Ranger RP-20FC Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Ranger Manuals
  4. Industrial Equipment
  5. RP-20FC
  6. Installation and operation manual

Ranger RP-20FC Installation And Operation Manual

Oil filter crusher
Hide thumbs
Table of Contents

Advertisement

Quick Links

Installation and Operation Manual
Manual P/N 5900011 — Manual Revision B1 — February 2021
Model:
• RP-20FC
Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.
⚠
DANGER
Oil Filter Crusher
entire
Read the
operation. Failure to follow the instructions and safety precautions
in this manual can result in serious injury or death. Make sure all
other operators also read this manual. Keep the manual near the
product for reference. By proceeding with setup and operation,
you agree that you fully understand the contents of this
manual and assume full responsibility for product use .
contents of this manual prior to setup or
1645 Lemonwood Dr.
Santa Paula, CA 93060 USA
Toll Free 1 (800) 253-2363
Tel: 1 (805) 933-9970
rangerproducts.com

Advertisement

Table of Contents
loading

Related Manuals for Ranger RP-20FC

Summary of Contents for Ranger RP-20FC

  • Page 1 Oil Filter Crusher Installation and Operation Manual Manual P/N 5900011 — Manual Revision B1 — February 2021 Model: • RP-20FC Designed and engineered by BendPak Inc. in Southern California, USA. Made in China. ⚠ entire Read the contents of this manual prior to setup or operation.
  • Page 2 You can always find the latest version of the manual on the BendPak website. Warranty. The BendPak Ranger warranty is more than a commitment to you: it is also a commitment to the value of your new product. For full warranty details and to register your new BendPak Ranger product, contact your nearest BendPak Ranger dealer or visit www.bendpak.com/support/warranty.

  • Page 3: Table Of Contents

    Maintenance Log Introduction This manual describes the RP-20FC, which is an Oil Filter Crusher from BendPak Ranger, which applies up to 10 tons of air-operated pressure to flatten just about any used oil filter to approximately 20 percent of its size while removing up to 95 percent of the leftover oil.

  • Page 4: Shipping Information

    Never attempt to service the unit while it is connected to the air supply. • Secure the unit to a dry, clean, flat concrete surface; do not install it on asphalt or wood. RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...
  • Page 5 BendPak Ranger assumes no liability for damages resulting from: • Use of the equipment for purposes other than those described in this manual. • Modifications to the equipment without prior, written permission from BendPak Ranger. • Injury caused by modifying, disabling, overriding, or removing safety features. •...

  • Page 6: Specifications

    Chamber height 11" / 279 mm Chamber width 8" / 203 mm Chamber depth 11" / 279 mm Average cycle time 15-20 seconds Air Input 125 – 175 PSI RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...

  • Page 7: Components

    Components The following figure shows the major components of the unit. The main components of the RP-20FC are: • Enclosure. Includes the crushing chamber, the Door, the Window, the Press Ram, and the Control Handle. Gets bolted to the top of the Platform.

  • Page 8: Setup

    The fewer times you have to move the components, the fewer opportunities there are for them to get lost, get damaged, or damage the surface they are on. RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...
  • Page 9 6. Attach the Diagonal Leg to the top of the Stand, put the Stand Support in place near the bottom of the Stand, and then secure the bottom end of the Diagonal Leg (1) and Side Supports (2) in place. 7. Move the Stand to the upright position. RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...
  • Page 10 3. Connect the Drain Hose Fitting to the bottom of the Enclosure. 4. Attach the Hose Clamp and Drain Hose to the Enclosure. Mounting Brackets for Power Unit not shown for clarity. RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...
  • Page 11 Make sure to route the Straight Fitting tubing through the opening and behind the Air/Oil Regulator. 4. Securely tighten all the connections. 5. Connect your customer-supplied air pressure to the “Air In”, a minimum of 125 – 175 psi. RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...

  • Page 12: Operation

    The air will exhaust from the press cylinder and the Press Ram will rise. ⚠ Do not open the door while the unit is operating; you must wait for the press to WARNING cycle completely. RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...

  • Page 13: Maintenance

    If you continue to have issues with your Oil Filter Crusher, visit BendPak Support, email us at support@bendpak.com, or call (805) 933-9970. RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...

  • Page 14: Labels

    Labels RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...

  • Page 15: Parts Drawings

    Parts Diagrams RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...
  • Page 16 RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...

  • Page 17: Maintenance Log

    Maintenance Log RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...
  • Page 18 Maintenance Log RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...
  • Page 19 Maintenance Log RP-20FC Oil Filter Crusher P/N 5900011 — Rev. B1 — February 2021...
  • Page 20 1645 Lemonwood Drive Santa Paula, CA 93060 USA © 2021 BendPak Inc. All rights reserved. bendpak.com...

Table of Contents