high ●...

  • Page 16: Accessories & Modifications

    Honda or make modifications to your motorcycle from its Follow all instructions in this owner’s original design.

  • Page 17: Loading

    Loading Loading Carrying extra weight affects your ● motorcycle’s handling, braking and stability. Always ride at a safe speed for the load you are carrying. Avoid carrying an excessive load and keep ● within specified load limits. Maximum weight capacity P.

  • Page 18: Operation Guide

    Parts Location Fuel fill cap (P30) Throttle grip (P77) Front seat (P56) Front brake fluid reservoir (P70) Rear seat (P55) Front brake lever (P78) Engine oil fill cap (P60) Engine oil filter (P61) Engine oil drain bolt (P61) Engine oil level inspection window (P60) Rear brake Brake light switch...
  • Page 19 Front suspension spring preload/rebound damping (P79) Clutch lever (P78) Clutch fluid reservoir (P72) Left side cover (P57) Battery (P58) Fuse (P101) Coolant reservoir tank (P67) Air cleaner (P64) Crankcase breather (P66) Rear suspension spring preload (P82) Drive chain Shift lever (P74) (P29) Side stand...
  • Page 20 Instruments Adjust the Backlight Brightness (P20) Tachometer NOTICE Do not operate the engine in the tachometer red zone. Excessive engine speed can adversely affect engine life. Tachometer red zone (excessive engine rpm range) Clock (12-hour display) To set the clock: (P20) Odometer [TOTAL] &...
  • Page 21 Coolant temperature gauge ( Display Check Display range: 95 ºF (35 ºC) to 270 ºF (132 When the ignition switch is turned on, all ºC) the mode and digital segments will show, • Below 94 ºF (34 ºC): “ ” displays and the tachometer segment will •...
  • Page 22 Display Setting Setting Mode Following items to change sequentially (P21) • Backlight brightness adjustment • Clock setting • Changing of speed and mileage unit • Changing of coolant temperature gauge unit...
  • Page 23 Setting Mode 2 Clock setting: 1 Backlight brightness adjustment: Press RESET button until the desired hour is You can adjust the brightness to one of three displayed. levels. Press and hold RESET button to advance the hour fast. Turn the ignition switch to ON. Press and hold RESET button and SET button until the backlight brightness adjustment.
  • Page 24 Instruments (Continued) 3 Changing of speed and mileage unit: Press SET button. The speed and mileage unit is set, and then the display moves to the Press RESET button to select either “mph” changing of the coolant temperature gauge and “mile” or “km/h” and “km”. unit.
  • Page 25 4 Changing of coolant temperature gauge unit: Press RESET button to select “ºF” (Fahrenheit) or “ºC”(Centigrade). To end the selection and proceed to adjust the brightness of the display, press the SET button. The established setting can be set by pressing and holding the SET button and RESET button for more than 2 seconds, or turning the ignition switch to OFF.
  • Page 26 Indicators Low oil pressure indicator Comes on when the ignition switch is turned on. Goes off when the engine starts. If it comes on while engine is running: (P88) High coolant temperature indicator If it comes on while riding: (P87) PGM-FI (Programmed Fuel Injection) malfunction indicator lamp (MIL) Comes on briefly when the ignition switch is turned on...
  • Page 27 High beam indicator Right turn signal indicator Neutral indicator Comes on when the transmission Left turn signal indicator is in Neutral.
  • Page 28 Switches Engine stop switch Should normally remain in the position. In an emergency, switch to the Off position to stop the engine. Start button Horn button Turn signal switch Pressing the switch turns the turn signal off. Headlight dimmer switch •...
  • Page 29 Ignition Switch Turns electrical Switches the electrical system on/off, locks system on for the steering. starting/riding. Turns engine off. Key can be removed when in the OFF or LOCK position. LOCK Locks steering. ❙ Steering Lock Locking Lock the steering when parking to help Turn the handlebar all the way to the left.
  • Page 30 Starting the Engine Start your engine using the following Make sure the engine stop switch is in the position. procedure, regardless of whether the engine is cold or warm. Turn the ignition switch to the ON position. Shift the transmission to Neutral (N indicator comes on).
  • Page 31 Shifting Gears ❙ Your motorcycle transmission has 6 forward Recommended Shift Points gears in a one-down, five-up shift pattern. Shifting Up From 1st to 2nd 12 mph (20 km/h) From 2nd to 3rd 19 mph (30 km/h) From 3rd to 4th 25 mph (40 km/h) From 4th to 5th 31 mph (50 km/h)
  • Page 32 Refueling Opening the Fuel Fill Cap Fuel fill cap Filler neck plate Open the lock cover, insert the ignition key, and Ignition key turn it clockwise to open the fuel fill cap. Closing the Fuel Fill Cap After refueling, push the fuel fill cap closed until it locks.
  • Page 33 Storage Equipment A tool kit and helmet holders are located under the rear seat. There is also space to store a U- shaped lock. Document bag is located underside of the rear seat. The U-shaped lock is held in place above the Rear seat Document bag rear fender.
  • Page 34 Storage Equipment (Continued) WARNING Helmet holders Riding with a helmet attached to the holder can interfere with the rear wheel or suspension and could cause a crash in which you can be seriously hurt or killed. Use the helmet holder only while parked.
  • Page 35 The luggage tie-down hooks are located on the underside of the rear seat. Luggage tie-down hooks Rear seat Never use the tie-down hooks to tow or lift the motorcycle.

