Page 1 ® Satellite User’s Guide If you need assistance: ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see page 218 in this guide. Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
Page 2 If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA INFORMATION SYSTEMS (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE.
Page 3: Fcc Notice
Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used...
Page 4: Type Of Service
Industry Canada Requirement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada. FCC Requirements The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems.
Page 5: Fax Branding
FCC. In the event repairs are ever needed on your modem, they should be performed by Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba.
Page 6: Wireless Interoperability
USOC RJ11C. Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖...
Page 7: Wireless Lan And Your Health
Regulatory Information The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.
Page 8 co-located with any other transmitter that has not been tested with this device. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. L ‘utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’...
Page 9 Gebruik buiten gebouw alleen op kanalen 10 (2457 MHz) en 11 (2462 MHz). Voor privé-gebruik buiten gebouw over publieke groud over afstand kleiner dan 300m geen registratie bij BIPT/IBPT nodig; voor gebruik over afstand groter dan 300m is wel registratie bij BIPT/IBPT nodig.
Page 10 Caution: Exposure to Radio Frequency Radiation The Toshiba Wireless LAN Mini PCI Card will be installed with one of two types of antennas. The both of antenna types, when installed are located at the upper edge of the LCD screen.
Page 11 for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.
Page 12: Device Authorization
This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916...
Page 13: Interference Statement
❖ Consult the dealer or an experienced radio/TV technician for help. Toshiba is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Toshiba Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by Toshiba.
Page 14 Approved Countries/Regions for use for the Atheros AR5001X Mini PCI Wireless network adapter This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. NOTE This device works on passive scan only.
Page 15 Mexico Norway Singapore Switzerland Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Page 16: Bluetooth Wireless Technology Interoperability
Always use Bluetooth™ cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or http://www.pcsupport.global.toshiba.com in the United States for...
Page 17: Bluetooth Wireless Technology And Your Health
WirelessLAN. Please contact Toshiba PC product support on Web site http:// www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or http:// www.pcsupport.global.toshiba.com in the United States for more information. Bluetooth wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy.
Page 18 The radiated output power of the Bluetooth™ Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth™ Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 19 Nevertheless, it is advised to use the Bluetooth™ Card from TOSHIBA in such a manner that human contact during normal operation is minimized. NOTE Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment.
Page 20 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916...
Page 21 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wireless module into other device. DVD-ROM, multi-function drive safety instructions The DVD-ROM and multi-function drives employ a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
Page 22 This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 23 DirectShow are registered trademarks, and Windows Media is a trademark of Microsoft Corporation. LapLink is a registered trademark of Traveling Software, Inc. Dolby - Manufactured by Toshiba under license from Dolby Laboratories/ Dolby and the double-D symbol are trademarks of Dolby Laboratories. TouchPad is a trademark of Synaptics, Inc.
Page 24: Table Of Contents
Contents Introduction ...33 This guide ...33 Safety icons ...34 Other icons used...35 Other documentation ...35 Service options ...36 Chapter 1: Finding Your Way Around ...37 Making sure you have everything...37 Front with the display closed ...38 Back ...39 Right side...40 Left side ...41 Front with the display open...42 Front panel lights ...43...
Page 25 Keeping yourself comfortable ...48 Precautions...51 Setting up your computer ...53 Setting up your software...53 Registering your computer with Toshiba ...55 Adding external devices ...55 Connecting the AC adapter...56 Charging the main battery...58 Using the computer for the first time ...59 Opening the display panel ...59...
Page 26 Starting again after Shut down ...97 Using Hibernation ...97 Starting again from Hibernation mode ...99 Using Stand by ...100 Going into Stand by mode more quickly ...101 Starting again from Stand by ...101 Toshiba’s online resources ...102 ® special keys...78...
Page 27 Chapter 4: Mobile Computing ...103 Toshiba’s energy-saver design...103 Running the computer on battery power ...103 Power management ...105 Charging the battery ...105 Charging the RTC battery...106 Monitoring battery power ...107 Determining remaining battery power...107 Conserving battery power ...108 What to do when the battery runs low ...109 Setting battery alarms...110...
