Additional Keypad Operations - Jacuzzi booster KIT spa-pack Installation, Use And Maintenance Manual

(system settings); where this is not the case, subsequently press
the "enter" key.
- Using the key, select the "impostazioni misure" (measure-
ment setting) menu and press "enter".
- Using the key, select "selezione pH" (pH selection) and
press "enter".
- Check that "uscite relè" (relay outlet) has been selected and
press "enter": The display will present "set point1"; press "enter
"once again.
- Ensure that "on" has been selected and press "enter".
Using keys / , set the value 7.00 pH.
- Press "enter" and select the "off" parameter; press "enter" once
again.
- Using keys / , set the value 7.40 pH and press "enter" to
confirm the value selected.
- To exit from the menu and return to normal operation, press
"esc" until "exit" appears on the display and then press "enter".
At this stage, "save?": will appear on the display.
» press "enter" once again to save the changes made;
» press "esc" to exit the menu without saving the changes made.

Additional keypad operations

Activating/changing the password
WARNING: once the password has been set, it will be required
every time access to setting phases is needed.
- Press "esc" : the display should present "impostazioni sistema"
(system settings); where this is not the case, subsequently press
the "enter" key.
- Press "enter" to access the "setup sistema" (system setup)
menu; using the key, select "password".
- Press "enter" once again: the display will present "password: 0".
Press "enter" again until the display presents the two available
options: "stato password" (password status) and "nuova pas-
sword" (new password).
- To activate/deactivate the password, ensure that "stato pas-
sword" (password status) has been selected, press "enter" and,
using the keys, / , select "on" or "off" respectively (when the
password is active, the symbol
- To change the password, select "nuova password" (new pass-
word) and press "enter": Using keys
ue to be assigned to the first figure and press "enter" once again.
Repeat this same operation for the remaining figures.
- Press "enter" for the final time, the display presents "nuova pas-
sword" (new password): at this stage, the password has been set.
appears on the display).
/ , select the desired val-
- To exit from the menu and return to normal operation, press
"esc" until "exit" appears on the display and then press "enter".
At this stage, "save?": will appear on the display.
» press "enter" once again to save the changes made;
» press "esc" to exit the menu without saving the changes
made.
Adjusting the display brightness level
- Press "esc" : the display should present "impostazioni sistema"
(system settings); where this is not the case, subsequently press
the "enter" key.
- Press "enter" to access the setup sistema" (system setup) menu;
using the key, select "display".
- Press "enter" once again: the display presents the two available
options: "contrasto" (contrast) and "retroilluminazione" (back-
lighting).
- To adjust the brightness level, ensure that "contrasto" (contrast)
has been selected; press "enter" and, using keys
desired value.
Press "enter" once again.
- To adjust the time frame during which time the display remains
lit, select "retroilluminazione" (backlighting)
» By selecting "si"(yes), the display remains permanently lit.
» By selecting "no" (no) the display automatically switches itself
off after a minute passes since a key was pressed.
- To exit from the menu and return to normal operation, press
"esc" until "exit" appears on the display and then press "enter".
At this stage, "save?": will appear on the display.
» press "enter" once again to save the changes made;
» press "esc" to exit the menu without saving the changes
made.
Displaying the temperature/redox potential (rdx)
- Alternatively, to view the temperature and redox potential (rdx)
value, repeatedly press "enter" ; the values will be displayed on
the bottom right.
Displaying, set up and back-up of the values
- Press "esc" : the display should present "impostazioni sistema"
(system settings); where this is not the case, subsequently press
the "enter" key.
- Access the "archivio" (archive) and/or "grafici misure" (meas-
urement graphics) to view the chronology and diagrams relative
to the measurements made.
- In particular, by selecting "first value", the display starts from
the first value and continues with the following ones.
By instead selecting "last value", the display starts from the
last value and continues in reverse.
Finally, the "date/time" parameter is used to set the display,
selecting a certain day and time.
40
/ , select the