  • Page 36: Maintenance

    Please read “Importance of Maintenance” and “Maintenance Fundamentals” carefully before attempting any maintenance. Refer to “Specifications” for service data. An optional larger tool kit may be available. Check with your Honda dealer’s parts department. Importance of Maintenance ......P. 35 Coolant ............P. 67 Maintenance Schedule.......P.

  • Page 37: Importance Of Maintenance

    Importance of Maintenance For information about the exhaust emission and Importance of Maintenance noise emission requirements of the U.S. Keeping your motorcycle well-maintained is Environmental Protection Agency (EPA) and the absolutely essential to your safety and to California Air Resources Board (CARB). P.
  • Page 38 Importance of Maintenance Maintenance Safety Always read the maintenance instructions before you begin each task, and make sure that you have the tools, parts, and skills required. We cannot warn you of every conceivable hazard that can arise in performing maintenance.

  • Page 39: Maintenance Schedule

    If you sell the motorcycle, these receipts should be transferred with the Maintenance work should be performed in motorcycle to the new owner. accordance with Honda’s standards and specifications by properly trained and equipped technicians. Your dealer meets all of these requirements. Keep an accurate record of maintenance to help ensure that your motorcycle is properly maintained.
  • Page 40 : Intermediate. We recommend service by your dealer, unless you : Technical. In the interest of safety, have your motorcycle have the necessary tools and are mechanically skilled. serviced by your dealer. Procedures are provided in an official Honda Service Manual 121).
  • Page 41 Maintenance Schedule Frequency Odometer Reading × 1,000 mi Refer to page Items × 1,000 km 12.8 19.2 25.6 32.0 38.4 Drive chain Every 500 mi (800 km): Brake Fluid Brake Pads Wear Brake System Brake Light Switch – Headlight Aim –...

