Specifications; Standard Equipment; Pre-Operation Inspection - RIDGID RP 350 Manual

Specifications

RP 350 Pistol Press Tool
Attachments.................RIDGID Standard Series
Stroke Length ..............1.57" (40 mm)
Motor
Voltage .....................18 V DC rated
Amperage.................23 A
Power .......................480 Watts
Ram Force...................7,200 lbs. (32 kN)
Head Rotation..............360°
Duty Cycle ...................3 Press
Power Supply ..............RIDGID RB-18XX Series 18 V Li-Ion Battery Pack or RIDGID RPA 120/220 AC Power Adapter
(See Optional Equipment Section)
Bluetooth Range ..........33 ft. (10 m)
Permissible Humidity .....80% maximum
Operating Temperature
Range.............................15° F to 122° F (-10° C to 50° C)
Storage Temperature.....32° F to 113° F (0° C to 45° C)
Weight (no battery/
attachment)....................7.83 lbs (3.55 kg)
Dimensions..................11.3" x 11.0" x 3.1"
287 mm x 279 mm x 77 mm
Sound Pressure (L )*.....<74.5 dB(A), K=3 dB(A)
PA
Vibration* .....................<1.13 m/s
* Sound and Vibration measurements are measured in accordance with a standardized test per Standard EN 62481-1.
- Vibration levels may be used for comparison with other tools and for preliminary assessment of exposure.
- Sound and vibration emissions may vary due to your location and specific use of these tools.
- Daily exposure levels for sound and vibration need to be evaluated for each application and appropriate safety measures taken when needed. Evaluation of exposure
levels should consider the time a tool is switched OFF and not in use. This may significantly reduce the exposure level over the total working period.

Standard Equipment

Refer to the RIDGID catalog for details on equipment
supplied with specific tool catalog numbers.
NOTE! RIDGID press tool attachments are offered in two
"series"
• Standard Series
• Compact Series
These attachment series are not interchangeable. Stan dard
series attachments will only work with standard series
tools (RP 350, RP 351, RP 342-XL, RP 340, RP 330,
320-E, CT-400). Compact series attachments will only
work with compact series tools (RP 240, RP 241, RP 200,
RP 210, 100B).
Selection of appropriate materials and join-
NOTICE
ing methods is the responsibility of the system designer
and/or installer. Before any installation is attempted, care-
ful evaluation of the specific service environment, including
999-995-220.08_REV. B
RP 351 Inline Press Tool
RIDGID Standard Series
1.57" (40 mm)
18 V DC rated
23 A
480 Watts
7,200 lbs. (32 kN)
360°
/min. 3 Press
33 ft. (10 m)
80% maximum
15° F to 122° F (-10° C to 50° C
32° F to 113° F (0° C to 45° C)
7.83 lbs (3.55 kg)
15.7" x 4.65" x 3.1"
398 mm x 118 mm x 77 mm
<74.5 dB(A), K=3 dB(A)
2 , K=1.5 <1.13 m/s
RP 350/RP 351 Press Tools
/min
2 , K=1.5
chemical environment and service temperature, should be
completed. Consult Press Fitting System manufacturer
for selection information.

Pre-Operation Inspection

WARNING
Daily before use, inspect your
press tool and correct any
problems to reduce the risk of
serious injury from electric
shock, crushing injures, attach-
ment failure and other causes, and prevent tool
damage.
1. Switch OFF the tool and remove battery/AC Adapter
from tool.
2. Clean any oil, grease or dirt from the equipment,
especially the handles and controls. This aids inspec-
7