Page 28 Contents Lesson 8: Closing programs ...132 Lesson 9: Creating shortcuts ...133 Creating a shortcut to the Calculator...133 Creating a shortcut to the Character Map ...134 Lesson 10: Changing the screen saver...136 Lesson 11: Setting the date and time...138 Lesson 12: Removing objects from the desktop ...140 Lesson 13: Using System Restore ...142 Lesson 14: If I am lost, what do I do? ...143 Windows...
Page 29 Adding Music from Your Hard Drive to Playing Digital Music Files ...175 Finding Music Files in My Music ...176 Playing a Song ...177 Setting Up an Automatic Disc Jockey ...177 Finding and Playing an Album...178 Creating a Playlist ...179 Displaying Your Pictures...180 Viewing a Slide Show...181 Sorting your Pictures ...181 Watching Your Digital Movies...182...
Page 30 Contents Exchanging data with another computer...205 Transferring files using a parallel port Getting help transferring files...205 Connecting to the Internet ...206 An overview of using the Internet ...207 The Internet ...207 The World Wide Web ...207 Internet Service Providers...208 Signing up with an Internet Service Provider .208 Surfing the Internet...208 Internet features...209 Uploading and downloading files on...
Page 31 Modem problems...241 Develop good computing habits ...241 If you need further assistance...243 Before you call ...243 Contacting Toshiba ...244 Other Toshiba Internet Web sites ...245 Toshiba’s worldwide offices...245 Appendix A: Hot Keys...249 Instant password security...249 Without a password ...249 With a password ...249 Maintaining security when the battery is not Sound ...251...
Page 32 Enabling a wireless device ...255 Disabling or enabling the TouchPad ...255 Keyboard hot keys ...255 Appendix B: Power Cable Connectors... 256 Appendix C: Using ConfigFree™ with your Toshiba Computer ... 257 Getting Started...258 ConfigFree Main Screen ...258 Starting ConfigFree ...259 Configuring ConfigFree ...259 ConfigFree Utilities...260...
Page 33: Introduction
Internet access. This guide contains information about your operating system and how it functions with your Toshiba computer. For specific information on the software, see the Microsoft booklet that shipped with your computer.
Page 34: Safety Icons
Introduction Safety icons If you are new to computers, or have not used a notebook computer before, read through the first couple of chapters to familiarize yourself with the components of the computer and how to turn it on. After that, seek out whatever interests you most.
Page 35: Other Icons Used
Guides for other programs that may come preinstalled on your computer or that are available for installation on your Recovery media. ❖ For accessory information, visit Toshiba's Web site at toshiba.com. ❖ The Microsoft documentation which explains the features of the operating system.
Page 36: Service Options
Introduction Service options Service options Toshiba offers a full line of service options built around its SelectServ the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com.
Page 37: Chapter 1: Finding Your Way Around
Chapter 1 Finding Your Way Around This chapter presents a “grand tour” of your notebook computer. It serves as a reference when you need to locate specific parts of the computer. Making sure you have everything Before doing anything else, consult the Quick Start card provided with your system to make sure you received everything.
Page 38: Front With The Display Closed
Finding Your Way Around Front with the display closed Front with the display closed CD/DVD control buttons The display latch keeps the display panel closed and locked. To open the display panel, slide the display latch to the right and raise the panel. The CD/DVD control buttons allow you to play CDs and DVDs with the computer turned on through the preinstalled operating systems.
Page 39: Back
Back Modem port USB ports LAN port The DC IN port is where you plug in the AC adapter for either operating the computer on external power or charging the battery. The RGB (monitor) port lets you connect an external monitor.
Page 40: Right Side
Finding Your Way Around Right side The cooling vent prevents the computer’s central processing unit (CPU) from overheating so that it can continue to perform at maximum speed. To prevent possible overheating of the CPU, do not block the cooling vents. Right side The PC Card slot supports one Type I, Type II, or Type III PC Card.
