Stanley ProSet XT1 Original Instruction
Hydro-pneumatic power tool
Hide thumbs
Also See for ProSet XT1:
- Instruction manual (172 pages) ,
- Package contents manual (132 pages) ,
- Service manual (24 pages)
Related Manuals for Stanley ProSet XT1
Summary of Contents for Stanley ProSet XT1
- Page 1 Accessories Manual Original Instruction ProSet® XT1 Blind Rivet Tool – 76001 ProSet® XT2 Blind Rivet Tool – 76002 Hydro-Pneumatic Power Tool...
-
Page 2: Table Of Contents
STANLEY Engineered Fastening will not accept any liability for damage resulting from activities carried out by third parties. The working names, trade names, registered trademarks, etc. used by STANLEY Engineered Fastening should not be considered as being free, pursuant to the legislation with respect to the protection of trade marks. -
Page 3: Safety Definitions
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE WARNING: • DO NOT use outside the design intent of Placing STANLEY Engineered Fastening Blind Rivets. • Use only parts, fasteners, and accessories recommended by the manufacturer. •... -
Page 4: Safety Rules
2. SAFETY RULES This technical datasheet must be read with particular attention to the safety warnings and operating instructions listed in the ProSet XT1 and ProSet XT2 Instruction Manual, by any person fi tting or operating the nose assemblies and hand tools. -
Page 5: Straight & Right Angled Swivel Head Nose Assemblies
E N G L I S H 4. STRAIGHT & RIGHT ANGLED SWIVEL HEAD NOSE ASSEMBLIES Swivel Heads are supplied separately for fi tting to a base tool. Jaws and nose tips vary depending on the rivet to be placed, but all other components remain the same within each type of swivel head. Refer to the rivet capability tables 1 below and table 2 on page 3 to select the correct swivel assembly for the rivet to be placed. - Page 6 360 rotation PREPARING THE BASE TOOL TO ACCEPT SWIVEL HEAD EQUIPMENT IMPORTANT - READ THE SAFETY WARNINGS LISTED IN THE PROSET XT1 AND PROSET XT2 INSTRUCTION MANUAL CAREFULLY BEFORE PUTTING INTO SERVICE. IMPORTANT - THE AIR SUPPLY MUST BE TURNED OFF OR DISCONNECTED BEFORE FITTING OR REMOVING THE SWIVEL HEAD NOSE ASSEMBLIES.
- Page 7 E N G L I S H • Remove Return Spring (TP144-082) and Ejector Nozzle (TP143-047), Ejector Body (TP144-146) together with O-Ring (TP144-094), O-Ring (TP144-094). • Rotate Nose Housing (TP144-048) anti-clockwise and remove together with Nosepiece and Nose Housing Nut (TRM00239). •...
- Page 8 E N G L I S H Table 4 - TRM00313 - Swivel Adaptor KIT for XT2 Item Part Number Description 71210-02101 Jaw Spreader Housing 07003-00277 O-Ring TRM00123 Hydraulic Piston Adaptor TRM00030 Adaptor Spacer TRM00496 Swivel Head Connector Assembly TRM00494 Ejector Assembly TRM00033 Collector Adaptor Cover...
- Page 9 E N G L I S H SWIVEL HEAD FITTING INSTRUCTIONS IMPORTANT - READ THE SAFETY WARNINGS LISTED IN THE PROSET XT1 AND PROSET XT2 INSTRUCTION MANUAL CAREFULLY BEFORE PUTTING INTO SERVICE. IMPORTANT - THE AIR SUPPLY MUST BE TURNED OFF OR DISCONNECTED BEFORE FITTING OR REMOVING THE SWIVEL HEAD NOSE ASSEMBLIES.
- Page 10 E N G L I S H Insert Spindle (11) through Adaptor (9) into Jaw Carrier (3) until the hole lines up with slot in Body (5). Temporarily hold in place with Pin (6). Insert Pin (12) through the front slot of Body (5) into Jaw Carrier (3). K.
