Page 3
REV. B SYSTEM QUICK START The MBT 201A and MBT 101A systems are very easy to operate and can be quickly set up for use in standard soldering/desoldering operations. To begin operation of your new system quickly, perform the "Set-Up" and "Quick Start - Basic Operation"...
GENERAL INFORMATION SPECIFICATIONS POWER REQUIREMENTS VACUUM AND AIR PRESSURE ENVIRONMENTAL REQUIREMENTS Ambient Operating Temperature: Storage Temperature: Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
GENERAL INFORMATION PHYSICAL PARAMETERS TEMPERATURE SPECIFICATIONS NOTE True minimum and maximum Operating Tip Temperatures may vary depending on handpiece & tip selection. EOS/ESD Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 10
GENERAL INFORMATION CAPABILITIES Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Likewise, use SensaTemp handpieces on only those systems with an SR-3 or SR-4 rating (marked on front panel of power source). These include other MBT systems (MBT 101A, MBT 201A and higher) and all ST series systems.
GENERAL INFORMATION PARTS IDENTIFICATION Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 13
GENERAL INFORMATION Figure 1. Parts Identification Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 14
HEADING GUIDELINES PACE adheres to the following Heading Guidelines (based on OSHA guidelines) when listing special information or precautions to be taken. Especially important are all procedures and practices which, if not strictly observed, could result in injury or loss of life.
PACE in the associated handpiece manual. 2. The front end (heater end) of the glass solder collection chamber in the PACE Sodr-X-Tractor is hot when the handpiece is in use. When removing the chamber for cleaning, grip the chamber at the rear seal.
Page 16
SET-UP SYSTEM Using Figures 1 thru 4 as a guide, set up the MBT 201A or MBT 101A system using the following steps. 1. Store the shipping container(s) in a convenient location. Reuse of these containers will prevent damage if you store or ship the system.
Page 17
Figure 3. Handpiece Connection 10. To avoid confusion among handpieces on MBT 201A systems, PACE recommends the use of colored markers (P/N 6993-0136 Cable Marker Kit) to identify the particular handpiece power cable and/or air hose. Attach any two like colored markers, one to each end of the handpiece power cable or air hose.
AIR HOSE CONNECTION There are two methods of attaching the Air Hose from the PACE power source to an air handpiece. Select the method which best suits your needs. The Quick Connect Method is best suited for configurations where multiple air handpieces may be in use.
Page 19
3. Prepare a quick connect Air Hose by inserting a metal hose clamp (P/N 1211-0036, standard on MBT 201A systems) & a male quick connect hose mount Fitting (P/N 1259-0087) into each end of a 54 inch (137cm) length of Air Hose. Push the ridged ends of the Fittings into the hose;...
Page 20
SET-UP TRADITIONAL METHOD 1. Connect the 54 inch (137cm) length of Air Hose to the metal tube in the back of each air handpiece. 2. Insert a male quick connect hose mount Fitting (P/N 1259- 0087) to the free end of the 54 inch (137cm) length of Air Hose.
QUICK START - BASIC OPERATION QUICK START PROCEDURE The MBT 201A and 101A systems are very easy to operate. As received from the factory, the system can be quickly set up for use in standard soldering/desoldering operations. Simply perform the following Quick Start Procedure to begin system operation.
Temperature Offset. The PACE “Tip & Temperature Selection System” allows you to select and maintain a True Tip Temperature for any size and type of tip using the appropriate Tip Offset compensation value. The PACE Tip & Temperature Selection System allows you to select and maintain a True Tip Temperature for any size and type of SMT tip.
CORRECTIVE MAINTENANCE VISIFILTER ELEMENT REPLACEMENT Follow the procedure listed below to replace the VisiFilter element when it becomes clogged or discolored. 1. Disconnect the handpiece air hose by gently turning and pulling the coupled Fittings. 2. Disconnect the Visifilter and hose assembly from the Power Source by gently turning and pulling the male Fitting inserted into the AUTO SNAP-VAC Port.
Page 24
CORRECTIVE MAINTENANCE HANDPIECES The following "Heater Assembly Checkout Procedures" are applicable to all PACE SensaTemp handpieces except for the TT-65 ThermoTweez handpiece. Refer to either of the TT-65 manuals (P/N 5050-0300 or 5050-0336) for troubleshooting procedures pertinent to that handpiece.
Manual. Power Source channel. No heat on handpiece. Defective control circuit. Contact PACE Customer Service. Other handpieces do not work on Power Source channel. Table II. Power Source Corrective Maintenance Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Listed below are the replacement parts which may be ordered directly from PACE sales or through your local authorized PACE distributor. Refer to Figure 1, Page 9. To obtain any parts other than those listed below, contact PACE Customer Service directly at Tel. # (301) 490-9860 or Fax # (301) 604-9215.
Page 27
REPLACEMENT PARTS ACCESSORY TRAY, MBT 201A/J/E Listed below are items included in MBT 201A, MBT 201AJ and MBT 201AE System Accessory Trays. PACE PART NUMBER ITEM MBT 201A DESCRIPTION MBT 201AJ MBT 201AE SX-70 Sodr-X-Tractor Handpiece 6010-0077 6010-0077 SP-2A Sodr-Pen Soldering Iron...
Page 28
REPLACEMENT PARTS ACCESSORY TRAY, MBT 101A/J/E Listed below are items included in MBT 101A, MBT 101AJ and MBT 101AE System Accessory Trays. PACE PART NUMBER ITEM MBT 101A MBT 101AE DESCRIPTION MBT 101AJ SX-70 Sodr-X-Tractor Handpiece 6010-0077 6010-0077 Operation & Maintenance Manual...
Page 29
REPLACEMENT PARTS ACCESSORY KIT, MBT 201/J/E Listed below are items included in MBT 201A, MBT 201AJ and MBT 201AE System Accessory Kits. PACE PART NUMBER ITEM NO. DESCRIPTION MBT 201A MBT 201AJ MBT 201AE Tip Tool 1100-0206 1100-0206 1100-0206 Desoldering Tip, 3/16" Shank, .040 I.D.
Page 30
REPLACEMENT PARTS ACCESSORY KIT, MBT 101A/J/E Listed below are items included in MBT 101A, MBT 101AJ and MBT 101AE System Accessory Kits. PACE PART NUMBER ITEM NO. DESCRIPTION MBT 101A MBT 101AJ MBT 101AE Tip Tool 1100-0206 1100-0206 1100-0206 Desoldering Tip, 3/16" Shank, .030 I.D.
Page 31
Instructions Duplicate this form and submit comments on the copy. Keep the original to make future comments. Complete all requested information. Submit completed form to: PACE Incorporated Applications Engineering Fax: (301) 604 - 9215 9893 Brewers Court Laurel MD 20723-1990 U.S.A.