Page 41: Left Side
Finding Your Way Around Left side as a printer or another computer that has a compatible infrared port. The security lock slot allows you to attach an optional ® PORT- Noteworthy computer lock cable to your computer for securing it to a large, heavy object such as your desk. Left side Microphone jack Headphone jack...
Page 42: Front With The Display Open
The power button turns the computer on and off. Holding down the power button for four seconds resets the computer. The Internet button launches your default Internet browser. The TOSHIBA Console button allows quick access to various functions. The One Touch TV Out button activates an external display device, such as a TV, when connected to the S-video port.
Page 43: Front Panel Lights
Finding Your Way Around Front with the display open The function keys, when used with the key, activate several different system functions. For more information, see “Hot Keys” on page 249. The front panel lights and system indicator lights provide information about various system functions.
Page 44: Indicator Lights
Finding Your Way Around Front with the display open amber while the battery is being charged. It does not glow if the external power source is disconnected or if the battery is completely discharged. For more information on determining remaining battery power, see page 107.
Page 45: Underside
on the top of the key. For more information, see cursor control overlay” on page The numeric mode light glows when the numeric overlay is on. When this light is on, pressing an overlay key types the white number printed on the key instead of typing the letter printed on the top of the key.
Page 46 Finding Your Way Around Underside The hard disk drive is the computer’s permanent data storage device. To prevent possible CPU overheating, do not block the cooling vents when the computer is in use. The battery pack contains the battery. For information about replacing the battery, see page 111.
Page 47: Chapter 2: Getting Started
Chapter 2 Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety of circumstances and locations.
Page 48: Keeping Yourself Comfortable
AC power source, and let it dry out completely before turning it on again. If the computer does not operate correctly after you turn it back on, contact a Toshiba Authorized Service Provider. Keeping yourself comfortable Strain and stress injuries are becoming more common as people spend more time using their computers.
Page 49 ❖ If you are using an external monitor, the top of the display should be no higher than eye level. ❖ If you use a paper holder, set it at about the same height and distance as the screen. Seating and posture When using your computer, maintain good posture with your body relaxed and your weight distributed evenly.
Page 50 Getting Started Selecting a place to work ❖ Adjust the back of your chair so that it supports the lower curve of your spine. If necessary, use a cushion to provide extra back support. Lower-back-support cushions are available at many office supply stores. ❖...
Page 51: Precautions
Work habits The key to avoiding discomfort or injury from strain is to vary your activities. If possible, schedule a variety of tasks into your working day. Finding ways to break up the routine can reduce stress and improve your efficiency. ❖...
Page 52 Getting Started Selecting a place to work ❖ Some PC Cards can become hot with prolonged use. If two cards are installed, both can become hot even if only one is being used. Overheating of a PC Card can result in errors or instability in its operation.
Page 53: Setting Up Your Computer
Setting up your computer TECHNICAL NOTE: You must complete all set up steps up to “Setting up your software” on page 53 or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC cards.
Page 54 A window will display asking if you wish to register with Toshiba and Microsoft. Click Yes to register, or No to exit the process. If you click No, you may register with Toshiba by clicking the NOTE Register with Toshiba icon on the desktop.
Page 55: Registering Your Computer With Toshiba
Toshiba warranty worldwide at no charge to you. You can register your computer with Toshiba during the start-up process or by clicking on the icon on the desktop at a later time.
Page 56: Connecting The Ac Adapter
Wash hands after handling. Use only the AC adapter supplied with your computer or an equivalent adapter that is compatible. Use of any incompatible adapter could damage your computer. Toshiba assumes no liability for any damage caused by use of an incompatible adapter.
Page 57 Hold the power cable by its plug when you connect/disconnect it. Do NOT pull the cable itself. Doing so may damage the power cable and result in a short circuit or electric shock. To connect AC power to the computer: Connect the power cable to the AC adapter.
