Page 1
COLOR VIDEO CAMERA SSC-DC132P SSC-DC134 SSC-DC134P SSC-DC138P SERVICE MANUAL 1st Edition...
Page 2
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. SSC-DC132P/134/134P/138P...
Semiconductors that cannot be searched for on this CD-ROM are listed in the service manual for the corresponding unit. The service manual contains a com- plete list of all semiconductors and their ID Nos., and thus should be used together with the CD-ROM. Part number: 9-968-546-XX SSC-DC132P/134/134P/138P...
Record these numbers in the spaces provided below. Afin d’éviter tout risque d’incendie ou d’electrocution, ne Refer to these numbers whenever you call upon your Sony dealer pas exposer cet appareil à la pluie ou à l’humidité. regarding this product.
Page 10
AC 220-240V, 50 Hz power cord and may cause malfunction and/or damage to the video camera. • The SSC-DC132P must always be operated with a DC 12 V power Features supply. • The SSC-DC138P must always be operated with an AC 220 to 240V * (Super Hole- •...
Page 11
4 LOCK screw. 2 Tripod adapter (On SSC-DC134, the tripod adapter is attached on top of the main body. On the SSC-DC132P/SSC-DC134P/ DC138P, it is attached underneath the main body.) The tripod adapter can be attached to either the top or bottom of the camera using the 4 attached screws.
Page 12
When attaching a C-mount type lens, be sure to turn the C/CS adjust- ment ring fully in the “C” direction. When the C/CS adjustment ring is set to “CS,” mounting any lens with a mount projection of more than 4 mm may damage the internal parts of the camera. LOCK SSC-DC132P/134/134P/138P...
Page 13
• To prevent a short circuit, do not let the exposed transformer leads brush against conductive material when connecting to the AC 24V terminals. Connecting the SSC-DC132P Connect the power lines to the camera. Connect the 75-ohm coaxial cable to the video monitor.
Page 14
SSC-DC132P: DC 12 V ±10% SSC-DC134P: AC 24 V, 50Hz SSC-DC138P: AC 220-240V, 50Hz Power consumption SSC-DC134/DC134P: 4.0W SSC-DC132P: 0.2 A (DC 12 V) SSC-DC138P: 4.5 W Sync system SSC-DC134: AC line lock 60Hz SSC-DC132P: Internal SSC-DC134P/DC138P: AC line lock 50Hz...
+ B2 x 4 Cover, Power supply SSC-DC138P only + B2 x 4 + B2 x 4 Case, rear Flat cable Front block ass'y + B2 x 4 + B2 x 4 Case, lower + B2 x 4 + B2 x 4 SSC-DC132P/134/134P/138P...
2-2. Replacement of Power Cord (SSC-DC138P only) When replacing the power cord, use a new cord clamper and secure the clamper onto the cord with a pair of pliers first, and then attach the rear panel. Cord clamper 3 mm Cord Pliers SSC-DC132P/134/134P/138P...
CCD via IC303 driver. Also, a synchronizing signal necessary for the timing (4) 3.3V Generation Circuit (SSC-DC134/134P/138P) generator is got from the SYNC signal generator in the IC311. The IC616, Q602, Q608 periphery circuits generate 3.3 V from 5.0 V. SSC-DC132P/134/134P/138P...
Page 18
3-4. IR-34 Board 3-7. PS-601 Board (SSC-DC132P only) This board incorporates noise filter and automatic iris lens DC12 V(CN901 pin 1) that was input from the external makes 5.0 V, 3.3 V,15.0 V, and _8.5 V through the DC- connector.
. For the confirmation after the adjustment . ND Filter . Vectorscope ND 25 (25 %) 50 by 50 mm square . Waveform Monitor . Make the transmission factor to 6.25 % with double ND . Color Monitor filter . Oscilloscope . Digital Voltmeter SSC-DC132P/134/134P/138P...
