Gigabyte R282-Z93 User Manual
  1. Manuals
  2. Brands
  3. Gigabyte Manuals
  4. Server
  5. R282-Z93
  6. User manual

Gigabyte R282-Z93 User Manual

Amd epyc 7003 dp server system - 2u 12-bay gpu sku
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
R282-Z93
AMD EPYC™ 7003 DP Server System - 2U 12-Bay GPU sku
User Manual
Rev. 1.0

Advertisement

Table of Contents
loading

Related Manuals for Gigabyte R282-Z93

Summary of Contents for Gigabyte R282-Z93

  • Page 1 R282-Z93 AMD EPYC™ 7003 DP Server System - 2U 12-Bay GPU sku User Manual Rev. 1.0...
  • Page 2 GIGABYTE's prior written permission. Documentation Classifications In order to assist in the use of this product, GIGABYTE provides the following types of documentation:  User Manual: detailed information & steps about the installation, configuration and use of this product (e.g.
  • Page 3 Conventions The following conventions are used in this user's guide: NOTE! Pieces of additional information related to the current topic. CAUTION! Precautionary measures to avoid possible hardware or software problems. WARNING! Alerts to any damage that might result from doing or not doing specific actions.
  • Page 4 Server Warnings and Cautions Before installing a server, be sure that you understand the following warnings and cautions. WARNING! To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
  • Page 5 Electrostatic Discharge (ESD) CAUTION! ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE, PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT- TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER WHEN HANDLING PARTS.
  • Page 6 Installing or removing jumpers: A jumper is a small plastic encased conductor that slips over two jumper pins. Some jumpers have a small tab on top that can be gripped with fin-gertips or with a pair of fine needle nosed pliers. If the jumpers do not have such a tab, take care when us- ing needle nosed pliers to remove or install a jumper;...

  • Page 7: Table Of Contents

    Table of Contents Chapter 1 Hardware Installation ................... 11 Installation Precautions .................. 11 Product Specifications ..................12 System Block Diagram ................... 15 Chapter 2 System Appearance ..................17 Front View ...................... 17 Rear View ....................... 18 Front Panel LEDs and Buttons ............... 19 Rear System LAN LEDs .................
  • Page 8 The Main Menu ....................53 Advanced Menu ..................... 56 5-2-1 Trusted Computing ....................57 5-2-2 PSP Firmware Versions ..................58 5-2-3 Legacy Video Select ....................59 5-2-4 AST2500 Super IO Configuration ................60 5-2-5 S5 RTC Wake Settings ...................62 5-2-6 Serial Port Console Redirection ................63 5-2-7 CPU Configuration ....................66 5-2-8...
  • Page 9 5-8-2 UEFI Application Boot Priorities ................118 Save & Exit Menu ..................119 5-10 BIOS POST Beep code (AMI standard) ............120 5-10-1 PEI Beep Codes ....................120 5-10-2 DXE Beep Codes ....................120 - 9 -...
  • Page 10 This page intentionally left blank - 10 -...

  • Page 11: Chapter 1 Hardware Installation

    Chapter 1 Hardware Installation Installation Precautions The motherboard/system contain numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the service guide and follow these procedures: • Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer.

  • Page 12: Product Specifications

    Product Specifications NOTE: We reserve the right to make any changes to the product specifications and product-related information without prior notice. Š AMD EPYC™ 7003 series processor family Š Dual processors, 7nm, Socket SP3 Š Up to 64-core, 128 threads per processor Š...
  • Page 13 Expansion Slot Riser Card CRS2014: 1 x PCIe x16 slot (Gen4 x16), FHFL Š Riser Card CRS2026: 2 x PCIe x16 slot (Gen4 x16), FHFL Š Riser Card CRS2026: 2 x PCIe x16 slot (Gen4 x16), FHFL Š 1 x OCP 3.0 mezzanine slot with PCIe Gen4 x16 bandwidth from CPU_0 Supported NCSI function 1 x OCP 2.0 mezzanine slot with PCIe Gen3 x8 bandwidth (Type1, P1, P2) Supported NCSI function...
  • Page 14 Front Panel I/O Š 2 x USB 3.0 Š 1 x Power button with LED Š 1 x ID button with LED Š 1 x Reset button Š 1 x NMI button Š 1 x System status LED Š 1 x HDD activity LED Š...
  • Page 15 Power Supply Š 2 x 2000W redundant PSU Š 80 PLUS Platinum Š AC Input: - 100-120V~/ 12A, 50-60Hz - 180-240V~/ 10A, 50-60Hz Š DC Input: - 240Vdc/ 10A Š DC Output: - 1000W@100-120V, +12.2V/ 81.5A, +12Vsb/ 2.5A - 1600W@180-199V, +12.2V/ 131A, +12Vsb/ 2.5A - 1800W@200-220V, +12.2V/ 147.5A, +12Vsb/ 2.5A - 2000W@221-240V, +12V/ 163.5A, +12Vsb/ 2.5A Operating...