Page 58: Charging The Main Battery
Getting Started Charging the main battery Damaged power cables can cause fire or electric shock. Never modify, forcibly bend, place heavy objects on top of, or apply heat to the power cable. If the power cable becomes damaged or the plug overheats, discontinue use.
Page 59: Using The Computer For The First Time
Using the computer for the first time Opening the display panel Slide the display latch to the right and lift the display panel Opening the display panel To avoid damaging the display panel, don’t force it beyond the point where it moves easily. Never lift or move the computer using the display panel.
Page 60: Using The Touchpad
Getting Started Using the computer for the first time When you turn on the computer for the first time, don’t turn off NOTE the power again until the operating system has loaded completely. The AC power indicator glows when the computer is connected to an external power source.
Page 61: Control Buttons
❖ To move the cursor to the right side of the page, slide your finger across the TouchPad from left to right. ❖ To move it to the left side, slide your finger from right to left. Because the TouchPad is much smaller than the display NOTE screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad...
Page 62: Installing Additional Memory (Optional)
Additional memory comes in various capacities (to stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at “Hot Keys” on page 249).
Page 63 Installing additional memory (optional) pcsupport.toshiba.com). There are two memory slots. Your system may have both slots occupied. If you use the computer for a long time, the memory modules will become hot. If this happens, let the modules cool to room temperature before you replace them.
Page 64 Getting Started Installing additional memory (optional) Using a standard Phillips no. 1 screwdriver, unscrew the two screws that secure the expansion memory slot cover, then remove the memory slot cover. Removing the memory slot cover Put the screws and the cover in a safe place so that you can retrieve them later.
Page 65 Installing additional memory (optional) Inserting the memory module Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems. Replace the expansion memory slot cover. Replace the screws and tighten them. Turn the computer over and reconnect any cables you removed.
Page 66: Removing A Memory Module
Getting Started Installing additional memory (optional) Removing a memory module Follow steps 1 through 6 in memory (optional)” on page Gently push the memory locks outward until the memory module pops up. Removing the memory module Gently pull the memory module diagonally to pull it out of the slot.
Page 67: Connecting A Printer
Connecting a printer Read the documentation that came with your printer. Follow NOTE the manufacturer’s instructions when connecting a local printer. You must supply the proper printer cable. If one did not come NOTE with your printer, you may purchase one from an electronics or computer store.
Page 68: Setting Up A Printer
Getting Started Setting up a printer Plug the USB connector into one of the USB ports on your computer Plug the printer’s power cable into a live AC outlet. To connect a parallel printer: Connecting the parallel printer cable while the computer is on may damage the printer, the computer, or both.
Page 69 Select Printers and Faxes. The Printers and Faxes window appears. Sample Printers and Faxes window Click Add Printer. The Add Printer Wizard starts. Sample Add Printer Wizard Getting Started Setting up a printer...
Page 70 Getting Started Setting up a printer Click Next. The Add Printer Wizard asks you to select your printer. TECHNICAL NOTE: If your printer is Plug and Play, the operating system recognizes it automatically. You can ignore the remainder of this section. See your printer manual. If the printer you are setting up: ❖...
Page 71: Turning Off The Computer
Click Next. The operating system prompts you to print a test page. If your printer is connected and turned on, click Next. To complete the setup procedure without printing a test page, click No, then click Next. Click Finish. You are now ready to print. Depending on your program, you may see various messages indicating the status of your print job.
Page 72: Caring For Your Computer
Cleaning the computer To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth. Ask your Toshiba dealer for suggestions for appropriate cleaning products. Keep liquid, including cleaning fluid, out of the computer’s keyboard, speaker grille, and other openings.
Page 73: Moving The Computer
To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com. Using a computer lock You may want to secure your computer to a heavy object such as your desk.
Page 74 Getting Started Caring for your computer Insert the cable’s locking end into the security lock slot, then rotate the key a quarter turn and remove it. The computer is now securely locked to deter computer theft. Locking the computer...