  • Page 42: Maintenance Fundamentals

    Maintenance Fundamentals Suspension spring preload and damper Pre-ride Inspection ● settings are adjusted to suit load. To ensure safety, it is your responsibility to perform a pre-ride inspection and make sure Check the following items after you get on your that any problem you find is corrected.
  • Page 43 Maintenance Fundamentals Periodic Checks You should also perform other periodic maintenance checks at least once a month regardless of how often you ride, or more often if you ride frequently. Also, check the odometer reading against the Maintenance Schedule and perform all maintenance that is due.
  • Page 44 Maintenance Fundamentals Replacing Parts WARNING Always use Honda Genuine Parts or their Installing non-Honda parts may make equivalents to ensure reliability and safety. your motorcycle unsafe and cause a crash in which you can be seriously When ordering colored components, specify hurt or killed.
  • Page 45 Maintenance Fundamentals Electrolyte splashes into your mouth: Battery ● Rinse mouth thoroughly with water, and Your motorcycle has a maintenance-free type do not swallow. battery. You do not have to check the battery WARNING electrolyte level or add distilled water. Clean the battery terminals if they become dirty or The battery gives off explosive corroded.
  • Page 46 30 days using a charger designed specifically for 3. If the terminals are heavily corroded, clean your Honda, which can be purchased from your and polish the terminals with a wire brush or dealer. Read the information that came with sandpaper.
  • Page 47 Bump starting is also not recommended. NOTICE Installing non-Honda electrical accessories can overload NOTICE the electrical system, discharging the battery and possibly Replacing a fuse with one that has a higher rating greatly damaging the system.
  • Page 48 Selecting the Engine Oil circular API service symbol. For recommended engine oil, see “Specifications.” P. 128 If you use non-Honda engine oil, check the label to make sure that the oil satisfies all of the following standards: JASO T 903 standard : MA ●...
  • Page 49 O-rings, or kinks, have the chain Recommended brake fluid: inspected by your dealer. Honda DOT 4 Brake Fluid or equivalent Also inspect the front sprocket and rear wheel sprocket. If either has worn or damaged teeth, have the sprocket replaced by your dealer.
  • Page 50 Use a soft brush if the chain is dirty. Normal Worn Damaged (GOOD) (REPLACE) (REPLACE) After cleaning, wipe dry and lubricate with the recommended lubricant. Recommended lubricant: NOTICE Pro Honda HP Chain Lube or equivalent. User of a new chain with worn sprockets will cause rapid chain wear.
  • Page 51 Avoid getting lubricant on the brakes or tires. Avoid applying excess chain lubricant to prevent spray onto your clothes and the motorcycle. Recommended Coolant Pro Honda HP coolant is a pre-mixed solution of antifreeze and distilled water. Concentration: 50% antifreeze and 50% distilled water...
  • Page 52 Maintenance Fundamentals ❙ Inspecting for Abnormal Wear Tires (Inspecting/Replacing) Inspect the tires for ❙ Checking the Air Pressure signs of abnormal Visually inspect your tires and use an air wear on the contact pressure gauge to measure the air pressure at surface.
  • Page 53 Maintenance Fundamentals ❙ Inspecting Tread Depth WARNING Inspect the tread wear indicators. If they become visible, replace the tires immediately. Riding on tires that are excessively For your safety, you should replace the tires worn or improperly inflated can cause when the minimum tread depth is reached.
  • Page 54 Always use the size and type of tires Have the wheel balanced with Honda ● recommended in this owner’s manual. Genuine balance weights or equivalents after the tire is installed.
  • Page 55 Maintenance Fundamentals ❙ Tire Identification Number (TIN) Tire Service Life The tire identification number (TIN) is a group of The service life of your tires is dependent on numbers and letters located on the sidewall of many factors, including, but not limited to, the tire.
  • Page 56 Maintenance Fundamentals Crankcase Breather Service more frequently when riding in rain, at full throttle, or after the motorcycle is washed or overturned. Service if the deposit level can be seen in the transparent section of the drain tube. If the drain tube overflows, the air filter may become contaminated with engine oil causing poor engine performance.

  • Page 57: Removing & Installing Body Components

    Removing & Installing Body Components ❙ Rear Seat Removal 1. Insert the ignition key into the seat lock, and turn and hold the key clockwise to Prongs Rear seat unlock the rear seat. 2. Pull the rear of the rear seat back and up. ❙...

  • Page 58: Front Seat

    Removing & Installing Body Components Front Seat ❙ Front Seat Removal 1. Remove the rear seat. P. 55 2. Remove the bolt. Front seat Bolt 3. Pull the front seat back and up. Prongs ❙ Installation 1. Install the prongs into the front seat stays. 2.

  • Page 59: Left Side Cover

    Removing & Installing Body Components Left Side Cover ❙ Left Side Cover Removal 1. Remove the rear seat and front seat. The left side cover must be removed to service the air cleaner and crankcase 2. Remove the bolt. breather. 3.

  • Page 60: Clips

    Removing & Installing Body Components Clips Clips Battery The clips must be removed to remove the Positive terminal Rubber strap inner cover. ❙ Removal 1. Press down on the center pin to release the lock. 2. Pull the clip out of the hole. Center ❙...
  • Page 61 Removing & Installing Body Components Battery ❙ ❙ Removal Installation Make sure the ignition switch is off. Install the parts in the reverse order of removal. Always connect the positive 1. Remove the rear seat and front seat. terminal first. Make sure that bolts and nuts are tight.

  • Page 62: Engine Oil

    Engine Oil Checking the Engine Oil Oil fill cap 1. If the engine is cold, idle the engine for 3 to 5 minutes. 2. Turn the ignition switch off and wait for 2 to 3 minutes. Oil level inspection 3. Place your motorcycle in an upright window position on a firm, level surface.
  • Page 63 We recommend that you have your oil filler opening. motorcycle serviced by your dealer. Wipe up any spills immediately. Use a new Honda Genuine oil filter or equivalent specified for your model. NOTICE Using the wrong oil filter can result in serious damage to the engine.
  • Page 64 Engine Oil Changing Engine Oil & Filter 1. If the engine is cold, idle the engine for 3 6. Remove the oil filter guard by removing to 5 minutes. the bolts and washers. 2. Turn the ignition switch off and wait for 7.
  • Page 65 Engine Oil Changing Engine Oil & Filter 8. Apply a thin coat of engine oil to the 14. Install the parts in the reverse order of rubber seal of a new oil filter. removal. 9. Install the new oil filter and tighten. Torque: 19 lbf·ft (26 N·m, 2.7 kgf·m).