  • Page 16: System Block Diagram

    System Block Diagram 8-Channel DDR4, 16 x DIMMs 8-Channel DDR4, 16 x DIMMs Up to 3200(1DPC)/ 2933(2DPC) MHz Up to 3200(1DPC)/ 2933(2DPC) MHz CPU_0 CPU_1 xGMI: 10.6GT/s, xGMI2: 16-20GT/s 4x16 GOP PCIe4.0 x16 PCIe4.0 x16 AMD MILAN AMD MILAN “Zen3” Core “Zen3”...

  • Page 17: Chapter 2 System Appearance

    Chapter 2 System Appearance Front View HDD#9 HDD#0 HDD#3 HDD#6 HDD#10 HDD#4 HDD#1 HDD#7 HDD#11 HDD#2 HDD#5 HDD#8 Description Front Panel LEDs and Buttons 3.5" HDD Bays Front USB 3.0 Ports • Refer to section 2-3 Front Panel LEDs and Buttons for a detailed description of the function of the LEDs.

  • Page 18: Rear View

    Rear View PSU1 PSU2 Description Description Mezzanine Slot (for OCP 3.0 Mezzanine Slot (for OCP 2.0 Card, Card, SFF Type, optional) optional) ID Button with LED VGA Port Server Management LAN Full-Height GPU Card Slot Port 1 GbE LAN Ports Full-Height GPU Card Slot USB 3.0 Port x 2 Full-Height GPU Card Slot...

  • Page 19: Front Panel Leds And Buttons

    Front Panel LEDs and Buttons No. Name Color Status Description Reset Button Press this button to reset the system. Press this button for the server to generate a NMI to the NMI button processor. If multiple-bit ECC errors occur, the server will effectively be halted.
  • Page 20 Green Indicates system is operating normally. Indicates a critical condition, may include: - System fan failure - System temperature Amber Indicates non-critical condition, may include: System - Redundant power module failure Blink Status LED - Temperature and voltage issue - Chassis intrusion Indicates system is not ready, may include: - POST error - NMI error...

  • Page 21: Rear System Lan Leds

    Rear System LAN LEDs Name Color Status Description Yellow 1 Gbps data rate 1GbE Green 100 Mbps data rate Speed LED 10 Mbps data rate Link between system and network or no access 1GbE Green Link/ Blink Data transmission or receiving is occurring Activity No data transmission or receiving is occurring...

  • Page 22: Power Supply Unit Led

    Power Supply Unit LED PSU LED State Description No AC power to all power supplies 1Hz Green Blinking AC present / only standby on / Cold redundant mode 2Hz Green Blinking Power supply firmware updateing mode AC cord unplugged or AC power lost; with a second power supply in parallel still with AC input power Amber Power supply critical event causing shut down:...

  • Page 23: Hard Disk Drive Leds

    Hard Disk Drive LEDs LED #1 LED #2 HDD Present RAID SKU LED #1 Locate Rebuilding HDD Access Fault (No Access) Green ON(*1) BLINK (*2) Disk LED (LED on Back Panel) Amber No RAID configuration Removed HDD Green ON(*1) (via HBA) Slot (LED on Amber Back Panel)
  • Page 24 This page intentionally left blank System Appearance - 24 -...

  • Page 25: Chapter 3 System Hardware Installation

    Chapter 3 System Hardware Installation Pre-installation Instructions Computer components and electronic circuit boards can be damaged electrostatic discharge. Working on computers that are still connected to a power supply can be extremely dangerous. Follow the simple guidelines below to avoid damage to your computer or injury to yourself. •...

  • Page 26: Removing And Installing The Chassis Cover

    Removing and Installing the Chassis Cover Before you remove or install the system cover • Make sure the system is not turned on or connected to AC power. Follow these instructions to remove the chassis cover: Remove the screw securing the chassis cover. Loosen the thumbnail screw securing the chassis cover.

  • Page 27: Removing And Installing The Fan Duct

    Removing and Installing the Fan Duct Follow these instructions to remove the fan duct: Lift up to remove the fan duct. To reinstall the fan duct, align the fan duct with the guiding groove. Push down the fan duct until it is firmly seated on the system.

  • Page 28: Removing And Installing The Heat Sink

    Removing and Installing the Heat Sink Read the following guidelines before you begin to install the heat sink: • Always turn off the computer and unplug the power cord from the power outlet before installing the heat sink to prevent hardware damage. •...

  • Page 29: Removing And Installing The Cpu

    Removing and Installing the CPU Read the following guidelines before you begin to install the CPU: • Make sure that the motherboard supports the CPU. • Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage.
  • Page 30 • Tighten the CPU cover screws in sequential order (1g2g3). • The screw tightening torque: 16.1 ± 1.2 kgf-cm (14.0± 1.0 lbf-in) System Hardware Installation - 30 -...

