Advertisement
Quick Links
ROLAND AIRA TB-3 EFFECTS PARAMETER GUIDE
[dedicated FX section]
1.
DISTORTION SW
2.
TYPE
[all effects have two copies except where noted]
DISTORTION
PITCH SHIFTER
REVERB
COMPRESSOR
RING MODULATOR
BIT CRUSHER
TREMOLO
CHORUS
FLANGER
PHASER
DELAY
(0 -1)
OFF, ON
(0 - 24)
Mid Boost
Clean Boost
Treble Boost
Blues OD
Crunch
Natural OD
/
EQUALIZER
DISTORTION
Switches distortion on/off.This is a mono effect.
This is a booster with unique characteristics in the
midrange.
This not only functions as a booster, but also
produces a clean tone that has punch even when
used alone.
This is a booster that has bright characteristics.
This is a crunch sound of the BOSS BD-2. This
produces distortion that faithfully reproduces the
nuances of picking.
A lustrous crunch sound with an added element of
amp distortion.
This is an overdrive sound that provides distortion
with a natural feeling.
This models the sound of the BOSS OD-1. This
OD-1
produces sweet, mild distortion.
Advertisement
Related Manuals for Roland AIRA TB-3
Summary of Contents for Roland AIRA TB-3
- Page 1 ROLAND AIRA TB-3 EFFECTS PARAMETER GUIDE [all effects have two copies except where noted] DISTORTION PITCH SHIFTER EQUALIZER REVERB COMPRESSOR RING MODULATOR BIT CRUSHER TREMOLO CHORUS FLANGER PHASER DELAY [dedicated FX section] DISTORTION DISTORTION SW (0 -1) OFF, ON Switches distortion on/off.This is a mono effect.
- Page 2 T-Scream This models an Ibanez TS-808. Turbo OD This is the high-gain overdrive of the BOSS OD-2. Warm OD This is a warm overdrive. Distortion This gives a basic, traditional distortion sound. Mild DS Mid DS This models a Proco RAT. GUV DS This models a Marshall GUV’...
-
Page 3: [Ps] Pitch Shifter
[FX1 only] [PS] PITCH SHIFTER PS SW (0 -1) OFF, ON Switches pitch shifter on/off. This is a mono/stereo effect. One-voice pitch-shifted sound output in mono. Pitch 2 1MONO is disabled in this mode. Two-voice pitch-shifted sound (1:PITCH, 2:PITCH) 2MONO PS VOICE (0 - 2) output in mono. -
Page 4: Eq (Equalizer)
[FX1 only] [EQ] EQUALIZER EQ SW (0 -1) OFF, ON Switches equalizer on/off. This is a mono effect. This sets the frequency at which the low cut filter EQ LOW CUT (0 - 17) Flat – 800Hz begins to take effect. When “FLAT” is selected, the low cut filter will have no effect. - Page 5 [FX2 only] [RV] REVERB RV SW (0 -1) OFF, ON Switches reverb on/off. This is a stereo effect. If time and predelay are set to 0, gives a nice doubling effect with more bass at one end and AMBIENCE phasing effect with less low end on the other. Metallic overtones at low reverb times.
-
Page 6: [Rm] Ring Modulator
[CS] COMPRESSOR CS SW (0 -1) OFF, ON Switches compressor on/off. This is a mono effect. CS ATTACK (0 - 124) 0 – 800ms Adjusts the compressor attack time. CS RELEASE (0 - 124) 0 – 8000ms Adjusts the compressor release time. Adjusts the threshold at which the compressor is CS THRESHOLD (0 - 40) - Page 7 [BC] BIT CRUSHER BC SW (0 -1) OFF, ON Switches bit crusher on/off. This is a mono effect. BC FILTER (0 - 127) Adjusts the bit crusher LPF cutoff frequency. BC SAMPLE RATE (0 - 127) Adjusts the sample rate (higher values = lower sample rates). BC EQ LOW (0 - 30) -15dB –...
- Page 8 [CH] CHORUS CH SW (0 -1) OFF, ON Switches chorus on/off. This is a mono/stereo effect. This chorus effect outputs the same sound from both L MONO channel and R channel. This is a stereo chorus effect that adds different chorus STEREO1 sounds to L channel and R channel.
- Page 9 [PH] PHASER PH SW (0 -1) OFF, ON Switches phaser on/off. This is a mono effect. This is a four-phase effect. A light phaser effect is 4Stage obtained. This is a eight-phase effect. It is a popular phaser 8Stage effect. PH TYPE (0 - 3) This is a twelve-phase effect.
- Page 10 DD EFFECT LEVEL (0 - 100) Adjusts the volume of the delay effect. DD DIRECT LEVEL (0 -100) Adjusts the volume of the direct sound. Resources Used: parameter guides for Roland • ◦ [RD-2000] ◦ [MS-3] ◦ [GT-01] ◦ [GT-100] ◦...