Page 75: Chapter 3: Learning The Basics
Chapter 3 Learning the Basics This chapter lists some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work temporarily stays in the computer’s memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working.
Page 76: Using The Keyboard
Learning the Basics Using the keyboard ❖ Back up your files to storage media on a regular basis. Label the backup copies clearly and store them in a safe place. If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy.
Page 77: Character Keys
Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The spacebar creates a space character instead of just passing over an area of the page. ❖ The lowercase l (el) and the number 1 are not interchangeable.
Page 78: Windows Special Keys
Learning the Basics Using the keyboard Windows special keys ® ® Windows special keys The keyboard provides two keys that have special functions in the operating system: ❖ The Windows ❖ The Application key has the same function as the secondary TouchPad control button (or secondary mouse button).
Page 79 Using the numeric keypad overlay To turn on the numeric keypad overlay, press simultaneously. The numeric mode light on the keyboard indicator panel glows when the numeric overlay is on. You can still use the overlay keys to type alphabetic characters while the numeric overlay is on.
Page 80: Starting A Program
Learning the Basics Starting a program To turn off the cursor control overlay, hold down the and press keyboard indicator panel goes out. Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows Explorer.
Page 81: Printing Your Work
To save: ❖ A file you are updating, open the program’s File menu and click Save. ❖ A new file, choose Save As from the File menu, type a name for the file, and click OK. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name.
Page 82: Backing Up Your Files
Learning the Basics Backing up your files Backing up your files Backing up your files means copying individual files to media, such as CD, or copying entire sections of your hard disk to another device, such as a tape drive. For those systems with a writable optional drive, you may back up file to a CD as follows: To back up to a CD or other media, insert the media into...
Page 83: Drive Components And Control Buttons
Using the DVD-ROM or multi-function drive HINT: Your DVD-ROM or multi-function drive is designed to play region 1 (North America) DVD-ROMs. TECHNICAL NOTE: Your DVD-ROM or multi-function drive is set to play region 1 (North America) DVD-ROMs. If you play a DVD disc from another region, the drive will automatically change to play in the format of the other region.
Page 84: Cd/Dvd Control Buttons
Learning the Basics Using the DVD-ROM or multi-function drive Never press the eject button or turn off the computer while the drive-in-use indicator light is glowing. Doing so could damage the disc or the drive. The eject button requires power to operate. The manual eject button does not require power.
Page 85: Cd/Dvd Control And Digital Audio Modes
Using the DVD-ROM or multi-function drive the mode button is locked, you cannot switch between the CD/DVD and digital audio modes. To unlock the mode button, press and hold it for four seconds. The previous track button returns to the preceding track on the disc.
Page 86: Inserting A Disc
Learning the Basics Using the DVD-ROM or multi-function drive Power is off and you press Play/Pause Operating system is running and you press Play/Pause Inserting a disc Before playing an audio CD, turn the volume down. Playing the compact disc at maximum volume could damage your ears.
Page 87 Using the DVD-ROM or multi-function drive The disc tray partially opens. To avoid damaging a disc or losing data, check that the disc activity light is off before opening the disc tray. Grasp the disc tray and pull it fully open. Hold the disc by its edges and check that it is clean and free of dust.
Page 88: Playing An Audio Cd
Learning the Basics Using the DVD-ROM or multi-function drive Gently press the center of the disc onto the spindle until it locks into place. Spindle Disc Positioning the disc on the spindle Make sure the disc is properly positioned on the spindle. If you position the disc incorrectly, it can jam the disc tray.
Page 89 Using the DVD-ROM or multi-function drive The Windows Media Player window appears. Rewind Play Stop Previous track Next track Mute Sample Windows Media The Windows Media an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button on the CD Player control panel.
Page 90: Viewing The Contents Of A Cd Or Dvd
Learning the Basics Using the DVD-ROM or multi-function drive Viewing the contents of a CD or DVD CDs and DVDs contain files just like the hard disk. CDs are often used to install software or store files that require lots of space, such as photographs and large presentation files.