  • Page 31: Removing And Installing Memory

    Removing and Installing Memory Read the following guidelines before you begin to install the memory: • Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. • Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.

  • Page 32: Removing And Installing A Memory Module

    3-5-2 Removing and Installing a Memory Module Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. Be sure to install DDR4 DIMMs on to this motherboard.

  • Page 33: Dimm Population Table

    3-5-4 DIMM Population Table EPYC Memory Speed based on DIMM Population (One DIMM per Channel) DIMM Population DIMM Max EPYC 7003 Type DDR Frequency (MHz) DIMM 0 1R (1 Rank) 3200 RDIMM 2R or 2DR (2 Ranks) 3200 4DR (4 Ranks) 3200 LRDIMM 2S2R (4 Ranks)

  • Page 34: Removing And Installing The Pcie/Riser Card

    Removing and Installing the PCIe/Riser Card • Voltages can be present within the server whenever an AC power source is connected. This voltage is present even when the main power switch is in the off position. Ensure that the system is powered off and all power sources have been disconnected from the server prior to installing a PCI card.
  • Page 35 - 35 - System Hardware Installation...

  • Page 36: Installing The Mezzanine Card

    Installing the Mezzanine Card 3-7-1 Installing the OCP 3.0 Mezzanine Card Use of the following type of OCP 3.0 NIC is recommended: • OCP 3.0 SFF with pull tab • OCP 3.0 SFF with ejector latch Follow these instructions to install an OCP 3.0 Mezzanine card: Remove the two screws securing the OCP 3.0 card slot cover.

  • Page 37: Installing The Ocp 2.0 Mezzanine Card

    3-7-2 Installing the OCP 2.0 Mezzanine Card Follow these instructions to install an OCP 2.0 Mezzanine card: Remove the screw securing the OCP 2.0 card slot cover. Remove the slot cover from the system. Align the screw holes on the OCP 2.0 card with the heads of the stand-off screws ensuring that the ports on the card are properly fitted into the rear panel of the system.

  • Page 38: Removing And Installing The Hard Disk Drive

    Removing and Installing the Hard Disk Drive Read the following guidelines before you begin to install the hard disk drive: • Take note of the HDD tray orientation before sliding it out. • The tray will not fit back into the bay if it is inserted incorrectly. •...
  • Page 39 Follow these instructions to install a 2.5" hard disk drive: Press the release button. Extend the locking lever. Pull the locking lever in the direction indicated to remove the HDD tray. Align the hard disk drive with the positioning screw on the HDD tray. Secure the hard disk drive with five screws.

  • Page 40: Installing And Removing An M.2 Device

    Installing and Removing an M.2 Device WARNING: Installation of the thermal pad over the M.2 device is required when installing an M.2 device. Lack of the thermal pad may result in system overheat and throttle the system performance. CAUTION: The position of the stand-off screw will depend on the size of the M.2 device. The stand-off screw is pre-installed for 22110 cards as standard.

  • Page 41: Replacing The Fan Assembly

    3-10 Replacing the Fan Assembly • The image below shows the system image of R282-Z90. The same process applies to R282-Z91 and R282-Z90. Follow these instructions to replace a fan assembly: Flip the latches on the top of the fan outwards. Using the latches, lift up the fan assembly from the chassis.

  • Page 42: Removing And Installing The Power Supply

    3-11 Removing and Installing the Power Supply Before you remove or install the power supply unit: • Make sure the system is not turned on or connected to AC power. Follow these instructions to replace the power supply: Flip up and then grasp the power supply handle. Press the retaining clip on the right side of the power supply unit in the direction indicated.

  • Page 43: Cable Routing

    3-12 Cable Routing Onboard SATA Onboard SATA System Hardware Installation - 43 -...
  • Page 44 HDD Backplane Board Power HDD Backplane Board Signal - 44 - System Hardware Installation...
  • Page 45 Front Panel USB 3.0 Ports Front Panel LEDs and Buttons - 45 - System Hardware Installation...
  • Page 46 GPU Card Power System Hardware Installation - 46 -...

