Timer Recording - Toshiba MW26G71 Owner's Manual

Timer recording

Timer recording can be programmed on-screen with the remote control.
The built-in timer allows automatic unattended recording of up to 8
programs within 1 month.
Timer recording
Preparation:
• Press TV/VCR to select the TV/VCR mode.
• Load a cassette tape with the erase prevention tab
intact.
• Check the time and date are correct
Example:
Program a timer recording for 23rd day, channel 125
(Cable TV), 7:00 - 9:30 PM (Tape speed : SLP).
1
Press MENU, then press
VCR SETUP menu.
2
Press or to select "TIMER REC SET", then
press .
3
Press or to select one of the program line,
then press ENTER.
If you return to VCR SETUP menu,
selet "VCR SETUP" then press
4 Press or to select the date, then press
5U30101B [E]p51-54
.
24
or to select
VCR SETUP
TIMER REC SET
AUTO REPEAT OFF
: SELECT : ADJUST
RETURN : END
VCR SETUP
TIMER REC SET
AUTO REPEAT OFF
: SELECT : ADJUST
RETURN : END
T I M E R R E C S E T
D AT E S TA R T E N D C H S P E E D
V C R S E T U P
: S E L E C T
E N T E R : S E T R E T U R N : E N D
.
.
TIMER REC SET
DATE 2 3 ( T H U )
START 8 : 3 0 AM
END Ð Ð : Ð Ð
CH 0 1 2
SPEED S P
: SELECT : ADJUST
ENTER : SET RETURN : END
53
5
Set the start time, end time, channel and tape
speed as in step 4.
Then press ENTER.
Notes:
• Press to move cursor
backward for correction.
• To record from external
source set the channel to "L1"
or "L2".
6
To set the timer for another program, repeat
steps 3 to 5 to set another program.
7 Press TIMER REC. The TIMER REC indicator
will light. The Timer is programed, when the
programed time is reached, the recording is
automatically started.
To cancel timer recording, press the
button again and TIMER REC
indicator will go out.
Notes:
• The VCR section cannot be used while the TIMER REC in-
dicator is lit. If you want to use the VCR operation, press
TIMER REC to deactivate the timer.
• When the clock is not set, you cannot select "TIMER REC".
In this case, set the clock (see pages 21~23).
• After a power failure or disconnection of the power plug, all
programmed recording setting and time display will be lost
upon resumption of power. In this case, reset the clock (see
pages 21~23) and reprogram any timer recordings.
• If you want to correct the digits while setting, press
until the item you want to correct, then press
correct the desired setting.
• If programming is performed without a tape in the unit, or
with a tape without an erase prevention tab, the Timer Re-
cording is not possible. If a tape without an erase prevention
tab is in the unit, the tape will be ejected.
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs and other materials,
is prohibited under the Copyright Laws of the United States
and other countries, and may subject you to civil and/or crimi-
nal liability.
4/1/05, 3:27 PM
TV/VCR
ENTER
/ / /
MENU
TIMER REC
TIMER REC SET
DATE 2 3 ( T H U )
START 7 : 0 0 PM
END Ð 9 : 3 0 PM
CH 1 2 5
SPEED S L P
: SELECT : ADJUST
ENTER : SET RETURN : END
TIMER REC SET
DATE START END CH SPEED
2 3 T H 7 : 0 0 P M 9 : 3 0 P M 1 2 5 S L P
VCR SETUP
: SELECT CANCEL : DELETE
ENTER: SET RETURN : END
or
or to
53