Table of contents IR Codes Location and Function of Controls Parts and Button External control device Setup Basic functions RS-232C Setup First Use Wizard Phone jack Type Type of Connector : D-Sub 9-Pin Male Language & Location RS-232C Configurations Communication Parameters Installation Menu IR OUT Using Guide Introduction...
Location and Function of Controls Parts and Button Basic functions Power On (Press) Power Off (Press and Hold) Menu Control (Press Menu Selection (Press and Hold All running apps will close. You can access and adjust the menu by pressing the button when TV is on. You can use the function when you access menu control.
First Use Wizard * Image shown may differ from your TV. Language & Location (Depending on model) • Select the Language and Country. Some countries need to select the Time Zone.
The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’ . The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient operation for Hotelier and System Integrators.
PUBLIC DISPLAY SETTINGS Use the button to select the PUBLIC DISPLAY SETTINGS. Use the ‘OK’ button and then button to select Public Display Mode. - When ‘Public Display Mode’ is set to On (Work), all functions of Public Display Mode apply. Public Display Settings Operation - Decide to work all functions of ‘Public Display Mode’...
IR Operation • Decide whether work the LG remote control or not. - When ‘IR Operation’ is set to ‘Normal’ , all remote keys are available. - ‘Use PWR Only’ makes block all remote keys except power key.
Limited Mode - Configure TV function’s limitation. When selected to ‘On’ , following sub-menus will be worked by below. Setup Menu - Permit to tune and manage Channels as ‘On’(permitted) or ‘Off’(not permitted). Channel Change • Decide to change channel or not by setting ‘Program Change’ as ‘On’(Change Possible) or ‘Off’(Change Impossible) when present source is TV. - When ‘Channel Change’...
DTV Channel Update - It is a mode to set whether to update dtv Channel automatically or not. - When DTV Channel Update is set to ‘Auto’ , the function to update TV’s Channel map according to dtv Channel’s stream information. - DTV Channel Update is set to ‘Manual’...
Network MAC Address • Displays the MAC address (not customizable). Network Setting One-click network connection • Connects easily to a wired network. • This menu supports to connect to an available network. To connect to a network through Set Expert •...
General Configuration Setup Select RCU • It is a mode to set whether to use Select RCU or not. When ‘Select RCU’ is set to ‘Enable’ , You can adjust ‘Number of RCU’ menu. Number of RCU • It is a mode to set Number of RCU. •...
Page 12
15Min Auto Off (Depending on model) • When ‘15Min Auto Off’ is set to ‘Enable’ , TV will turn off if there is no signal in 15Min. Auto Sensing • If ‘Auto Sensing’ is set to ‘On’ , the input is automatically switched when the input signal that you set to “ON’ is received. •...
External Speaker (Depending on model) Volume Control • Selects the volume control method of an external speaker. • You can select ‘Off’ , ‘Int Variable’ Fixed. • Int variable is linked to the main volume OSD and change the volume 0 - 1 Watts. •...
• You will have 2 modes to choose [Default], [HCEC]. • If [Default] is selected, you can use SIMPLINK which is provided in LG TV. Also you can enable and disable SIMPLINK through SIMPLINK MENU. • If [HCEC] is selected, you can use TVLink-HCEC Protocol. (For more detailed information, please refer to TVLink-HCEC Protocol document) IR Decoding •...
Clock Setup (Depending on model) Clock Source • You can select ‘Off’ , ‘TV’ , ‘NTP’ , ‘Admin’ . • NTP : Clock is synchronized using Network Time Protocol. It's only enabled when network cable is connected. • Admin : It's automatically set to Admin when clock is updated by commercial protocols like TVLink-HCEC, TVLink-Interactive, or HCAP API. •...
Welcome Video (Depending on model) Welcome Video Mode • You can set to Off, Once or Repeat. Video Download • You can download video file from USB. • Video file locate LG_DTV folder. Reset • Delete Downloaded video file. Operation •...
TV Manager * Image shown may differ from your TV. You can update files from USB to TV through the TV manager.
Page 18
Ez Download * Image shown may differ from your TV. • Ez Download is a function that enables users to download the desired items all at once, such as EPK (software update file), TLL, Image, Micom. - Images and Software Update files should be copied into the folder named LG_DTV on the USB. »...
