Advertisement
Quick Links
Advertisement
Related Manuals for EAW MKD Series
Summary of Contents for EAW MKD Series
- Page 1 MKD Series U-Bracket Instructions...
- Page 2 Original Instructions These instructions are for defining acceptable MKD800, MKD1000, or MKD1200 U-Bracket installations to a mounting surface and for installing an MKD or MKD-WP Series Loudspeaker to an MKD Series U-Bracket. IMPORTANT SAFETY INSTRUCTIONS – READ THIS FIRST Safety Instructions Read and heed all warnings and safety instructions in this manual before using this product.
- Page 3 1. Inventory Before beginning installation, inventory your available hardware to items listed. Item Description Quantity MKD Series U-Bracket Button Head Screw, M10 X 45mm long Flat Washer Split-lock Washer Rubber Washer, 3mm thick Rubber Washer, 6mm thick **Tools Needed: 6mm Allen wrench**...
- Page 4 3. Installation of the MKD Series U-Bracket to a mounting surface a. Test fit an MKD Series U-Bracket on an MKD Series Loudspeaker to confirm the correct angle, loudspeaker and u-bracket orientation before installing the U-bracket to the mounting surface.
- Page 5 Horizontal configuration d. Level - The back channel of the MKD Series U-Bracket must be level when installed to the mounting surface and before installing an MKD Series Loudspeaker to the U-Bracket. e. Mounting options NOTE: It is recommended that you consult a building professional for the proper mounting hardware before mounting the bracket.
- Page 6 1/2in (M16) conduit adapter. 2. The two inner holes may be used to structurally install the MKD Series U- Bracket to a mounting surface using load bearing hardware; both holes must be secured.
- Page 7 1. If an Angle lock point is not used, the loudspeaker may secure the loudspeaker at any angle by torqueing the mounting point hardware. 2. Note, there is an additional M10 screw in the bottom of each MKD Series loudspeaker. This one location allows for additional angle lock settings when using the MKD Series U-Bracket.
- Page 8 Using a 6mm Allen wrench, remove the flat head screws located at the center of the top and bottom of the MKD Series Loudspeaker. iii. If choosing to use the MKD Series U-Bracket angle lock points, locate the flat head screw in the loudspeaker that corresponds with the intended install angle. Using...
- Page 9 (E or F) and into the loudspeaker’s center threaded mounting hole. Repeat for the opposite side. vi. If using the MKD Series U-bracket’s slotted mounting point “A”, the hardware may be preassembled to the MKD Series Loudspeaker. 1. Note, if using the slotted mounting point, the MKD Series U-Bracket must be installed oriented with the slot angled upward, opposing the ground.
- Page 10 Failure to do so could result in water ingress and damage to the loudspeaker. h. Clean the MKD Series U-Bracket and MKD Series Loudspeaker with a dry cloth. 7. Dismantling the MKD Series U-Bracket installation a.
- Page 11 Carefully lower the u-bracket to the ground. c. Discard all damaged components. EU Declaration of Conformity EAW North America Inc hereby declares that this device is in compliance with Directive 2006/42/EC A copy of this EU Declaration of Conformity is available at https://eaw.com/downloads/#142-660-wpfd- certifications Contacting EAW We have attempted to make this manual and the instructions as thorough as possible.
- Page 12 Eastern Acoustic Works One Main Street Whitinsville, MA 01588 tel 800 992 5013 / +1 508 234 6158 www.eaw.com ©2020 Eastern Acoustic Works All rights reserved. Products are not drawn to scale. All terms, conditions, and specifications subject to change without notice.