Advertisement
Quick Links
BEFORE YOU BEGIN
Please read these instructions carefully to
familiarize yourself with the required tools, materials,
and installation sequences. Follow the sections that
pertain to your particular installation. This will help
you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler NZ Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important information
- Please leave these instructions for the consumer.
Please provide adequate available space for the
bath unit in accordance with rough-in. Arrange the
location of drain in advance.
PRODUCT REQUIREMENTS
A. Summary Of Key Requirements
Observe all local plumbing codes.
Install the unit to a level subfloor.
B. Plumbing Specifications
If using a rim-mounted bath faucet, flexible connections between the valves and spout may be required.
Confirm adequate mounting, connection space of specified faucet for your installation.
C. Product Inspection
Uncrate and inspect bath for damage. All Kohler s baths have been manufactured with sophisticated craftsmanship.
However, please inspect for any possible damage that may have occurred in transit. Leave all materials in the carton
during construction to prevent damage.
NOTE: Damage occurred during transit shall not be covered by warranty.
D. New or Replacement Installation Requirements
This bath can be installed in new or existing bathrooms.
For replacement: Remove the old bath, and remove enough old wall material and floor covering from the
area to allow for installation. Remove any old plumbing that does not conform to the rough-in requirements.
For new installation: Position the plumbing according to the rough-in dimensions. Cap the supplies, and check
for leaks.
IMPORTANT:
All installations must comply with council and local
authority by-laws. It is the responsibility of the installer
to ensure that the waste is made watertight by means
of silicone sealant or caulking compound.
NOTE: Bath can be installed after the wall is completed.
Bath drain supplies should be arranged preliminarily
according to the selected bath.
'
1
INSTALLATION INSTRUCTIONS
FREESTANDING BACK-TO-WALL BATH
22160A-0 / 22161A-0
1430641-A02-A
EVOK
22/04/2020
Advertisement
Related Manuals for Kohler EVOK 22160A-0
Summary of Contents for Kohler EVOK 22160A-0
- Page 1 Confirm adequate mounting, connection space of specified faucet for your installation. C. Product Inspection Uncrate and inspect bath for damage. All Kohler s baths have been manufactured with sophisticated craftsmanship. ’ However, please inspect for any possible damage that may have occurred in transit. Leave all materials in the carton during construction to prevent damage.
-
Page 2: Dimensions (Unit:mm)
E. Dimensions (unit:mm) 1498 / 1697 Evok 1500 BTW Bath Evok 1700 BTW Bath 33 Kg 37 Kg Weight 423 mm 423 mm Water depth to overflow 222 L 228 L Capacity 927mm x 465mm 1050mm x 465mm Bathing area 1397mm x 638mm 1583mm x 638mm Top area... -
Page 3: Installation
SITE REQUIREMENTS Subfloor Preparation Check the flooring under the bath, and make repairs as necessary. Make sure the subfloor is level. It is strongly recommended to prepare a waterproof layer for the subfloor beforehand. It may be necessary to plan for a channel in the floor to allow space for a trap, see cross section of the Evok bath and waste below: 42mm BEFORE INSTALLING UNIT... - Page 4 IMPORTANT: The bath must be installed such that it’s level on all top edges. The floor should be flat, level and free of any bumps or protrusions. 2) Carefully shift the bath away from its position and mark out the clip positions with reference to the recommended distances shown below: 740mm for 22160A-0 760mm for 22161A-0...
-
Page 5: Plumbing Installation
DN40 outlet with BSP 1 1/2’’ thread. Connect the waste to an appropriate trap. 2) After plumbing is complete and before lowering the bath check for leaks. Kohler NZ shall not be liable under its warranty for damage caused by negligence. -
Page 6: Important Consumer Information
For spare parts and warranty information, please visit our website: New Zealand Australia www.kohler.co.nz www.kohler.com.au Valence rect - 1112149 NEW ZEALAND AUSTRALIA oval - 1118099 KOHLER NZ LTD KOHLER AUSTRALIA Ph: 0800 564 537 Ph: 1 800 564 537 80mm Leveling Kit Set - 1122542 Fx: 0800 664 488...