Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nedap WIM
Summary of Contents for Nedap WIM
- Page 1 installation guide 2017-01-17 | v4.4 | 5279348...
-
Page 2: Table Of Contents
WIM | INSTALLATION GUIDE Content CONTENT 1 INTRODUCTION _______________________________________________________ 3 KEY FEATURES __________________________________________________ 3 2 INSTALLATION ________________________________________________________ 4 SAFETY PRECAUTIONS ___________________________________________ 4 DIMENSIONS ___________________________________________________ 4 3 CONNECTIONS ________________________________________________________ 5 4 ANPR CONFIGURATION _________________________________________________ 7 PLATE READER SETTINGS _________________________________________ 7 4.1.1 EVENTS / ACTIONS ________________________________________ 7 SYSTEM SETTINGS _______________________________________________ 7 4.2.1 SERIAL PORTS ____________________________________________ 7... -
Page 3: Introduction
INTRODUCTION The Wiegand Interface Module (WIM) is developed to be used in combination with the License Plate Reader. The WIM will convert the license plate string into a Wiegand output message. The Wiegand interface is supported by many access control systems. -
Page 4: Installation
• The WIM shall only be installed and serviced by qualified and trained • personnel. The WIM can be powered from a low power, Class 2 power supply, in • compliance with local regulations. • To be sure of safety, do not modify or add anything other than mentioned in this manual or indicated by NEDAP N.V. -
Page 5: Connections
WIM | INSTALLATION GUIDE Connections CONNECTIONS Below the connections are shown which are available on front panel of the device. Shielded cable shall be used for all connections except power supply. RS485 WIEGAND connection output indications connection Figure 2: Front view RS485 Connect the RS485 to the License Plate Reader (9600, 8N1). - Page 6 WIM | INSTALLATION GUIDE Connections The power supply and the DIP-switches are located on the rear panel. See the picture below. Switches Power input Figure 3: Rear view Power input Use the supplied 24VDC power adapter. Power supplies must be able to supply 12 – 24 VDC / 5 Watt (positive voltage at center pin).
-
Page 7: Anpr Configuration
ANPR Configuration ANPR CONFIGURATION This chapter describes the required plate reader settings when using the WIM. These settings must be configured in the plate reader using a web browser and the plate reader's TCPIP interface. See for more details about the plate reader the ANPR installation guide. -
Page 8: Plate Conversion Modes
WIM | INSTALLATION GUIDE Plate Conversion Modes PLATE CONVERSION MODES Note In Wiegand 64-bit mode it The plate conversion mode is selected using the 4 switches located on the device is not required to use the rear panel. LAN connection. - Page 9 WIM | INSTALLATION GUIDE Plate Conversion Modes output message. The first four bits are always 0110. Next 10 groups of 6 bits. Each 6-bit group contains a license plate character. See character conversion table below. If the license plate string contains less than 10 characters, the first groups are «...
-
Page 10: Wiegand Match-List Mode
WIM | INSTALLATION GUIDE Plate Conversion Modes WIEGAND MATCH-LIST MODE In the Wiegand match-list mode, every received license plate message is searched in the match-list. If the plate string is found, then the corresponding Wiegand output message will be transmitted. If the plate string is not found, then no Wiegand output is generated. -
Page 11: Magstripe Iso7811 Track 1
WIM | INSTALLATION GUIDE Plate Conversion Modes selected device. Note Do not transmit the match-list more than 50 times per day, to avoid memory The match-list XL mode is endurance stress. introduced in firmware Do not transmit the match-list XL more than 500 times per day, to avoid memory version 1.10. -
Page 12: Magstripe Iso7811 Track 2
WIM | INSTALLATION GUIDE Plate Conversion Modes Note ISO7811 track 1 details: The magstripe iso7811 Card loaded, Clock and Data signals are active-low. track 1 mode does not Timing per character is 1575 µsec, per bit 225 µsec (= ±4450 Hz). -
Page 13: Barcode Wand Emulation Code39
WIM | INSTALLATION GUIDE Plate Conversion Modes CHAR TK2 CHARS CHAR TK2 CHARS CHAR TK2 CHARS CHAR TK2 CHARS Space " & < > Table 3: ISO7811 track 2 character conversion table Example License plate 'HK55EVB' = B50532525456642F0 License plate 'VR46IT' = B666224265164F4... - Page 14 WIM | INSTALLATION GUIDE Plate Conversion Modes Example License plate HK55EVB: * H K 5 5 E V B * Barcode code39 details: The code39 format contains for each characters 5 bars (black stripes) and 4 spaces (white). Three elements are wide and six elements are small. The ratio between wide and small is 3:1.
-
Page 15: Programmer's Guide
By default DHCP is enabled on the WIM. This means that the WIM will ask upon powerup the DHCP server on the network for an ip-address. You can use the WIM_List software or the Lantronix Device Installer software to assign a fixed ip- address. - Page 16 WIM | INSTALLATION GUIDE Programmer's Guide list. Range from hex 0000 to FFFF. ssss Match-list size. Range from hex 0000 to FFFF. Example 1: QLS006403F0 Match-list size is 1008 entries. Used 100 entries (908 free). Example 2: QLS03E85000 Match-list-XL size is 20480 entries.
- Page 17 WIM | INSTALLATION GUIDE Programmer's Guide 1 to 10 characters. ww..ww Wiegand output specification. Is exactly 12 hex characters and includes a start- bit and the complete Wiegand output format. E.g. parity bits, facility code, id- number. Example 1: Request the 1 match-list entry.
-
Page 18: Atechinal Specifications
WIM | INSTALLATION GUIDE Techinal Specifications TECHINAL SPECIFICATIONS Item Specification Remark Article number 9958789 incl. power adapter Dimensions 130 x 125 x 35 mm [ 5.1 x 4.9 x 1.4 " ] Weight 600 gram Housing Aluminium die-cast zinc alloy... -
Page 19: Bdisclaimer
WIM | INSTALLATION GUIDE Disclaimer DISCLAIMER This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no license under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifica- tions and availability of goods mentioned in it are subject to change without notice;... -
Page 20: Cdocument Revision
WIM | INSTALLATION GUIDE Document revision DOCUMENT REVISION Version Date Comment 2017-01-17 Shielded cable requirement added 2015-04-28 Document number on front page 2015-04-28 Connections front view image improved 2015-03-23 HR update 2014-02-26 Layout adjusted to new corporate style 2013-11-21 Added match list XL...