  • Page 47: Chapter 4 Motherboard Components

    Chapter 4 Motherboard Components Motherboard Components 15 16 10 11 Item Description Front Panel USB 3.0 Connector Front Panel Connector 2 x 4 Pin P12V GPU Power Connector 2 x 4 Pin P12V GPU Power Connector IPMB Connector Serial Port Cable Connector OCP Mezzanine Connector (OCP 3.0/SFF Type/Gen4 x16) BMC Firmware Readiness LED TPM Module Connector (SPI Interface)
  • Page 48 SlimLine SAS Connector (SLSAS_0/PCIe/SATA/Defined by SKUs) SlimLine SAS Connector (SLSAS_1/PCIe/SATA/Defined by SKUs) System Battery Riser Connector #1 (PCIe Gen4/x32 Slot) M.2 Connector (PCIe3 x4, Supports NGFF-22110) 2 x 4 Pin P12V GPU Power Connector 2 x 3 Pin Rear Back Plane Board Power Connector OCP Mezzanine Connector (OCP 2.0/Gen3 x8) Riser Connector #2 (PCIe Gen4/x32 Slot) Riser Connector #3 (PCIe Gen4/x16 Slot)

  • Page 49: Jumper Settings

    Jumper Settings NCSI Switch Onboard LAN OCP 2.0 Mezzanine OCP 3.0 Mezzanine Default Clear CMOS CLR_CMOS Enable HOST_SMBUS_SEL BIOS Defined PMBUS_SEL BIOS Defined BIOS_PWD Clear supervisor password Normal [Default] BIOS_RCVR BIOS recovery mode Normal [Default] - 49 - Motherboard Components...
  • Page 50 This page intentionally left blank Motherboard Components - 50 -...

  • Page 51: Chapter 5 Bios Setup

    Chapter 5 BIOS Setup BIOS (Basic Input and Output System) records hardware parameters of the system in the EFI on the motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup, saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features.
  • Page 52  Main This setup page includes all the items in standard compatible BIOS.  Advanced This setup page includes all the items of AMI BIOS special enhanced features. (ex: Auto detect fan and temperature status, automatically configure hard disk parameters.) ...

  • Page 53: The Main Menu

    The Main Menu Once you enter the BIOS Setup program, the Main Menu (as shown below) appears on the screen. Use arrow keys to move among the items and press <Enter> to accept or enter other sub-menu. Main Menu Help The on-screen description of a highlighted setup option is displayed on the bottom line of the Main Menu.
  • Page 54 Parameter Description BIOS Information Project Name Displays the project name information. Project Version Displays version number of the BIOS setup utility. Build Date and Time Displays the date and time when the BIOS setup utility was created. BMC Information BMC Firmware Version Displays version number of the BIOS setup utility.
  • Page 55 Parameter Description Total Memory Displays the total memory size of the installed memory. (Note1) Memory Speed Displays the frequency information of the installed memory. (Note1) VR Information Version Displays VR version information. AGESA PI Version PI Version Displays AGESA PI version information. Onboard LAN Information LAN1 MAC Address Displays LAN MAC address information.

  • Page 56: Advanced Menu

    Advanced Menu The Advanced menu display submenu options for configuring the function of various hardware components. Select a submenu item, then press [Enter] to access the related submenu screen. BIOS Setup - 56 -...

  • Page 57: Trusted Computing

    5-2-1 Trusted Computing Parameter Description Configuration Select Enable to activate TPM support feature. Security Device Support Options available: Enable/Disable. Default setting is Enable. SPI TPM Support Options available: Enabled/Disabled. Default setting is Enabled - 57 - BIOS Setup...

  • Page 58: Psp Firmware Versions

    5-2-2 PSP Firmware Versions The PSP Firmware Versions page displays the basic PSP firmware version information. Items on this window are non-configurable. BIOS Setup - 58 -...

  • Page 59: Legacy Video Select

    5-2-3 Legacy Video Select Parameter Description Select between onboard or external VGA support. OnBrd/Ext VGA Select Options available: Auto/Onboard/External. Default setting is Onboard. - 59 - BIOS Setup...

  • Page 60: Ast2500 Super Io Configuration

    5-2-4 AST2500 Super IO Configuration Parameter Description AST2500 Super IO Configuration Super IO Chip Displays the super IO chip information. BIOS Setup - 60 -...
  • Page 61 Parameter Description Press [Enter] to configure advanced items. Serial Port (Note1) Š – Enable/Disable the Serial Port (COM). When set to Enabled allows you to configure the Serial port 1/2 settings. When set to Disabled, displays no configuration for the serial port. –...

  • Page 62: S5 Rtc Wake Settings

    5-2-5 S5 RTC Wake Settings Parameter Description Enable or disable system wake on alarm event. Select Fixed Time, system will wake on the time (HH:MM:SS) specified. Select Dynamic Time and the Wake system from S5 system will wake at the current time plus an increase in minute(s). Options available: Disabled/Fixed Time.