  • Page 66: Air Cleaner

    Air Cleaner Inspecting & Changing Air Air cleaner cover Cleaner Element Use a new Honda Genuine air cleaner element or equivalent specified for your motorcycle. NOTICE Using the wrong air cleaner element can result in serious damage to the engine.
  • Page 67 Air Cleaner Inspecting & Changing Air Cleaner Element 4. Remove the screws and air cleaner housing cover. 5. Pull out the air cleaner element and check it for any damage. Blow away the remaining dust by applying compressed air from the outside of the air cleaner element.

  • Page 68: Crankcase Breather

    Crankcase Breather Cleaning the Crankcase Crankcase Breather breather tube 1. Remove the rear seat and front seat. 2. Remove the left side cover. P. 57 3. Remove the air cleaner cover. P. 64 4. Remove the crankcase breather tube. 5. Drain deposits into a suitable container. 6.

  • Page 69: Coolant

    Coolant Checking the Coolant If the coolant level is dropping noticeably or the reserve tank is empty, you likely have a 1. Place your motorcycle on a firm, level serious leak. Have your motorcycle inspected surface. by your dealer. 2. Hold your motorcycle in an upright position.
  • Page 70 Coolant Adding Coolant Adding Coolant Clips Inner cover If the coolant level is below the LOWER level Reserve tank cap mark, add the recommended coolant 49) until the level reaches the UPPER level mark. Add fluid only from the reserve tank cap and do not remove the radiator cap.
  • Page 71 Coolant Changing Coolant Changing Coolant 4. Install the parts in the reverse order of removal. Have your dealer change the coolant unless WARNING you have the proper tools and are mechanically qualified. Removing the radiator cap while the engine is hot can cause the coolant to spray out, potentially scalding you.

  • Page 72: Brakes/Clutch

    Brakes/Clutch Checking Brake Fluid If the brake fluid level in either reservoir is below the LOWER level mark or the brake 1. Place your motorcycle in an upright lever and pedal freeplay becomes excessive, position on a firm, level surface. inspect the brake pads for wear.
  • Page 73 Brakes/Clutch Inspecting the Brake Pads Inspecting the Brake Pads Inspect the brake pads from the Rear rear left of the motorcycle. Check the condition of the brake pad wear Rear Brake pads indicators. The pads need to be replaced if a brake pad is worn to the bottom of the indicator.
  • Page 74 Brakes/Clutch Checking Clutch Fluid Checking Clutch Fluid If the fluid level is low or if you find fluid leaks, or deterioration or cracks in the hoses and fittings, have the clutch system serviced Clutch fluid reservoir by your dealer. UPPER level mark LOWER level mark 1.

  • Page 75: Side Stand

    Side Stand 4. Start the engine, pull the clutch lever in, and shift the transmission into gear. 5. Lower the side stand all the way. The engine should stop as you lower the side stand. If the engine doesn’t stop, have your motorcycle inspected by your dealer.

  • Page 76: Drive Chain

    Drive Chain Inspecting the Drive Chain Slack Check the drive chain slack at several points along the chain. If the slack is not constant at all points, some links may be kinked and binding. Have the chain inspected by your dealer. 1.
  • Page 77 Drive Chain Adjusting the Drive Chain Slack Adjusting the Drive Chain Slack 5. Tighten the bearing holder pinch bolt to the specified torque. Adjusting the chain requires special tools. Torque: 65 lbf·ft (88 N·m, 9.0 kgf·m). Have the drive chain slack adjusted by your dealer.
  • Page 78 Drive Chain Checking the Drive Chain Wear Checking the Drive Chain Wear 6. Check drive chain slack. P. 74 Bearing holder Bearing holder Check the chain wear label when adjusting pinch bolt the drive chain. If the red zone on the label aligns with the index mark after the chain has been adjusted to the proper slack, the chain is excessively worn and must be replaced.

  • Page 79: Throttle

    Throttle Checking the Throttle Adjusting the Throttle Cable Freeplay With the engine off, check that the throttle rotates smoothly from fully closed to fully 1. Slide the cable boot off the adjuster. open in all steering positions and throttle 2. Loosen the lock nut. freeplay is correct.