4-1-2. Connection for Adjustment 4-1-3. Adjustment Commander Pattern box LCD display of remote control for adjustment (PTB-500/700) Oscilloscope CAMERA Power Supply SSC-DC132P: DC 12V VIDEO Display Data Display Mode SSC-DC134: DCP board AC 24V 60 Hz CN201 Remote control for adjustment...
TP4 : PG in initial data? E1 : GND (Note) Write in initial data (Refer to 4-2-2) (Note) As for SSC-DC132P the VCO adjustment is unnecessary. Has VCO voltage been adjusted on DCP printed circuit board? Adjust VCO voltage _Commander Relay Tool_...
Mode “2E”. Subsequently, press the CHANGE DATA button to display Data “01”. 5. Press the DATA write button of the commander. 6. The numerals indicated on the LCD of the commander will go out for a few seconds and then will reappear. SSC-DC132P/134/134P/138P...
2. Press the CHANGE DATA button so that a deter- mined voltage will fall within a range of standard values. Subject Free Wave Measurement point Relay Tool TP3 (V-SUB) From Equipment Digital voltmeter (DC Voltage) Display Mode (V SUB Set Value) ± 0.25 V Specification SSC-DC132P/134/134P/138P...
Measurement point VIDEO OUT image level Specification The white bright spot is placed over the origin of the vectorscope. Equipment Waveform Monitor Display Mode 95 ± 3 IRE (NTSC) Specification 678 ± 20 mV (PAL) IRIS OUT Image Level SSC-DC132P/134/134P/138P...
Color Bar Chart Measurement point Respective color bright spot of VIDEO OUT Equipment Vectorscope Display Mode 03, 04, 05, 06, 07, 08, 09, 0A Specification The center of the bright spot for each color is in its respective reproduction range. SSC-DC132P/134/134P/138P...
40 ± 4 IRE (NTSC) Specification 286 ± 30 mV (PAL) Lens iris Close 4-5-2. Checking Burst Level Adjustment Check to see if the measured voltage is within the speci- fied range. Subject Free Equipment Vectorscope Specification Burst level is 75% SSC-DC132P/134/134P/138P...
Oscilloscope (AC 200 mV, 10 µs) Equipment 860 ± 40 mV Specification If there is a point where specified value for step 3 is satisfied while varying the iris within the specified value range for step 2, the adjustment is correct. 4-10 SSC-DC132P/134/134P/138P...
5. Remove the C14 filter and perform step 3 and step 4. If there is a point where the specified value for step 4 is satisfied while varying the lens iris within the specified value range for step 3, the adjustment is correct. 4-11 SSC-DC132P/134/134P/138P...
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts list has the present standardized repair parts.
A-8326-821-A o MOUNTED CIRCUIT BOARD, DCP-33N 3-601-824-41 o CASE,REAR(FOR AC24V) (for SSC-DC134) (for SSC-DC134/134P) A-8326-839-A o MOUNTED CIRCUIT BOARD, DCP-33PA 3-601-824-51 o CASE,REAR(FOR DC12V)(for SSC-DC132P) (for SSC-DC134P/138P) 3-601-837-21 o CASE,REAR(FOR AC230V)(for SSC-DC138P) A-8326-846-A o MOUNTED CIRCUIT BOARD, DCP-33PD 3-601-827-11 o CASE,LOWER...
Page 33
PS4 x 6 B2 x 4 SSC-DC138P only B2 x 4 B2 x 4 B2 x 4 B2 x 4 B2 x 4 B2 x 4 B2 x 4 B2 x 4 B2 x 4 B2 x 4 SSC-DC132P/134P/138P only SSC-DC132P/134/134/P/138P...