  • Page 63: Serial Port Console Redirection

    5-2-6 Serial Port Console Redirection Parameter Description Select whether to enable console redirection for specified device. Console COM1/SOL / COM2 Console redirection enables the users to manage the system from a remote location. Redirection (Note) Options available: Enabled/Disabled. Default setting is Disabled. Selects a COM port for Legacy serial redirection.
  • Page 64 Parameter Description Bits per second Š – Selects the transfer rate for console redirection. – Options available: 9600/19200/38400/57600/115200. Default setting is 115200. Data Bits Š – Selects the number of data bits used for console redirection. – Options available: 7/8. Default setting is 8. Parity Š...
  • Page 65 Parameter Description Redirection COM Port Š – Selects a COM port to display redirection of Legacy OS and Legacy OPROM Messages. – Options available: COM1/SOL / COM2. Default setting is COM1/ SOL. Resolution Š Legacy Console Redirection – On Legacy OS, the number of rows and columns supported in Settings redirection.

  • Page 66: Cpu Configuration

    5-2-7 CPU Configuration Parameter Description CPU Configuration Enable/disable the CPU Virtualization. SVM Mode Options available: Enabled/Disabled. Default setting is Enabled. Controls the Secure Memory Encryption Enable (SMEE) function. SMEE Options available: Enabled/Disabled. Default setting is Enabled. CPU 0 Information Press [Enter] to view more information related to CPU 0. CPU 1 Information Press [Enter] to view more information related to CPU 1.

  • Page 67: Pci Subsystem Settings

    5-2-8 PCI Subsystem Settings - 67 - BIOS Setup...
  • Page 68 Parameter Description PCI Bus Driver Version Displays the PCI Bus Driver version information. Change the PCIe lanes. SLOT1_F / SLOT1_R / SLOT2_F / Options available: SLOT2_R / SLOT3 / OCP1 / OCP2 Auto / x16 / x8 x8 / x8 x4 x4 / x4 x4 x8 / x4 x4 x4 x4 Lanes (OCP2 Lanes only features Auto / x8 / x4 x4.) (Note1)

  • Page 69: Usb Configuration

    5-2-9 USB Configuration Parameter Description USB Configuration USB Module Version Displays the USB version. USB Controllers Displays the supported USB controllers. USB Devices Displays the USB devices connected to the system. Enable/disable the Legacy USB support fuction. AUTO option disables legacy support if no USB devices are connected.
  • Page 70 Parameter Description USB mass storage device Start Unit command time-out. Device reset time-out Options available: 10 sec/20 sec/30 sec/40 sec. Default setting is 20 sec. Maximum time the device will take before it properly reports itself to the Host Controller. "Auto" uses default value: for a Root port it is 100 ms, for Device power-up delay a Hub port the delay is taken from Hub descriptor.

  • Page 71: Nvme Configuration

    5-2-10 NVMe Configuration Parameter Description NVMe controller and Drive Displays the NVMe devices connected to the system. Information - 71 - BIOS Setup...

  • Page 72: Sata Configuration

    5-2-11 SATA Configuration BIOS Setup - 72 -...

  • Page 73: Network Stack Configuration

    5-2-12 Network Stack Configuration Parameter Description Enable/Disable the UEFI network stack. Network Stack Options available: Enabled/Disabled. Default setting is Enabled. Enable/Disable the Ipv4 PXE feature. Ipv4 PXE Support (Note) Options available: Enabled/Disabled. Default setting is Enabled. Enable/Disable the Ipv4 HTTP feature. Ipv4 HTTP Support (Note) Options available: Enabled/Disabled.

  • Page 74: Amd Mem Configuration Status

    5-2-13 AMD Mem Configuration Status Parameter Description Press [Enter] for configuration of advanced items. Channel A/BC/D/E/F/G/H Š – DIMM0 Presence – DIMM1 Presence CPU 0 – Chipset/Bank Interleave Dram EC Š Dram Parity Š Dimm Sensor Fine Grain Mode Š Press [Enter] for configuration of advanced items.

  • Page 75: Iscsi Configuration

    5-2-14 iSCSI Configuration Parameter Description Press [Enter] and name iSCSI Initiator. Only IQN format is accecpted. iSCSI Initiator Name Range: from 4 to 223 Add Attempt Press [Enter] for configuration of advanced items. Delete Attempt Press [Enter] for configuration of advanced items. Change Attempt Order Press [Enter] for configuration of advanced items.

  • Page 76: Tls Auth Configuration

    5-2-15 Tls Auth Configuration Parameter Description Press [Enter] for configuration of advanced items. Enroll Cert Š – Press [Enter] to enroll a certificate • Enroll Cert Using File • Cert GUID Server CA Configuration Input digit character in 1111111-2222-3333-4444- 1234567890ab format. –...

  • Page 77: Intel(R) I350 Gigabit Network Connection

    5-2-16 Intel(R) I350 Gigabit Network Connection - 77 - BIOS Setup...
  • Page 78 Parameter Description Press [Enter] to configure advanced items. Link Speed Š – Allows for automatic link speed adjustment. – Options available: Auto Negotiated/10 Mbps Half/10 Mbps Full/100 Mbps Half/100 Mbps Full. Default setting is Auto Negotiated. NIC Configuration Wake On LAN Š...