  • Page 80: Other Adjustments

    Other Adjustments ❙ Adjusting the Clutch and Brake Adjustment method Levers Turn the adjuster until the numbers align with the index mark while pushing the lever You can adjust the distances between the tip forward in the desired position. of the clutch lever and handle grip, and between the tip of the brake lever and After adjustment, check that the levers handle grip.

  • Page 81: Front Suspension

    Other Adjustments Adjusting the Front Suspension Adjusting the Front Suspension ❙ Spring Preload You can adjust the spring preload by turning the adjuster to suit the load or the road surface. Turn clockwise to increase spring preload (hard), or turn counterclockwise to decrease spring preload (soft).
  • Page 82 Other Adjustments Adjusting the Front Suspension ❙ Rebound Damping You can adjust the rebound damping by turning the adjuster to suit the load or the road surface. Turn clockwise to increase rebound damping (hard), or turn counterclockwise to decrease rebound damping (soft). The standard position is approximately 2 turns from the Reference punch...
  • Page 83 Other Adjustments Adjusting the Front Suspension ❙ Compression Damping Adjuster You can adjust the compression damping by the adjuster to suit the load or the road surface. Turn clockwise to increase compression damping (hard), or turn counterclockwise to decrease compression damping (soft).

  • Page 84: Rear Suspension

    Other Adjustments Adjusting the Rear Suspension Adjusting the Rear Suspension Cloth 1 2 3 4 5 6 7 8 9 10 Adjusting the suspension requires pin spanner. We recommend that you have your motorcycle serviced by your dealer. ❙ Spring Preload You can adjust the spring preload by the Adjuster adjuster to suit the load or the road surface.
  • Page 85 Other Adjustments Adjusting the Rear Suspension ❙ Rebound Damping Adjuster You can adjust the rebound damping by turning the adjuster to suit the load or the road surface. Turn clockwise to increase rebound damping (hard), or turn counterclockwise to decrease rebound damping (soft).

  • Page 86: Headlight Aim

    Other Adjustments Adjusting the Brake Light Switch Adjusting the Brake Light Adjusting the Headlight Aim Switch You can adjust vertical aim of the headlight for proper alignment. Turn the screw using a Check the operation of the brake light Phillips screwdriver in or out as necessary. switch.

  • Page 87: Troubleshooting

    Troubleshooting Engine Will Not Start......... P. 86 Tire Puncture ..........P. 89 Overheating (High coolant temperature Electrical Trouble........P. 97 indicator is on) ......... P. 87 Battery Goes Dead ........P. 97 Warning Indicators On or Flashing ..P. 88 Burned-out Light Bulb .......P. 97 Low Oil Pressure Indicator ......

  • Page 88: Engine Will Not Start

    Engine Will Not Start ❙ ❙ Starter Motor Operates But Engine Starter Motor Does Not Operate Does Not Start Check the following items: Check the following items: Make sure engine stop switch is Run ● Check the correct engine starting position.

  • Page 89: Overheating (High Coolant Temperature Indicator Is On)

    Overheating (High coolant temperature indicator is on) The engine is overheating when the 2. Check that the radiator fan is operating, following occurs: and then turn the ignition switch to the High coolant temperature indicator comes OFF position. ● If the fan is not operating: Acceleration becomes sluggish.

  • Page 90: Warning Indicators On Or Flashing

    Warning Indicators On or Flashing Low Oil Pressure Indicator If the engine oil level goes down rapidly, your motorcycle may have a leak or another If the low oil pressure indicator comes on, serious problem. Have your motorcycle pull safely to the side of the road and stop inspected by your dealer.