Page 91: Removing A Disc With The Computer Off
Using the DVD-ROM or multi-function drive Removing a disc with the computer off Insert a slender object, such as a straightened paper clip, into the manual eject button access hole. Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it.
Page 92: Setting Up For Communications
Microsoft To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com. Connecting the modem to a phone line Your computer comes with a built-in modem. To use the modem, you must connect it to a standard voice-grade RJ-11 telephone line.
Page 93: Powering Down The Computer
To use a dial-up connection, have your network administrator configure your computer for the network and supply you with the telephone number for the dial-up connection. To set up the network connection, use the Dial-Up Networking Wizard: Click Start and point to All Programs. Point to Accessories, then to Communications.
Page 94: Using Shut Down
Learning the Basics Using Shut down TECHNICAL NOTES: Before using any of these options to power down your computer, save your files and make sure the disk activity lights are off. If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again.
Page 95: Stand By Command
operating system, and then returns to the state in which you left it. Factors when choosing Hibernation mode: ❖ While in Hibernation mode, the computer uses no battery power. ❖ Because the state of the system is held on the hard disk, no data is lost if the battery discharges.
Page 96: Turning Off More Quickly
You can also turn off the computer by pressing the power button or closing the display panel. To use either of these methods, you first need to turn on the feature in the Toshiba Power Management Utility. Click Start, Control Panel, then Performance and Maintenance.
Page 97: Starting Again After Shut Down
Sample Toshiba Power Management Advanced tab Click Apply. Click OK, then close the Control Panel. Starting again after Shut down To start the computer up again, press and release the power button. The on/off light turns on. Using Hibernation Follow these steps to power down the computer using Hibernation: Click Start, select Shut down computer.
Page 98 Click Start, Control Panel, then Performance and Maintenance. Double-click the Toshiba Power Management icon. Click the Advanced tab, and select the options you want. ❖ When I press the power button...
Page 99: Starting Again From Hibernation Mode
Sample Toshiba Power Management Advanced tab Click Apply. Click OK, then close the Control Panel. Starting again from Hibernation mode To start the computer from Hibernation mode, press and release the power button. The computer returns to the screen you were using.
Page 100: Using Stand By
Learning the Basics Using Stand by Using Stand by Follow these steps to power down the computer using the Stand by: Click Start, select Shut down computer. The Turn off computer box appears. Click Stand By. Sample Shut down computer dialog box The computer saves the status of all open programs and files to memory, turns off the display, and goes into a low-power mode.
Page 101: Going Into Stand By Mode More Quickly
Toshiba’s Power Saver utility. Open the Start menu, then click Control Panel. Click the Performance and Maintenance icon, and then click the Toshiba Power Management icon. Click the Advanced tab. Select Stand By for the options you want. When I press the power button Set this option to Stand By to put the computer into Stand by mode when you press the power button.
Page 102: Toshiba's Online Resources
Learning the Basics Toshiba’s online resources Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions, and keep you up to date with future upgrades. For more information, see “Contacting Toshiba”...
Page 103: Chapter 4: Mobile Computing
Many of these energy-saving features have been set by Toshiba. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you can use it for longer periods while traveling.
Page 104 Toshiba Web site at pcsupport.toshiba.com. To ensure that the battery maintains its maximum capacity, operate the computer on battery power at least once a month until the battery is fully discharged.
Page 105: Power Management
Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup changes, contact Toshiba’s Global Support Centre. Charging the battery Battery charge time may vary depending on the applications, NOTE power management settings, and features used.
Page 106: Charging The Rtc Battery
Mobile Computing Charging the battery To ensure that the battery charges to its full capacity, wait until it reaches room temperature (50 to 80 degrees Fahrenheit, 10 to 26 degrees Celsius). ❖ The battery is almost completely discharged. Leave the power connected, and the battery should begin charging after a few minutes.