1-218-231-11 s RESISTOR,CHIP 1 1/2W (4532) R414 1-218-626-11 s RESISTOR,CHIP 100/1W (6331) R415 1-220-332-11 s RESISTOR,CHIP 100K 1/2W (4532) R416 1-220-332-11 s RESISTOR,CHIP 100K 1/2W (4532) R417 1-220-332-11 s RESISTOR,CHIP 100K 1/2W (4532) R420 1-216-043-91 s RESISTOR,CHIP 560 1/10W(2125) SSC-DC132P/134/134P/138P...
Page 35
1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V [for SSC-DC132P] C313 1-162-970-11 s CAPACITOR,CERAMIC 0.01MF/25V B C314 1-162-919-11 s CAPACITOR,CERAMIC 22PF/50V CH FL801 1-239-466-21 s FILTER,EMI [for SSC-DC132P] C315 1-135-259-11 s CAPACITOR,TANTALUM 10MF/6.3V C316 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V R801 1-216-864-11 s RESISTOR,CHIP 0 1/16W (1608)
Page 36
8-759-271-88 s IC TC7SHU04FU [for SSC-DC134] [for SSC-DC134/134P/138P] C361 1-162-920-11 s CAPACITOR,CERAMIC 27PF/50V CH [for SSC-DC134/132P] IC309 8-759-271-88 s IC TC7SHU04FU [for SSC-DC132P] C363 1-162-970-11 s CAPACITOR,CERAMIC 0.01MF/25V B IC311 8-752-379-66 s IC CXD2180AR C364 1-135-259-11 s CAPACITOR,TANTALUM 10MF/6.3V IC312...
Page 37
1-162-970-11 s CAPACITOR,CERAMIC 0.01MF/25V B [for SSC-DC134/134P/138P] C641 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V C642 1-135-177-21 s CAPACITOR,TANTALUM 1MF/25V X301 1-760-321-11 s VIBRATOR, CRYSTAL [for SSC-DC132P] [for SSC-DC134/134P/138P] X302 1-760-314-11 s VIBRATOR, CRYSTAL X303 1-579-994-12 s VIBRATOR, CERAMIC [for SSC-DC134] C644 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V...
Page 38
1-216-864-11 s RESISTOR,CHIP 0 1/16W (1608) [for SSC-DC134] L601 1-412-030-11 s INDUCTOR,CHIP 22UH (3225) R628 1-216-864-11 s RESISTOR,CHIP 0 1/16W (1608) [for SSC-DC134/134P/138P] [for SSC-DC132P/134P/138P] L602 1-412-027-11 s INDUCTOR,CHIP 2.2UH (3225) R629 1-216-829-11 s RESISTOR,CHIP 4.7K 1/16W(1608) [for SSC-DC134/134P/138P] R630...
Page 39
R511 1-216-813-11 s RESISTOR,CHIP 220 1/16W 1608 R512 1-218-698-11 s RESISTOR,CHIP 1.8K 1/16W(1608) R513 1-216-829-11 s RESISTOR,CHIP 4.7K 1/16W(1608) R514 1-216-840-11 s RESISTOR,CHIP 39K 1/16W 1608 R515 1-216-837-11 s RESISTOR,CHIP 22K 1/16W 1608 R517 1-216-821-11 s RESISTOR,CHIP 1.0K 1/16W(1608) SSC-DC132P/134/134P/138P...
In addition, for semiconductors with ID Nos., refer to the separate CD-ROM titled “Semiconductor Pin Assignments” (Sony Part No. 9-968-546-xx) that allows searching for parts by semiconductor type or ID No. The semiconductors in the manual or on the CD-ROM are listed by equivalent types.
Page 49
1-537-768-11 1-537-768-11 NO MOUNT PS-601 F801 1-532-775-51 NO MOUNT NO MOUNT NO MOUNT FL801 1-239-466-21 NO MOUNT NO MOUNT NO MOUNT (SSC-DC132P ONLY) R801 NO MOUNT NO MOUNT R802 NO MOUNT RV801 NO MOUNT 220k 220k 220k CT-216 CT-216 SSC-DC13X_CT-216_001...