Advertisement
PARTS IDENTIFICATION
1. PHONES jack
2.
STANDBY indicator
3. Remote sensor
4. PLAY / PAUSE
5. VOLUME UP
button
6. SKIP
/ TUNING DOWN
button
7. VOLUME DOWN
1
8. SKIP
/ TUNING UP
button
9. LCD display
10.
STANDBY / ON button
11. STOP
/ BAND button
12. SLEEP / TIMER button
2
9
3
13. MEMORY
button
4
14. FUNCTION (CD / AUX /
10
5
TUNER) button
11
6
12
15. CD door
13
7
14
16. AC cord
8
15
17. Speaker terminal
18. AM (MW) loop terminal
19. AUX IN jack
20. FM antenna wire
Note : 16 to 20 are under the
17
rear cabinet cover.
18
19
20
16
LISTENING TO THE RADIO
TUNING INTO A STATION MANUALLY
1. Press the FUNCTION button to
3. Press the TUNING / SKIP
TUNER.
buttons to select a station.
2. Press the
STOP/BAND button to
select the desired band.
FOR BETTER RECEPTION
F M
AM/MW
Fully unwind the wire antenna. Then
Connect the loop aerial (provided) to
extend the wire antenna and place it
the "AM (MW) ANT." snap terminal.
in the position that sounds best.
Set the
MW/AM loop antenna to a
direction for the better reception.
NOTE: DO NOT CONNECT TO AN
OUTSIDE ANTENNA.
TO SEARCH FOR A STATION
TO RECEIVE THE FM BROADCAST
AUTOMATICALLY
IN STEREO
Press the TUNING / SKIP
/
button
When receiving FM broadcasts in stereo,
for 1 to 2 seconds, and a station is
The word " (
(
STEREO
)
) " illuminate.
searched for automatically. After tuning
in a station, the search stops.
The search may not stop at a station with
a very weak signal.
CONNECTIONS
RIGHT
SPEAKER
BOX
button
3
2
4
5
For external source
button
1. SPEAKER CONNECTION
Remove the rear cover and connect the right speaker to
the R terminals, and the left speaker to the L terminals.
Connect the wires with the red lines (or printed white
lines) to the red (+) terminals and the plain-black wires
to the black (–) terminals.
NOTE : Connecting speakers other than the speakers
supplied with the unit may damage the unit.
2. CONNECTION WITH OTHER OPTIONAL EQUIPMENT
To listen to or record audio signals from external units through this unit.
Connect the signal cord between the unit's AUX jack and the output jack of
the external equipment.
LISTENING TO THE CONNECTED EQUIPMENT
• Press the FUNCTION button to AUX.
3. MW/AM LOOP ANTENNA CONNECTION
Do not connect to an outside antenna. Connect the supplied MW/AM loop
antenna to receive better MW/AM broadcast signal.
4. FM ANTENNA WIRE
Do not connect to an outside antenna.
5. POWER CORD CONNECTION
Before use, check that the rated voltage of your unit matches your local
voltage. Make sure speakers are connected correctly before plugging the AC
power cord into an AC outlet.
Caution: • Be sure the AC power cord is disconnected and all functions are
off before making connections.
• To prevent electrical shock, match wide blade of plug to wide slot,
fully insert. (For N. America)
PRESETTING STATION (for remote only)
Your favourite Radio Stations can be tuned in to by selecting their preset numbers.
It is possible to store up to 10 preset stations for FM band and 10 preset stations for
/
AM/MW band in the order of your choice.
Manual memory presetting
This feature allows you to manually preset stations to any desired channel.
1. Set to the desired band and
3. Press the PRESET+/ALBUM+ button
to select a channel number for the
station.
preset station on the remote control.
4. Press the MEM
2. Press the MEM
button until the
the station.
MEMORY indicator is shown and
" 01 " will blink on the display.
5. Repeat steps 1 to 4 for the next
preset.
TUNING INTO A PRESET STATION
Press the PRESET+/ALBUM+ or PRESET–/ALBUM– button to select a preset
number.
NOTE:
If a button is not pressed within 10 seconds the preset mode will be cancelled
automatically.
TURNING ON THE UNIT
TO TURN ON THE UNIT
Press the
STANDBY/ON button, the
1
function and the corresponding function indicator will light up.
LEFT
TO TURN OFF THE UNIT
SPEAKER
BOX
Press the
STANDBY/ON button to STANDBY, the
only clock display will light up.
CLOCK SETTING
1. In standby mode, press and hold
To AC outlet
the MEMORY
button for about
3 seconds until time format blinks
on display.
R
L
2. Press the TUNING / SKIP
buttons to set 12 Hour or 24 Hour
time format.
3. Press the MEMORY
• Play the external source.
Hour blinks.
ADJUSTING THE SOUND
TO ADJUST THE VOLUME
Press the VOLUME UP / DOWN button to obtain the
desired volume level.
FOR PRIVATE LISTENING
Connect headphones (Ø3.5 mm stereo mini-plug) to the
PHONES
speakers automatically disconnected.