Page 107: Monitoring Battery Power
Click Start, Control Panel, then Performance and Maintenance. Double-click the Toshiba Power Management icon. The current power source and battery power remaining section displays the current charge state of the battery. The value displays as a percentage of remaining battery charge.
Page 108: Conserving Battery Power
Mobile Computing Monitoring battery power Click the Battery Power Meter tab. Sample Toshiba Power Management Battery Power Meter tab TECHNICAL NOTE: The computer drains the battery faster at low temperatures. Check your remaining charge frequently if you are working in temperatures below 50 degrees Fahrenheit.
Page 109: What To Do When The Battery Runs Low
Toshiba’s power-saving options greatly increase the length of time you can use the computer before it becomes necessary to recharge the battery. Toshiba has combined these options into preset power usage modes. What to do when the battery runs low When the battery runs low you can ❖...
Page 110: Setting Battery Alarms
To set an alarm: Click Start, Control Panel, then Performance and Maintenance. Double-click the Toshiba Power Management icon. Click the Alarm tab and set the alarm, as desired. Sample Toshiba Power Management Alarm tab...
Page 111: Changing The Main Battery
Changing the main battery When your battery power is running low, you have two options—connect the computer to an AC power source or install a charged battery. When handling a battery, be careful not to drop it or short- circuit its terminals. Removing the battery from the computer Save your work.
Page 112: Taking Care Of Your Battery
Mobile Computing Taking care of your battery While still holding the release latch in the open position, gently lift the battery pack out of the computer. Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately following the advice in Taking care of your battery...
Page 113: Maximizing Battery Life
Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through toshiba.com. ❖ Reverse Polarity should be avoided with all batteries. The main battery is designed so that it cannot be installed in reverse polarity.
Page 114 Mobile Computing Taking care of your battery Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. If the battery light LED flashes or there is some other warning to indicate a low battery, go to step 4.
Page 115: Disposing Of Used Batteries Safely
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by Toshiba. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them. Under federal, state and local laws, it may be illegal to dispose of old batteries by placing them in the trash.
Page 116: Traveling Tips
❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cables, and compact discs. Contact your authorized Toshiba representative for more information.
Page 117: Xp Operating System
Chapter 5 Getting to Know the Windows System This chapter introduces the Windows by guiding you through a few basic tasks. If you have used a Windows will find the Windows Whether you have used a Windows the skill and confidence you will gain from this chapter will more than offset the short amount of time spent going through these lessons.
Page 118: Lesson 1: Exploring The Desktop
Getting to Know the Windows ® XP Operating System Lesson 1: Exploring the desktop Lesson 1: Exploring the desktop The desktop is the launching pad for everything you can do in the Windows start programs, find documents, set up system components, and perform most other computing tasks.
Page 119 The icons initially displayed on your system desktop include: Toshiba Access—Opens a window with links to software updates, services and support, and other important benefits. Recycle Bin—Holds files you’ve deleted using the Windows Explorer.
Page 120: Windows ® Xp File System
Getting to Know the Windows ® XP Operating System Lesson 1: Exploring the desktop Taskbar Each time you open a program, a button associated with that program appears on the taskbar. With some programs, a button appears on the taskbar for each document or window you open.
Page 121: Lesson 2: Using The Touchpad And Control Buttons Together
Getting to Know the Windows ® XP Operating System Lesson 2: Using the TouchPad and control buttons together Computers can be connected together to form a network, so that programs, documents and other data can be quickly and easily shared between computers. You can use the My Computer feature on the Start menu to access any file in the Windows For more information, read the Microsoft documentation that...
Page 122 Getting to Know the Windows ® XP Operating System Lesson 2: Using the TouchPad and control buttons together Sample desktop shortcut menu Click an empty area to close the shortcut menu. Use the TouchPad to move the pointer to the Start button.
Page 123 Getting to Know the Windows ® XP Operating System Lesson 2: Using the TouchPad and control buttons together Click an empty area of the taskbar at the bottom of the screen and, while holding down the primary button, use the TouchPad to drag the pointer to the right edge of the desktop, then release the primary button.