-
Page 11: Pin Tail Deflector Kit
To replace the stem collector with the stem defl ector proceed as follows: PREPARING THE BASE TOOL TO ACCEPT THE PIN TAIL DEFLECTOR KIT IMPORTANT - READ THE SAFETY WARNINGS LISTED IN THE PROSET XT1 AND PROSET XT2 INSTRUCTION MANUAL CAREFULLY BEFORE PUTTING INTO SERVICE. - Page 12 E N G L I S H Refer to fi g.11 and the table 4 on page 9. Refer also to the ProSet XT1 and ProSet XT2 Service Manuals. • The air supply must be disconnected. • Rotate Collector Bottle Assembly (TRM00227) anti-clockwise and remove from the Collector Adapter (TP153-111).
- Page 13 REMOVING THE PIN TAIL DEFLECTOR KIT. Refer to fi g. 12 and the table 4 on page 9. Refer also to the ProSet XT1 and ProSet XT2 Service Manuals. Item numbers in bold refer to fi g. 12 and table 5, 6.
- Page 14 E N G L I S H Fig. 12...
-
Page 15: Nose Extension Kits
PREPARING THE BASE TOOL TO ACCEPT EXTENSION KIT. IMPORTANT - READ THE SAFETY WARNINGS LISTED IN THE PROSET XT1 AND PROSET XT2 INSTRUCTION MANUAL CAREFULLY BEFORE PUTTING INTO SERVICE. IMPORTANT - THE AIR SUPPLY MUST BE TURNED OFF OR DISCONNECTED BEFORE FITTING OR REMOVING THE SWIVEL HEAD NOSE ASSEMBLIES. - Page 16 E N G L I S H FITTING THE NOSE EXTENSION ASSEMBLY IMPORTANT - READ THE SAFETY WARNINGS LISTED IN THE PROSET XT1 AND PROSET XT2 INSTRUCTION MANUAL CAREFULLY BEFORE PUTTING INTO SERVICE. IMPORTANT - THE AIR SUPPLY MUST BE TURNED OFF OR DISCONNECTED BEFORE FITTING OR REMOVING THE SWIVEL HEAD NOSE ASSEMBLIES.
- Page 17 E N G L I S H Fig. 14 • The air supply must be disconnected. • Install Pulling Head Joint (TRM00013) together with Jaw Guide Lock (TP144-051) and Jaw Guide Lock Spring (TP144-080) to Pulling Head Extension (TRM00012). • Attach Mandrel Guide (TP144-052) to Pulling Head Extension (TRM00012).
-
Page 18: Mcs5000 Adapter Kits
IMPORTANT - THE AIR SUPPLY MUST BE TURNED OFF OR DISCONNECTED BEFORE FITTING OR REMOVING THE MCS5000 ADAPTER KITS. Refer to fi g.18 below. Refer also to the ProSet XT1 and ProSet XT2 Service Manuals. • The air supply must be disconnected. - Page 19 E N G L I S H FITTING THE MCS5000 ADAPTER KITS IMPORTANT - READ THE SAFETY WARNINGS LISTED IN THE PROSET XT1 AND PROSET XT2 INSTRUCTION MANUAL CAREFULLY BEFORE PUTTING INTO SERVICE. IMPORTANT - THE AIR SUPPLY MUST BE TURNED OFF OR DISCONNECTED BEFORE FITTING OR REMOVING THE MCS5000 ADAPTER KITS.
- Page 20 E N G L I S H Item numbers in bold refer to fi g. 19 and table 9. • The air supply must be disconnected. • Install Ejector Assembly (TRM00494) and Return Spring (TP144-082). • Screw End Cap (TP153-112) together with O-Ring (TP154-110), Ejector Guide (TP144-063). •...
- Page 21 Avdel®, Avex®, Avibulb®, Avinox®, Avseal®, Bulbex®, Hemlok®, Interlock®, Klamp-Tite®, Monobolt®, POP®, ProSet®, Stavex® and T-Lok® are registered trademarks of Stanley Black & Decker, Inc. and its affi liates. The names and logos of other companies mentioned herein may be trademarks of their respective owners.