Displaying Information (Status Display) - Toshiba TDP-T420U Owner's Manual

Using the menus (Continued)
Default setting 2 menu
Item
Projection
Sets projection mode in accordance with Placement Style.
mode
(Standard)
Fan mode Sets the cooling fan speed.
Remote control When  projectors are used and controlled by the remote control respectively,
this menu sets the code for the projector and the remote control.
[ or : Enter setting]
[ :Select OK to end
Press [Cancel] to return.
Key lock Lock the control panel buttons.
[ or : Enter setting]
[
:Select OK to end
Press [Cancel] to return.
Lamp power
Set the lamp power.
Reset all
Press . (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password
Password setting p.33
Press . Password registration/Password setting
Detailed description
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise
gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500
meters above sea level).
• Do not set Fan mode to [High] when using the projector at a lower altitude.
[Remote control]
Sets a remote control code from  types. You can set each code respectively for up to
 projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
• You cannot operate the remote control if the codes of the projector and the remote
control do not match.
Remote control code setting for remote control
Set the same remote control code switch as the projector.
Description
p.21
(Rear) (Ceiling)
Standard
[ ] [ : Confirm]
: Select from 1, 2
]
[ : Select On/Off ] [ : Confirm]
]
Low Standard
Yes
p.16 p.17
4
[Key lock]
Protect from operating errors by locking on the control panel buttons of the projector.
(The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly operation
(Rear ceiling)
with the control panel buttons is disabled.
To release the key lock, set the [Key lock] to [Off] using remote control. Pressing
•
High
the [RETURN] button on the projector for 10 seconds also sets the [Key lock] to [Off].
(When operating the main unit, the  indicators of LAMP and TEMP light in orange
for  seconds, and at the same time the projector beeps.).
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling
fan noise gets quieter.

Displaying Information (Status display)


This displays information about the input signal, lamp use time, etc.
Item
No
Input
Mode name
Resolution
Frequency
Sync
Signal format
Video mode
Lamp time
Lamp reset count
Total time
Version
Notes
1: The mode of supported RGB signals
: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the displayed time approaches ,000
hours, consult with a dealer about getting replacement for:
TLPLW40 (sold separately).
4: [Version] shows the version of the projector's internal control program. This version will
be requested for customer service purposes.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
"Yes": displayed, "No": not displayed
Digital (DVI) Analog (D-SUB)(DVI)
Description
RGB Y/P /P
B R
Input source name Yes Yes
[Note 1]
RGB input mode Yes No
Resolution (in dots) Yes No
Sync frequency Yes No
[Note ]
Sync signal polarity Yes No
Y/P /P signal format No Yes
B R
Color method of video signal No No
[Note ]
Time of lamp use Yes Yes
The count for lamp replacement Yes Yes
The total time that this
Yes Yes
projector is used.
[Note 4]
Firmware version Yes Yes
is shown.
p.53
4
Video S-video
RGB Y/P /P
B R
Yes Yes Yes Yes
Yes No No No
Yes No No No
Yes No No No
Yes No No No
No Yes No No
No No Yes Yes
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes Yes Yes Yes