TO SELECT X-BASS (FOR REMOTE ONLY)
X-BASS is designed specifically to boost the low frequency
sound to obtain a more powerful bass.
CD PLAYBACK
1. Press the FUNCTION button to CD.
2. Open the CD door. Hold the disc by
its sides and carefully make it fit
onto
the
central
compartment with the label side
facing towards you until you hear a
"click". The total number and the total
time of tracks will show on the display.
button to memorize
Locating a particular point in a track
To move backward at high speed
Keep the SKIP
button pressed
during play and release at the desired
point.
To move forward at high speed
Keep the SKIP
button pressed
during play and release at the desired
point.
Keep it pressed
NOTE :
The CD player may skip if the loud speakers are situated close to the player and if
high volume or x-bass levels are used.
TIMER OPERATION
TIMER PLAY AND TURN OFF THE UNIT AUTOMATICALLY
The power can be turn on or turn off automatically at a preset time. So that you can
indicator will turn off. Select the desired
listen CD and RADIO function only.
Make sure the clock is correct before TIMER OPERATION. Make sure the time which
use to turn on or turn off is correct, please refer to CLOCK setting procedure.
indicator will light up and
1. Press and hold SLEEP/TIMER button
2. Press the TUNING / SKIP
4. Press the TUNING / SKIP
/
buttons to set correct hour.
3. Press the SLEEP/TIMER
4. Press the
5. Press the MEMORY
button, the
/
Minute blinks.
5. Press the TUNING / SKIP
6. Press the SLEEP/TIMER button, the
6. Press the TUNING / SKIP
/
buttons to set correct minute, and then
NOTE : 1. To check the TIMER, press the TIMER button twice (for remote only).
press the MEMORY
button to start
the clock.
button, the
SLEEP SETTING
When the sleep timer is used, the power is automatically turned off after the specified
time passes.
1. Press the SLEEP/TIMER button while
jack. When headphones are connected,
NOTE :
Press SLEEP/TIMER button to set the sleep timer after 5 seconds. The sleep setting
is automatically turned on.
PROGRAMMING TRACKS - in the CD stop mode (Up to a maximum of
64 tracks)
3. To start playing, press the PLAY/
PAUSE
button.
1. Press the MEM
TO INTERRUPT PLAYBACK
support
of
Press the PLAY/PAUSE
button.
The track time will blink.
To resume playback, press the PLAY/
PAUSE
button again.
2. Press the SKIP
TO STOP PLAYBACK
Press the STOP
button.
Searching for the beginning of a track
To find a previous track
Press the SKIP
button once to
return to the beginning of the current
track.
Press the SKIP
button repeatedly
To check the program
to skip tracks backward one by one.
While in the stop mode, press the MEM
To skip tracks
button. The disc, track and program
Press the SKIP
button repeatedly
numbers will appear on the display.
to skip track(s) forward one by one.
Press the MEM
the other programmed selections.
These displays do not appear during pro-
grammed play.
Press it once
7. Press the TUNING / SKIP
for about 3 seconds until the "
" and
buttons to set minutes.
"on" indicators will on the display
8. Press the SLEEP/TIMER button, the
and the hour will blinks on the display.
"TUNER" will blink on the display.
/
9. Press the TUNING / SKIP
buttons to set hour.
buttons to set CD or TUNER.
button, the
10.Press the SLEEP/TIMER button, the
minute will blink.
"VOL" will blink on the display.
TUNING / SKIP
/
11.Press the TUNING / SKIP
buttons to set minutes. Press the
buttons to set volume.
SLEEP/TIMER
button,
the
"off"
12.Press the SLEEP/TIMER button to
indicator will on the display and the
"confirm" and turn on time, turn off
hour will blink on the display.
time, CD or TUNER, VOL will
/
sequence automatically on display.
buttons to set hour.
Finally the "
" indicator and clock
time will on the display.
minute will blink.
2. To cancel the TIMER function, press the TIMER button once (for remote
only) and "
" will go out in the display.
2. Press the SLEEP/TIMER button one by
the power is on. "SLEEP 90" lights in
one to select the length of remaining
the display.
time until the unit turns off.
Note: SLEEP can be adjusted in
It changes the indicator in the
TUNER, CD and AUX modes.
following way:
The sleep timer is set and the word
"SLEEP" is shown on
the display.
To cancel the sleep timer, press the
SLEEP/TIMER button until "SLEEP" go
out in the display.
button.
3. Press the MEM
button again.
/
buttons to
4. Repeat alone step 2 and 3 procedure
select the desired tracks.
to program additional tracks. Press
PLAY/PAUSE
button to start
playback of the programmed tracks
and memory indicator will appear
on display.
To play the programmed tracks
Press the PLAY/PAUSE
button.
To stop programmed play
button again to view
Press the STOP
button, if you want
to recover programmed play. You can
first press MEM
button and then
press PLAY
button again.
To clear the memory content
Press the STOP
button and then open
the CD door or press MEM
and then press the STOP
button in
stop mode.
/
/
/
button
Advertisement