  • Page 79: Vlan Configuration

    5-2-17 VLAN Configuration - 79 - BIOS Setup...
  • Page 80 Parameter Description Press [Enter] to configure advanced items. Create new VLAN Š VLAN ID Š – Sets VLAN ID for a new VLAN or an existing VLAN. – Press the <+> / <-> keys to increase or decrease the desired values. The valid range is from 0 to 4094.

  • Page 81: Mac Ipv4 Network Configuration

    5-2-18 MAC IPv4 Network Configuration Parameter Description Indicates whether network address is configured successfully or not. Configured Options available: Disabled/Enabled. Default setting is Disabled. Enable DHCP Options available: Enabled/Disabled. Default setting is Enabled. (Note) Local IP Address Press [Enter] to configure local IP address. (Note) Local NetMask Press [Enter] to configure local NetMask.

  • Page 82: Mac Ipv6 Network Configuration

    5-2-19 MAC IPv6 Network Configuration Parameter Description Press [Enter] for configuration of advanced items. Interface Name Š Interface Type Š MAC address Š Host address Š Route Table Š Gateway addresses Š DNS addresses Š Interface ID Š Enter Configuration Menu –...

  • Page 83: Amd Cbs Menu

    AMD CBS Menu AMD CBS menu displays submenu options for configuring the CPU-related information that the BIOS automatically sets. Select a submenu item, then press [Enter] to access the related submenu screen. - 83 - BIOS Setup...

  • Page 84: Valhalla Common Options

    5-3-1 Valhalla Common Options Parameter Description Valhalla Common Options Press [Enter] for more options. Custom Core Pstates Š – Allows you to accept or decline custom core pstates. When accepted you can disable or customize ceratin pstates. Performance CCD/Core/Thread Enablement Š...
  • Page 85 Parameter Description From a workaroud for GCC/C000005 issue for XV Core on CZ A0, setting MSRC001_1029 Decode Configuration (DE_CFG) bit 14 RedirectForReturnDis [DecfgNoRdrctForReturns] to 1. Options available: Auto/1/0. Default option is Auto. Enable/Disable PFEH, cloak individual banks, and mask deferred error Platform First Error Warning interrupts from each bank.
  • Page 86 Parameter Description By default (Auto) the bronze workaround is applied. Bronze workaround: DbReq and PDM function as expected, breakpoint redirect capability compromised. Xtrig7 Workaround Silver workaround: DbReq, PDM, and breakpoint redirect function as expected, SCAN capability compromised. Options available: Auto/No Workaround/Bronze Workaround/Silver Workaround.

  • Page 87: Df Common Options

    5-3-2 DF Common Options Parameter Description Press [Enter] for configuration of advanced items. DRAM scrub time Š – Provides a value that is the number of hours to scrub memory. – Options available: Disabled/1 hour/4 hours/8 hours/16 hours/24 hours/48 hours/Auto. Default option is Auto. Poison scrubber control Š...
  • Page 88 Parameter Description Press [Enter] for more options. NUMA notes per socket Š – Specifies the number of desired NUMA (Non-uniform Memory Access) notes per socket. Zero will attempt to interleave the two sockets together. – Options available: NPS0/NPS1/NPS2/NPS4/Auto. Default option is Auto.
  • Page 89 Parameter Description Press [Enter] for more options. GMI encryption control Š – Control GMI link encryption. – Options available: Disable/Enable/Auto. Default option is Auto. xGMI encryption control Š – Control xGMI link encryption.Options available: Disable/Enable/ Auto. Default option is Auto. CAKE CRC perf bounds control Š...

  • Page 90: Umc Common Options

    5-3-3 UMC Common Options Parameter Description Press [Enter] for more options. Enforce POR Š – Press [Enter] to configure the enforcement of Plan Of Record (POR) which enables enforcement of POR restrictions for DDR4 frequency and voltage programming. DRAM Controller Configuration Š...
  • Page 91 Parameter Description Press [Enter] for more options Chipselect Interleaving Š – Interleave memory blocks across the DRAM chip slects for node 0 – Options available: Disabled/Auto. Default option is Auto. BankGroupSwap Š – Configures the BankGroupSwap. BankGroupSwap (BGS) is a memory mapping option in AGESA that alters how applications get assigned to physical locations within the memory modules.