  • Page 91: Tire Puncture

    Tire Puncture Repairing a puncture or removing a wheel WARNING requires special tools and technical expertise. We recommend you have this type of service Riding your motorcycle with a performed by your dealer. temporary tire repair can be risky. If After an emergency repair, always have the the temporary repair fails, you can tire inspected/replaced by your dealer.
  • Page 92 Tire Puncture Removing Wheels ❙ Front Wheel 3. On the left side, remove the mounting bolts and remove the brake caliper. Removal 4. On the right side, remove the mounting 1. Park on a firm, level surface. bolts and remove the brake caliper. 2.
  • Page 93 Tire Puncture Removing Wheels 5. Loosen the right and left axle pinch bolts. Installation 6. Remove the front axle bolt. 1. Attach the side collars to the wheel. 7. Support your motorcycle securely and 2. On the left side, place the wheel raise the front wheel off the ground using between the fork legs and insert the a maintenance stand or a hoist.
  • Page 94 Tire Puncture Removing Wheels 4. Tighten the left axle pinch bolt to hold Front fork spacers the axle. 5. Tighten the axle bolt. End of front axle shaft Torque: 44 lbf·ft (59 N·m, 6.0 kgf·m). 6. Loosen the left axle pinch bolt. 7.
  • Page 95 Tire Puncture Removing Wheels 10. Install the left brake caliper and tighten 13. Retighten the left axle pinch bolt. the mounting bolts. Torque: 16 lbf·ft (22 N·m, 2.2 kgf·m). Torque: 33 lbf·ft (45 N·m, 4.6 kgf·m). 14. Raise the front wheel off the ground Take care to prevent the brake caliper again, and check that the wheel rotates from scratching the wheel during...
  • Page 96 Tire Puncture Removing Wheels ❙ Rear Wheel 2. Loosen the muffler band bolt. Removal 1. Support your motorcycle securely and raise the rear wheel off the ground using a maintenance stand or a hoist. Muffler band bolt...
  • Page 97 Tire Puncture Removing Wheels 3. Remove the muffler mount bolt A, B and 5. Remove the rear wheel nuts, and remove nut. the rear wheel. 4. Remove the muffler. Rear wheel nuts Muffler mount Rear bolt B wheel Muffler mount nut Muffler Rear wheel nuts Muffler mount bolt A...
  • Page 98 Tire Puncture Removing Wheels Installation If a torque wrench was not used for 1. To install the rear wheel, reverse the installation, see your dealer as soon as removal procedure. possible to verify proper assembly. 2. Install the rear wheel and tighten the rear Improper assembly may lead to loss of wheel nuts equally.

  • Page 99: Electrical Trouble

    Electrical Trouble Battery Goes Dead Burned-out Light Bulb Charge the battery using a motorcycle Follow the procedure below to replace a battery charger. burned-out light bulb. Remove the battery from the motorcycle Turn the ignition switch to the OFF or LOCK before charging.
  • Page 100 Electrical Trouble Burned-out Light Bulb ❙ Headlight Bulb 5. Install a new bulb and parts in the reverse order of removal. 1. Remove the front visor by removing the Make sure the tab on the dust cover is bolts. upper. Front visor Headlight Bulb holder...
  • Page 101 Electrical Trouble Burned-out Light Bulb ❙ ❙ Position Light Brake/Tail Light Brake/Tail light Position light The brake and tail light uses several LEDs. If there is a LED which is not turned on, see The position light uses several LEDs. your dealer for this service.
  • Page 102 Electrical Trouble Burned-out Light Bulb ❙ ❙ Front/Rear Turn Signal Bulb License Plate Light Bulb 1. Remove the screw. 1. Remove the screws, license light cover 2. Remove the turn signal lens and lens and license light cover packing. packing. 2.

  • Page 103: Blown Fuse

    Electrical Trouble Blown Fuse ❙ Blown Fuse Fuse Box Fuses Fuse box cover Before handling fuses, see “Inspecting and Replacing Fuses.” P. 45 Spare fuses continued...
  • Page 104 Electrical Trouble Blown Fuse ❙ Fuse Holder Fuses 1. Remove the rear seat and front seat. Starter magnetic switch cover 2. Remove the fuse box cover. 3. Pull the fuses out one by one with the fuse puller in the tool kit and check for a blown fuse.
  • Page 105 Electrical Trouble Blown Fuse 3. Pull the main fuse and FI fuse out one by one. Check for a blown fuse. Always replace a blown fuse with a spare of the same rating. Spare fuses are provided in the fuse box.

  • Page 106: Information

    Information Keys............P. 105 Honda Contacts ........P. 124 Instruments, Controls, & Other Features ... P. 106 Reporting Safety Defects ......P. 126 Caring for Your Motorcycle.....P. 107 Storing Your Motorcycle ......P. 110 Transporting Your Motorcycle ....P. 111 You & the Environment ......P. 112 Vehicle Identification Number ....P.

  • Page 107: Keys

    Keys Keys Ignition key Be sure to record the key number provided with the key number plate. Store the spare key and recorded key number in a safe location. To make a duplicate, take the spare key or the key number to your dealer. If you lose all keys and the key number, the ignition switch assembly will probably have to be removed by your dealer to determine the key...

  • Page 108: Instruments, Controls, & Other Features

    Instruments, Controls, & Other Features Instruments, Controls, & exceeds 999,999. Other Features Tripmeter Ignition Switch The tripmeter A, B returns to 0.0 when the read-out exceeds 999.9. The headlight is always on when the ignition switch is ON. Leaving the ignition switch ON with the engine stopped will drain the battery.