Page 19
Export Clone File • “Import Clone File” needs *.TLL file which is generated by “Export Clone File” process. While writing is in process, the user must not turn TV off nor unplug the USB memory card. The following reference images might be slightly different. Import Clone File •...
Page 20
Image Download * Image shown may differ from your TV. • If there are more than two USB Memory Device, It is possible to select the USB. • The download sequence is Image Download Select Image(s) Download. • The target files should be located in “LG_DTV” folder. - Boot Logo Image »...
Page 21
Software Update ► Update TV Software • This feature updates TV software through the EPK file in USB. • The target files should be located in “LG_DTV” folder. • The download sequence is Software Update Update TV Software Select file(EPK) UPDATE.
► Update Micom Software • This feature updates Micom software through the txt file in USB. • The target files should be located in “LG_DTV” folder. • The download sequence is Software Update Update Micom Software Select file(txt) UPDATE. USB Download Menu USB Cloning •...
No Connection (12 V available in some models) (TV) (PC) RS-232C IN • LG TV supports PL2303 chip-based (Vendor ID : 0 x 0557, Product ID (CONTROL & SERVICE) (PC) (TV) : 0 x 2008) USB to serial converter which is not made nor provided by LG.
• Baud rate: 9,600 bps (UART) automatically by IR receiver. • Data length: 8 bits • In this case, LG does not guarantee IR working function. • Parity : None • To make sure of this matter, here are two methods as •...
Command Reference List Transmission / Receiving Protocol (Depending on model) (Depending on Model) DATA Transmission COMMAND1 COMMAND2 (Hexadecimal) 01. Power 00 to 01 [Command1][Command2][ ][Set ID][ ][Data][Cr] 02. Aspect Ratio (page 27) [Command1] : First command to control the TV. (j, k, m or x) 03.
Page 27
1 Power (Command: k a) 4 Volume Mute (Command: k e) ►To control power on or off of the set. ►To control volume mute on/off. You can also adjust mute using the mute button on remote control. Transmission Transmission [k][a][ ][Set ID][ ][Data][Cr] [k][e][ ][Set ID][ ][Data][Cr] Data 00 : Off Data 01 : On...
Page 28
9 Tint (Command: k j) 13 Treble (Command: k r) (Depending upon model) ►To adjust the screen tint. You can also adjust colour in the picture ►To adjust treble. You can also adjust Treble in the audio settings. settings. Transmission Transmission [k][j][ ][Set ID][ ][Data][Cr] [k][r][ ][Set ID][ ][Data][Cr]...
Page 29
17 Equalizer (Command : j v) 19 Tune Command (Command: m a) * This command may work differently Depending upon model and sig- ►Adjust EQ of the set. nal. Transmission * For Europe, Mid-East, Colombia, Asia except South Korea and Japan [j][v][ ][Set ID][ ][Data][Cr] Model ►Select channel to following physical number.
Page 30
• Tune Command Examples: • Analog Antenna/Cable 01. Tune to the Analog antenna (PAL) Channel 10. Data 00 : Physical Channel Number Set ID = All = 00 - Antenna (ATV) : 02~45 (Decimal: 2 ~ 69) Data 00 & 01 = Channel Data is 10 = 00 0a - Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125) Data 02 = Analog Antenna TV = 00 [Data 01 ~ 04]: Major/Minor Channel Number...
Page 31
• Tune Command Examples: • Digital Antenna/Satellite 01. Tune to the Analog cable (NTSC) channel 35. Data 00 : xx (Don’t care) [Data 01][Data 02] : Major Channel Number Set ID = All = 00 Data 01 : High byte Channel Data Data 00 = Channel Data is 35 = 23 Data 02 : Low byte Channel Data Data 01 &...
Page 32
23 Input select (Command: x b) (Main Picture Input) 20 Channel Skip/Add (Command: m b) ►To select input source for main picture. ►To skip current channel for next time. Transmission Transmission [x][b][ ][Set ID][ ][Data][Cr] [m][b][ ][Set ID][ ][Data][Cr] Data 00 : DTV Data 00 : Del(ATSC,ISDB)/Skip(DVB) Data 01 : CADTV Data 01 : Add...