  • Page 92: Nbio Common Options

    5-3-4 NBIO Common Options Parameter Description NBIO Common Options Enable/Disable IOMMU. IOMMU Options available: Enabled/Disabled. Default setting is Disabled. AER must be enabled for ACS enable to work. ACS Enable Options available: Enable/Disabled/Auto. Default option is Auto. Enables Alternative Routing ID Interpretation. PCIe ARI Support Options available: Disable/Enable/Auto.
  • Page 93 Parameter Description Press [Enter] for more options. Determinism Control Š – Auto = Use the fused determinism, Manual = User can set customized determinism. – Options available: Manual/Auto. Default option is Manual. cTDP Control Š – Auto = Use the fused TDP, Manual = User can set customized TDP.
  • Page 94 Parameter Description Press [Enter] for more options. NBIO RAS Global Control Š – Options available: Manual/Auto. Default option is Auto. NBIO RAS Control Š – 0 = Disabled, 1 = MCA, 2 = Legacy. – Options available: Disabled/MCA/Legacy. Default option is MCA. Egress Poison Severity High Š...
  • Page 95 Parameter Description System Hub Watchdog Timer Š – Enter a value. This value specifies the timer interval of the SYSHUB watchdog timer in miliseconds. SLINK Read Response OK Š – This value specifies whether SLINK read response errors are converted to an Okay response. When this value is set to TRUE, read response errors are converted to Okay responses with data of all FFs.
  • Page 96 Parameter Description Sync Flood on PCIe Fatal Error Š – When 'Sync Flood on PCIe Fatal Error' is True, PcdAmdPcieSyncFloodOnFatal should be set to True. When 'Sync NBIO RAS Common Options Flood on PCIe Fatal Error' is False, PcdAmdPcieSyncFloodOnFatal (continued) should be set to False.

  • Page 97: Fch Common Options

    5-3-5 FCH Common Options Parameter Description FCH Common Options SATA Enable Š – Enable or disable OnChip SATA controller. – Options available: Disabled/Enabled/Auto. Default setting is Auto. SATA RAS Support Š – Enable or disable SATA RAS support. – Options available: Disabled/Enabled/Auto. Default setting is Auto. SATA Configuration Options Sata Disabled AHCI Prefetch Function Š...
  • Page 98 Parameter Description Press [Enter] for more options. XHCI Controller0 Enable Š – Enable or disable USB3 controller. – Options available: Enabled/Disabled/Auto. Default setting is Auto. XHCI Controller1 Enable Š USB Configuration Options – Enable or disable USB3 controller. – Options available: Enabled/Disabled/Auto. Default setting is Auto. USB ecc SMI Enable Š...
  • Page 99 Parameter Description Press [Enter] for more options. eMMC/SD Configure Š – Options available: Disabled/SD Normal Speed/SD High Speed/SD UHSI-SDR50/SD UHSI-DDR50/SDUHSI-SDR104/eMMC Emmc Backward Compatibility/eMMC High Speed SDR/eMMC High Speed DDR/eMMC HS200/eMMCHS400/eMMC HS300/Auto. Default setting is Auto. eMMC Options Driver Type Š –...

  • Page 100: Ntb Common Options

    5-3-6 NTB Common Options Parameter Description NTB Common Options Enable or disable OnChip SATA controller. NTB Enable Options available: Auto/Enable. Default setting is Auto. BIOS Setup - 100 -...

  • Page 101: Soc Miscellaneous Control

    5-3-7 SOC Miscellaneous Control Parameter Description Soc Miscellaneous Control Enable = Enable ConsoleOut Function for ABL Disable = Disable ConsoleOut Function for ABL ABL Console Out Control Auto = Keep default behavior Options available: Disable/Enable/Auto. Default setting is Auto. - 101 - BIOS Setup...

  • Page 102: Amd Pbs Option Menu

    AMD PBS Option Menu AMD PBS Option menu displays submenu options for configuring the function of AMD PBS. Select a submenu item, then press [Enter] to access the related submenu screen. Parameter Description AMD PBS Press [Enter] for advanced configurations. Enable or disable SPI Locking for protect ROM part.

  • Page 103: Ras

    5-4-1 RAS Parameter Description Enable or disable Periodic SMI for polling [MCA Threshold] error. RAS Periodic SMI Control Options Available: Disabled/Enabled. Default option is Enabled. Enter a value. Limits the number of [MCA Threshold and Deferred Error SMI source] SMI Threshold per a unit of time (Defined by [SMI Scale]).
  • Page 104 Parameter Description PCIe UnCorr GHES Notify Notification type for PCIe uncorrected errors. Type Options Available: Polled/NMI. Default option is NMI. PCIe Root Port Corr Err Mask Enter a value. Intialize the PCIe AER Corrected Error Mask register of Root Port. PCIe Root Port UnCorr Err Enter a value.

  • Page 105: Chipset Setup Menu

    Chipset Setup Menu Chipset Setup menu displays submenu options for configuring the function of the SoC. Select a submenu item, then press [Enter] to access the related submenu screen. Parameter Description PCIe Link training in 1 or 2 steps. PCIe Link Training Type Options available: 1 Step/2Step.