  • Page 109: Caring For Your Motorcycle

    Frequent cleaning and polishing is important to 3. Thoroughly rinse your motorcycle with plenty ensure the life of your Honda. A clean of clean water and dry with soft, clean cloth. motorcycle makes it easier to spot potential 4.
  • Page 110 Caring for Your Motorcycle ❙ Washing Precautions Do not direct water near the headlight: ● Follow these guidelines when washing: Any condensation inside the headlight Do not use high-pressure washers: should dissipate after a few minutes of ● High-pressure water cleaners can damage running the engine.
  • Page 111 Caring for Your Motorcycle When the exhaust pipe and muffler are painted, Panels do not use a commercially available abrasive Follow these guidelines to prevent scratches kitchen cleaning compound. Use a neutral and blemishes: detergent to clean the painted surface on the Wash gently using a soft sponge and plenty ●...

  • Page 112: Storing Your Motorcycle

    For more information about storage, refer to If you won’t be riding for an extended period, the Honda Winter Storage Guide, available follow these guidelines: from your dealer. Wash your motorcycle and wax all painted ●...

  • Page 113: Transporting Your Motorcycle

    Transporting Your Motorcycle Transporting Your Motorcycle If your motorcycle needs to be transported, it should be carried on a motorcycle trailer or a flatbed truck or trailer that has a loading ramp or lifting platform, and motorcycle tie-down straps. Never try to tow your motorcycle with a wheel or wheels on the ground.

  • Page 114: You & The Environment

    You & the Environment You & the Environment drain or on the ground. Used oil, gasoline, coolant, and cleaning solvents contain poisons Owning and riding a motorcycle can be that can hurt refuse workers and contaminate enjoyable, but you must do your part to protect drinking water, lakes, rivers, and oceans.

  • Page 115: Vehicle Identification Number

    Vehicle Identification Number Vehicle Identification Number The VIN and engine serial numbers uniquely identify your motorcycle and are required in order to register your motorcycle. They may also be required when ordering replacement parts. The VIN is stamped on the right side of the steering head and also appears on the Safety Certification Label attached to the left side of the frame.

  • Page 116: Emission Control Systems

    Emission Control Systems Emission Control Systems Your motorcycle engine emits combustion by products, including carbon monoxide (CO), oxides of nitrogen (NOx), and hydrocarbons (HC). Gasoline evaporation also emits hydrocarbons. Controlling the production of NOx, CO, and HC is important for the environment.
  • Page 117 Compliance with the terms of the Distributor’s The EPA requires that motorcycles built after Warranties for Honda Motorcycle Emission January 1, 1983 comply with applicable noise Control Systems is necessary in order to emission standards for one year or 3,730 miles maintain a valid emissions system warranty.
  • Page 118 Emission Control Systems ❙ Secondary Air Injection System Exhaust Emission Control System The secondary air injection system adds filtered The exhaust emission control system includes air into the exhaust gas to help improve the following components that should not need emission control performance.
  • Page 119 Emission Control Systems Crankcase Emissions Control System Noise Emission Control System ❙ TAMPERING WITH THE NOISE CONTROL The positive crankcase ventilation system SYSTEM IS PROHIBITED: prevents gases that build up in the engine’s crankcase from being released into the U. S. federal law prohibits the following acts or atmosphere.
  • Page 120 Emission Control Systems ❙ AMONG THOSE ACTS PRESUMED TO Problems Affecting Motorcycle Exhaust CONSTITUTE TAMPERING ARE THE Emissions FOLLOWING ACTS: Have your motorcycle inspected and repaired by Removal of, or puncturing the muffler, ● your dealer if you experience any of the baffles, header pipes or any other component following symptoms: which conducts exhaust gases.

  • Page 121: Catalytic Converter

    A defective catalytic converter contributes to air riding and turn off the engine. Have your pollution and can impair your engine’s motorcycle serviced as soon as possible. performance. A replacement unit must be an original Honda part or equivalent.

  • Page 122: Oxygenated Fuels

    Oxygenated Fuels Oxygenated Fuels If you accidentally fill your fuel tank with an oxygenated fuel containing higher percentages, Some conventional fuels blended with alcohol you may experience performance problems. To or an ether compound are available in some resolve the problem, have your dealer drain the areas to help reduce emissions to meet clean air fuel tank and replace with the correct fuel.

  • Page 123: Authorized Manuals

    The Service Manual used by your authorized These Honda manuals are written for the dealer is available from your Honda dealer or professional technician. However, if you possess Helm, Inc. the proper tools, observe the safety standards,...

