Trouble indications
The indicator illuminates and a beep sounds to inform you of internal abnormalities.
No power
⇒
Problem with projector
(OFF)
•
Unplug the power cord, and contact your dealer.
Lamp went out during use, or won't come on
⇒ Lamp temperature is high so that it is difficult to turn on, the
(Red
lifetime of the lamp has ended or the projector is malfunctioning.
(Red lit)
flashing)
•
Unplug the power cord and wait for a short while, then turn the
or
power back on.
•
If a lamp burns out, replace it with a new one.
(Red lit)
(Red lit)
Power went out during use
⇒ Internal overheating, or the outside temperature is too high.
•
Make sure the projector is placed so that the air intake and
(Red
(Red lit)
flashing)
exhaust are not blocked.
•
Unplug the power cord and wait for a short while, then turn the
power back on.
The
icon will appear before the power goes out.
Power went out during use
⇒ Problem with internal cooling fan.
•
Unplug the power cord, and contact your dealer.
(Green
(Red lit)
flashing)
The
icon will appear before the power goes out.
Power went out during use, or power won't come on
⇒ The lamp cover is not properly attached.
(Orange
•
Unplug the power cord, and reattach the lamp cover.
(Red lit)
flashing)
Power went out during use
⇒ Problem inside the projector.
(Orange lit)
•
Unplug the power cord and wait for a short while, then turn the
(Red lit)
or
power back on.
•
If the above action does not clear the problem, unplug the power
(Orange
cord, and contact your dealer.
flashing)
The
icon will appear before the power goes out.
Note
•
After there is an abnormal indication, the abnormal status remains until the power cord
is unplugged.
Others
p.92
96
Troubleshooting
If you think something is wrong, check the followings before contacting customer service.
Please see "Trouble indications"
as well.
p.96
If This Happens
No power
•
Is the power cord plugged in? Is it connected to the projector?
•
Is the outer lamp cover attached properly?
Power goes out
•
Is the ambient temperature high?
during use
•
Is the air intake or air exhaust blocked?
No picture
•
Is the input source selected correctly? (When [Auto input search]
is [Off])
p.42
•
Is the mute function on?
•
Is the brightness setting minimized?
•
Are the connections set up correctly?
•
Are all the connected devices functioning properly?
No audio
•
Is the mute function on?
•
Is the volume setting minimized?
•
Are the connections set up correctly?
•
Are all the connected devices functioning properly?
Picture not
•
Is the input signal supported by the projector?
displayed
•
Is there something generating an abnormal video signal, for
correctly
instance the video tape?
Picture blurred
•
Is the lens dirty?
Part of picture
•
Is the lens focus adjusted optimally?
out of focus
•
Is the projection distance within the projector's supported range?
p.22 p.23
•
Is the projector's screen placement angle tilted too far?
•
Are the sharpness or sampling phase adjustments off?
Image is dark
•
Are the brightness or contrast adjustments off?
•
Is the lamp nearing the end of its service life?
•
Is the RGB input range set properly?
Colors too light
•
Are the color, R-level, G-level, or B-level adjustments off?
Bad shading
•
Is the screen dirty?
•
Is the blackboard mode set properly?
•
Is the lamp nearing the end of its service life?
Control panel key
•
Is the key lock function on?
doesn't work
Check
p.92
p.96
p.96
p.33
p.37
p.24
p.33
p.29
p.24
p.100 p.101
p.95
p.29
p.29
p.37 p.38
p.37
p.45
p.37
p.39
p.45
p.43
97
p.37