  • Page 106: Server Management Menu

    Server Management Menu Parameter Description FRB-2 Timer FRB-2 timer (POST timer). Configure the FRB2 Timer timeout. Options available: 3 minutes/4 minutes/5 minutes/6 minutes. Default setting is 6 FRB-2 Timer minutes. timeout (NOTE) This item is configurable when FRB-2 Timer is set to Enabled. Configure the FRB2 Timer policy.
  • Page 107 Parameter Description View FRU Press [Enter] to view the advanced items. Information BMC network Press [Enter] to configure advanced items. configuration IPv6 BMC Network Press [Enter] to configure advanced items. Configuration - 107 - BIOS Setup...

  • Page 108: System Event Log

    5-6-1 System Event Log Parameter Description Enabling / Disabling Options Change this item to enable or disable all features of System Event SEL Components Logging during boot. Options available: Enabled/Disabled. Default setting is Enabled. Erasing Settings Choose options for erasing SEL. Erasing SEL Options available: No/Yes, On next reset/Yes, On every reset.

  • Page 109: View Fru Information

    5-6-2 View FRU Information The FRU page is a simple display page for basic system ID information, as well as System product information. Items on this window are non-configurable. (Note) The model name will vary depends on the product you purchased. - 109 - BIOS Setup...

  • Page 110: Bmc Network Configuration

    5-6-3 BMC Network Configuration Parameter Description BMC network configuration Lan Channel 1 Select to configure LAN channel parameters statically or dynamically (DHCP). Do nothing option will not modify any BMC network parameters Configuration Address source during BIOS phase. Options available: Unspecified/Static/DynamicBmcDhcp. Default setting is DynamicBmcDhcp.

  • Page 111: Ipv6 Bmc Network Configuration

    5-6-4 IPv6 BMC Network Configuration Parameter Description IPv6 BMC Network Configuration IPv6 BMC Lan Channel 1 Enable/Disable IPv6 BMC LAN channel function. When this item is IPv6 BMC Lan Option disabled, the system will not modify any BMC network during BIOS phase. Options available: Unspecified/Disable/Enable.

  • Page 112: Security Menu

    Security Menu The Security menu allows you to safeguard and protect the system from unauthorized use by setting up access passwords. There are two types of passwords that you can set: • Administrator Password Entering this password will allow the user to access and change all settings in the Setup Utility. •...

  • Page 113: Secure Boot

    5-7-1 Secure Boot Parameter Description System Mode Displays the system is in User mode or Setup mode. Enables/Disables Secure Boot. The mode change requires a platform Secure Boot reset. Options available: Disabled/Enabled. Default setting is Disabled. Secure Boot requires all the applications that are running during the booting process to be pre-signed with valid digital certificates.
  • Page 114 Parameter Description Factory Key Provision Š – Installs factory default Secure Boot keys after the platform resets and the system is in Setup Mode. – Options available: Disabled/Enabled. Default setting is Disabled. Restore Factory Keys Š – Installs factory default Secure Boot key databases. It will force the system in User Mode.

  • Page 115: Boot Menu

    Boot Menu The Boot menu allows you to set the drive priority during system boot-up. BIOS setup will display an error message if the legacy drive(s) specified is not bootable. Parameter Description Boot Configuration Number of seconds to wait for setup activation key. 65535 (0xFFFF) Setup Prompt Timeout means indefinite waiting.

  • Page 116: Uefi Network Drive Bbs Priorities

    Parameter Description UEFI Network Drive BBS Press [Enter] to configure the boot priority. Priorities UEFI Application Boot Priorities Press [Enter] to configure the boot priority. BIOS Setup - 116 -...
  • Page 117 5-8-1 UEFI NETWORK Drive BBS Priorities The UEFI network drive BBS priorities submenu allows you to specify the boot device priority from the available UEFI network drives during system boot-up. BIOS setup will display an error message if the legacy drive(s) specified is not bootable.
  • Page 118 5-8-2 UEFI Application Boot Priorities The UEFI application boot priorities submenu allows you to specify the boot device priority from the available UEFI applications during system boot-up. BIOS setup will display an error message if the legacy drive(s) specified is not bootable. BIOS Setup - 118 -...

  • Page 119: Save & Exit Menu

    Save & Exit Menu The Exit menu displays the various options to quit from the BIOS setup. Highlight any of the exit options then press [Enter]. Parameter Description Save Options Saves changes made and closes the BIOS setup. Save Changes and Exit Options available: Yes/No.

  • Page 120: Bios Post Beep Code (Ami Standard)

    5-10 BIOS POST Beep code (AMI standard) 5-10-1 PEI Beep Codes # of Beeps Description Memory not Installed. Memory was installed twice (InstallPeiMemory routine in PEI Core called twice) Recovery started DXEIPL was not found DXE Core Firmware Volume was not found Recovery failed S3 Resume failed Reset PPI is not available...

Table of Contents