  • Page 124: Warranty Coverage And Service

    Honda. Your warranty coverage does not apply to the normal wear Coverage and deterioration associated with use of the motorcycle. Your new Honda is covered by the following warranties: Your warranty coverage is not voided if you Motorcycle Limited Warranty ●...
  • Page 125 If you believe you have a problem with your dealership or their designated representative. motorcycle, call the service department of your Honda dealer. Make an appointment for an inspection and diagnosis. You will be asked to authorize that inspection, and your dealer will return the results of the inspection.

  • Page 126: Honda Contacts

    Dealer name and address ● motorcycle or with your dealer, please send your comments to the following address: We will likely ask your Honda dealer to respond, Motorcycle Division, or possibly acknowledge your comments American Honda Motor Co., Inc., directly.
  • Page 127 Honda Contacts Your Honda Dealer Honda Rider’s Club of America (HRCA) The service department of your Honda dealer The Honda Rider’s Club of America (HRCA) offers trained personnel to perform regular sponsors local riding chapters at Authorized maintenance and most repairs. It has the latest Honda Dealerships across the country.

  • Page 128: Reporting Safety Defects

    Highway Traffic Safety Administration Administrator, NHTSA, (NHTSA) in addition to notifying 1200 New Jersey Avenue, SE., American Honda Motor Co., Inc. Washington, DC 20590. You can also obtain other information If NHTSA receives similar complaints, it about motor vehicle safety from: may open an investigation, and if it finds http://www.safercar.gov...

  • Page 129: Specifications

    Specifications Specifications ■ Main Components Unleaded gasoline Type SC60 Fuel Recommended fuel octane number: Pump Octane Number (PON) 86 or higher. Overall length 83.5 in (2,120 mm) Tank capacity 4.5 US gal (17 liters) Overall width 31.7 in (805 mm) Battery YTZ10S 12V-8.6Ah (10HR) Overall height...
  • Page 130 API Service Classification SG or higher except oils labeled as energy conserving or resource Recommended conserving on the circular API service label, engine oil SAE 10W-30, JASO T 903 standard MA, Pro Honda GN4 4-stroke oil or Honda 4-stroke oil or an equivalent motorcycle oil...
  • Page 131 Specifications ■ ■ Bulbs Torque Specifications Headlight 12V-60/55W Engine oil drain bolt 22 lbf·ft (30 N·m, 3.1 kgf·m) Brake light Oil filter 19 lbf·ft (26 N·m, 2.7 kgf·m) Taillight Bearing holder pinch bolt 65 lbf·ft (88 N·m, 9.0 kgf·m) Front turn signal lights 12V-21/5W x 2 Front wheel axle bolt 44 lbf·ft (59 N·m, 6.0 kgf·m)
  • Page 132 Information Record Engine No. Color Label & Code Owner’s Name Address City/State Phone Dealer’s Name Address City/State Phone Service Manager...

  • Page 133: Index

    Index Index Owner’s Manual........31 Accessories..........14 Coolant ............67 Air cleaner ..........64 Crankcase Breather ........66 Authorized Manuals ....... 121 Digital Clock Adjustment......20 Battery ..........43, 58 Display Setting........... 20 Brakes Drive Chain .......... 47, 74 Brake Light Switch ........84 Fluid...........
  • Page 134 Headlight Aim ........... 84 Luggage Tie-Down Hooks......33 Headlight Dimmer Switch......26 Helmet Holder ........31, 32 High Beam Indicator ......... 25 Maintenance High Coolant Temperature Indicator. 24, 87 Fundamentals ...........40 Honda Contacts ........124 Importance ..........35 Horn Button..........26 Safety ............36 Schedule...........37...
  • Page 135 Recommended Maximum Weight Limit......15 Modifications ..........14 Fuel ............30 Oil ............46 Refueling ........... 30 Neutral Indicator........25 Removal Battery ............. 58 Clips............58 Odometer .......... 18, 106 Front Seat..........56 Left Side Cover ......... 57 Engine ..........46, 60 Rear Seat..........
  • Page 136 Start Button ..........26 Starting the Engine ........28 Vehicle Identification Number....113 Steering Lock ..........27 Stopping Engine........106 Storage Warning Indicators On ......88 Warranty Coverage and Service .....122 Compartment........... 31 Owner’s Manual........31 Washing Your Motorcycle.......107 Storing Your Motorcycle......110 Weight Limit ........15, 127 Switches .............

This manual is also suitable for:

Cb1000ra 2015

Table of Contents