Page 1
Instructions/Parts Electric Electric Electric Back Back - - - Gear Back Gear Gear Drum Drum Agitators Drum Agitators Agitators 3A4548G Heavy duty, duty, back back- - - geared geared agitator agitator for for mixing mixing and and maintaining maintaining suspension suspension of of of industrial industrial coatings coatings stored...
Servicing the Gear Reducer......13 Warnings ............5 Additional Agitator Service......14 Installation............7 Parts..............15 Models 25C483 and 25C484 ......15 Back-Gear Mounting Hole Dimensions ... 7 Models 25C485, 25C486, 25C487, Assembling and Positioning the 25C488.......... 17 Agitator .......... 7 Models 25C374, 25C451, 25C480, With or Without an Elevator ......
25C484 ATEX Listed Table 2 2 2 Models Models with with UL UL Listed Listed Explosion Explosion Proof Proof Inverter Inverter Duty Duty Motor Motor (with (with 25C483) 25C483) Table Table Models with Listed Explosion Proof Inverter Duty Motor (with...
Page 4
Models Table 3 3 3 Models Models with with ATEX ATEX Listed Listed Explosion Explosion Proof Proof Inverter Inverter Duty Duty Motor Motor (with (with 25C484) 25C484) Table Table Models with ATEX Listed Explosion Proof Inverter Duty Motor (with 25C484) Elevator Shaft Shaft...
Warnings Warnings Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.
Page 6
Warnings WARNING WARNING WARNING EQUIPMENT EQUIPMENT EQUIPMENT MISUSE MISUSE HAZARD MISUSE HAZARD HAZARD Misuse can cause death or serious injury. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated Technical Data Data in all equipment manuals.
Assembling and and Positioning Positioning the Assembling Assembling Positioning the drum cover on the barrels with the Graco logo Agitator centered and facing you, as shown in Fig. 1. Proceed Agitator Agitator to step 1 in With or Without an Elevator, page 8...
Page 8
Installation With or or or Without Without an an Elevator Elevator With With Without Elevator 1. Install the agitator shaft (33) by threading it into the stub (6) on the bottom of the back-gear housing (1). See Figure 2. 2. Slide the agitator shaft through the large hole in the center of the drum cover (not shown).
Figure 3 Siphon Tube See the VFD manufacturer’s manual for information on installation and operation of the VFD. For a Graco supplied VFD, see manual 3A4793 for information on VFD installation and operation. Connect VFD VFD to to to Motor...
Page 10
P2 into the control portion of a manual reset start circuit. The equipment must be grounded to reduce the For Graco supplied VFDs, motor thermostat leads P1 risk of static sparking and electric shock. Electric and P2 connect to terminals 4 and 13B on the VFD, or static sparking can cause fumes to ignite or as shown below.
Pre - - - Start Start Checklist Start Checklist Checklist operating information. For a Graco supplied VFD, see manual 3A4793 for operating information. Verify each of the following items before starting the Agitators are used to maintain solids in suspension. pump.
Service Service Service Service 6. Clean the inside and outside of the siphon tube, flush the inside of the agitator shaft (33), and clean the agitator blades (34) and the outside of the shaft. 7. Reassemble the siphon tube by doing the reverse of steps 2 through 4.
NOTICE NOTICE NOTICE replacement kit or gear replacement, it is advisable to send the unit to a Graco distributor for repair or To prevent damage to the bearings and seals, replacement. avoid scraping them against the threaded agitator shaft while lowering the lower housing in place.
Parts Parts Parts Parts Models Models Models 25C483 25C483 25C483 and and 25C484 25C484 25C484 Back-Gear Back-Gear Drive Back-Gear Drive Drive 3A4548G...
Page 16
25C968 XP 50 HZ (model 117536 SOCKET HEAD; 25C484) M8 x 1.25 x 25 mm STUB, SHAFT, PLATE, ADAPTER 16A519 17N540 AGITATOR (model 25C483) 113363 SEAL, BEARING PLATE, ADAPTER 17P439 (model 25C484) 190980 BEARING, NEEDLE GEAR, PINION; 190989 GEAR 17N541 0.625 ID (model...
Parts Models 25C485, 25C485, 25C486, 25C486, 25C487, 25C487, 25C488 25C488 Models Models 25C485, 25C486, 25C487, 25C488 Agitator Agitator with Agitator with or or or without with without without Siphon Siphon Siphon 3A4548G...
Parts Part Part No. Part Description Description Description Part Part Part No. Description Description Description 194390 HOUSING, BOTTOM SCREW, CAP, 117536 SOCKET HEAD; 194389 HOUSING, TOP M8 x 1.25 x 25 mm 191004 BEARING, NEEDLE KIT, SHAFT, 24D311 AGITATOR (includes 100069 BALL Ref.
Parts Models 25C374, 25C374, 25C451, 25C451, 25C480, 25C480, 25C481 25C481 Models Models 25C374, 25C451, 25C480, 25C481 Agitator Agitator with Agitator with with Drum Drum Drum Cover Cover and Cover and Elevator Elevator (elevator Elevator (elevator (elevator maximum working working pressure pressure 100 100 psi, psi, 7 7 7 bar)
Dimensions Models 25C485, 25C485, 25C486, 25C486, 25C487, 25C487, 25C488 25C488 Models Models 25C485, 25C486, 25C487, 25C488 UL Listed Listed Agitator Listed Agitator Agitator with with with or or or without without Siphon, without Siphon, Models Siphon, Models 25C485, Models 25C485, 25C486 25C485, 25C486 25C486...
Page 23
Dimensions Atex Listed Listed Agitator Agitator with with or or or without without Siphon, Siphon, Models Models 25C487, 25C487, 25C488 25C488 Atex Atex Listed Agitator with without Siphon, Models 25C487, 25C488 ATEX ATEX Listed ATEX Listed Listed Reference Measurement in (cm) Reference Measurement in (cm) Reference...
Power Usage Charts Power Usage Usage Charts Charts Power Power Usage Charts UL Motor Motor Motor Power Power Power Usage Usage Usage Chart Chart Chart Material Viscosity Viscosity Material Material Viscosity 3000 cp Power Power (W) Power 1000 cp 0 cp Agitator RPM Agitator Agitator...
Technical Specifications Technical Specifications Specifications Technical Technical Specifications Electric Electric Back Electric Back- - - Gear Back Gear Drum Gear Drum Agitators Drum Agitators Agitators UL: 3/4 hp; Motor Power ATEX: 0.37 kW UL: Explosion Proof Class 1 Group C&D Class 2 Group F&G T3C Motor Hazardous Location Approvals ATEX/IECEx: Ex II 2G Ex d IIB T4 Gb (see...
Page 28
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts.