Home Screen - FUTABA T32MZ Manual

Home Screen Display
On the home screen, basic information such as swash type,
gyro operation mode, sensitivity and governor ON / OFF,
engine operating time etc, are displayed.
For functions that can set conditions in
this manual, mark is written.
Cond
Swash plate type
Displays the swash plate type set in
"SWH. BASIC" menu.
Gyro operation mode /
Gyro gain
Displays "AVCS" or "Normal" operation
mode and gyro gain of aileron (roll),
elevator (pitch) and rudder (yaw) axis.
Governor ON / OFF
Indicates the ON / OFF switch status of the
governor function. When "ON" is displayed, the
governor function is activated.
RPM display
The maximum RPM of the engine or rotor head RPM mem-
orized by the governor during operation is displayed. Data
is reset when the power is turned off. If you want to check
multiple times during the flight, leave the power on after
flight. Press and hold RPM button to reset the display.
Home Screen Home Screen
Condition number
With switch operation from the transmitter, several parameters can be switched by
setting up to 5 types of data. If you set the condition switch to the channel having
the AFR function of the transmitter and set the point for each flight condition with the
AFR point curve, it can also be linked with the flight condition switch.
• When either the DG1 or DG 2 switch is selected, the following options are available.
Function Menu of your transmitter (DG1). Assigning DG1 to a switch or flight mode allows the
use of two separate values for the condition selectable parameters.
Switch DG1
Switch Channel Rate
-100% -35%
Cond1
Narrow
• If you set a condition switch channel, using the AFR function on that channel set a flat point
curve for each flight condition. Then you can utilize all 5 flights conditions.
-100% -75%
Cond1 Cond2
100%
0%
-100%
Set the point curve with AFR for each flight condition of the transmitter.
Battery voltage
Displays the voltage of the
receiver battery connected
to CGY.
Roll and Elevator rate maximum display
This screen displays the maximum roll rate and maximum eleva-
tor rate recorded during flight. Data is reset when the power is
turned off. If you want to check the maximum rate, leave the pow-
er on after flight. Press and hold rate button to reset the display.
Engine running time
Displays the running time of the engine. Up to 9,999
hours are displayed.
Press and hold time button to reset the display. The
operation time is stored in memory even when the
power is turned off until it is reset.
6
Ｃond1 (Condition 1)
●BaseGain AI EL
●SWS.Rate ●Cnt.AuthAI ●HeadHld E ●CYC.Rt
●PIT.Rate ●Cnt.AuthEL ●StpTune A ●GOV.Gain
●SWS.Ring ●EXPO ●StpTune E ●L Lmt.H rpm
●FLT.Styl ●HeadHld A ●HeadResp ●L Lmt.L rpm
Ｃond2 (Condition2)
●BaseGain AI EL
●SWS.Rate ●Cnt.AuthAI ●HeadHld E ●CYC.Rt
●GOV.Gain
●PIT.Rate ●Cnt.AuthEL ●StpTune A
●SWS.Ring ●EXPO ●StpTune E ●L Lmt.H rpm
●L Lmt.L rpm
●FLT.Styl ●HeadHld A ●HeadResp
*Indicates when the setup style is "3D".
0% 35% 100%
Cond2
Neutral Wide
Switch Channel Rate
Neutral
-25% 0% 25% 75%
Cond3 Cond4 Cond5
100%