Advertisement
CLEI Code
Part Number
Serial Number
To/from SCU menus
1. Configuration
Code Version
Code Checksum
Boot Version
Boot Checksum
Self Test
2. Provisioning
3. Status
4. Test
1. DS3 Statistics
5. Performance Monitoring
2. T1/E1 Statistics
3. Clear ALL Statistics
Note: An asterisk (*) indicates default setting
Warranty:ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service.
MX2820 –48 VDC M13 MUX
1. C-BIT
1. DS3 Framing
2. M13*
1. Network Interface
2. DS3 Timing
3. DS3 Remote Loopbacks
4. DS3 XCV Threshold
1. M12 (4xT1)*
5-11. DS2 Mode (DS2 #1-7)
2. G.747 (3xE1)
12. DS3 Equipment Identification
2. T1/E1 Interfaces
1. IS
1. Card 1A
2. OOS
2. Card 1B
3. Service States
T1/E1 #1-28
3. Facility Service States
29. DS3
30. Set Multiple
1. Perform Manual Switch
2. Minimum Switching Period (sec.) (10*)
4. Protection
3. Maximum Switch Threshold (3*)
5. Save Provisioning
6. Restore Factory Defaults
7. Card Reset
1. Disabled
8. Auto Save
2. Enabled*
9 . Loopback Timeout
10 . Card Pair ID
1. Near End Daily
2. Near End Quarter Hourly
3. Far End Daily
4. Far End Quarter Hourly
5. Near End Daily Thresholds
6. Near End Quarter Hourly Thresholds
7. Near End Daily Thresholds
8. Near End Quarter Hourly Thresholds
1. Near End Daily
2. Near End Quarter Hourly
3. Near End Daily Thresholds
4. Near End Quarter Hourly Thresholds
Warranty information can be found at www.adtran.com/warranty.
1. Loop
1. Disabled
2. Local*
1. Disabled*
2. FEAC/C-BIT*
2. 1E-3
3. FEAC
3. 1E-4
4. C-BIT
4. 1E-5
5. 1E-6
1. T1/E1 State
(T1/E1 #1-28)
2. T1/E1 Line Coding
(T1/E1 #1-28)
(T1/E1 #1-28)
3. T1/E1 Line Length
(T1/E1 #1-28)
4. T1/E1 Loopback Detection
30. Protection Threshold (1-28): 1*
5. T1/E1 Circuit Protection
(T1/E1 #1-28)
(T1/E1 #1-28)
6. T1/E1 Line Identification
(T1/E1 #1-28)
7. T1/E1 XCV Threshold
1. Disabled
2. 1 Minute
3. 5 Minutes*
4. 10 Minutes
5. 15 Minutes
6. 30 Minutes
7. 45 Minutes
8. 60 Minutes
T1/E1 Loopbacks (T1/E1 #1-28)
1. Data Mode
2. Line Loopback
29. DS3 Loopbacks
3. Digital Loopback
4. Remote Loopback
5. Remote ALL T1/E1
1. Data Mode
30-36. DS2 #1-7 Loopbacks
2. Network Loopback
37. Reset ALL Tests
1. QRSS
38. Pattern
2. ALL ONES
3. ALL ZEROES
4. 2 in 8 (2:6)
5. 1 in 8 (1:7)
6. 2 ^15-1 INV
PRICING AND AVAILABILITY 800.827.0807
TECH SUPPORT 800.726.8663
RETURN FOR REPAIR 256.963.8722
1. 2 seconds*
2. 1 hour
3. 2 hours
4. 12 hours
29. Set Multiple
5. 1 day
1. Disabled
6. 2 days
30. Auto Enable Delay
7. 7 days
2. Enabled
3. Auto Enable*
1. AMI
T1:
2. B8ZS/HBD3*
1. 0-133 ft*
2. 133-266 ft
1. Disabled*
3. 266-399 ft
2. CSU (T1 Only)
4. 399-533 ft
3. NIU (T1 Only)
1. Disabled
5. 533-655 ft
2. Enabled*
E1:
1. Disabled*
1. 0-6dB Loss
2. 1E-3
3. 1E-4
T1:
4. 1E-5
1. Data Mode
5. 1E-6
2. Tributary
3. Analog Network
4. Digital Line/Net
5. CODEC Line/Net
6. Remote Loopback
7. CSU Loopback
8. CSU LB w/BERT
9. NIU Loopback
10. NIU LB w/BERT
11. Line BERT
E1:
1. Data Mode
2. Tributary
3. Analog Network
4. Digital Line/Net
5. CODEC Line/Net
6. Remote Loopback
7. Line BERT
www.adtran.com
61186002L5-22A
Advertisement