Page 124: Lesson 3: Learning About The Internet
Getting to Know the Windows ® XP Operating System Lesson 3: Learning about the Internet Lesson 3: Learning about the Internet This lesson demonstrates how to access a Web page from a window and from the taskbar. The lesson assumes you have an account with an Internet Service Provider (ISP).
Page 125: Lesson 4: Creating A New Document
Getting to Know the Windows ® XP Operating System Lesson 4: Creating a new document This lesson teaches you how to create a text file without having to first open a program. Move the pointer to an empty area of the desktop, then click the secondary button.
Page 126: Lesson 5: Creating A New Folder
Getting to Know the Windows ® XP Operating System Lesson 5: Creating a new folder Notice that when the document opens, there is a new button on the taskbar that reads My New Doc- Notepad (the name may be too long to fit into the taskbar space but, if you point to the name, the complete name is visible).
Page 127: Lesson 6: Starting Programs
Getting to Know the Windows ® XP Operating System The operating system displays the document as an icon on the desktop. Click the document icon and drag it toward your New Folder icon. Position the document icon over the New Folder icon until it changes color, then release the primary button.
Page 128 Getting to Know the Windows ® XP Operating System Lesson 6: Starting programs Sample Paint window To open the second program, click Start, then click All Programs. Point to Accessories, then click Windows Explorer. The operating system opens Windows Explorer, which provides access to all your computer’s resources.
Page 129: Lesson 7: Resizing, Repositioning, And Hiding Windows
Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows Sample Windows Explorer window Notice the taskbar now has two buttons on it—one for Paint and one for Windows Explorer. Click the Paint button on the taskbar. The operating system displays the Paint program.
Page 130: Using The Taskbar
Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows This lesson introduces several ways to adjust the size, shape, and position of windows open on the desktop. Using the taskbar If you have applications open on the desktop, you can rearrange them by pointing to the taskbar using the TouchPad and clicking the secondary button.
Page 131: Resizing And Moving Windows
Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows Click the Maximize button in the top-right corner of the Paint window. The Paint window expands to fill the screen, hiding everything except the taskbar. Notice that the Maximize button has changed.
Page 132: Lesson 8: Closing Programs
Getting to Know the Windows ® XP Operating System Lesson 8: Closing programs Repeat steps Windows Explorer, placing it on the right side of the desktop. Now that the windows are side by side, you can see how you could refer to one window while working in the other.
Page 133: Lesson 9: Creating Shortcuts
Getting to Know the Windows ® XP Operating System This lesson teaches you how to close the programs you opened earlier in this tutorial. To close the programs: Click the Close button at the top-right of the Explorer window. Windows Explorer closes, removing the Explorer button from the taskbar as well.
Page 134: Creating A Shortcut To The Character Map
Getting to Know the Windows ® XP Operating System Lesson 9: Creating shortcuts Sample Create Shortcut dialog box In the Command line box, type and click Next. The operating system prompts you to select a name for the shortcut. Type Calculator The operating system displays the new shortcut on your desktop.
Page 135 Getting to Know the Windows ® XP Operating System Sample Search options on the Start menu Click All Files and Folders. The operating system displays the Search Results dialog box. Sample Search Results dialog box Lesson 9: Creating shortcuts...
Page 136: Lesson 10: Changing The Screen Saver
Getting to Know the Windows ® XP Operating System Lesson 10: Changing the screen saver HINT: Search also allows you to perform searches on the Internet. Type char and then click Search. The operating system displays a list of all the files with “char”...
Page 137 Getting to Know the Windows ® XP Operating System Lesson 10: Changing the screen saver of these properties can be customized to meet your particular needs and tastes. DEFINITION: An object is an independent block of data, text, or graphics that was created by an individual application. This lesson introduces object properties by showing you how to change one of the properties of the desktop—the screen saver.
Page 138: Lesson 11: Setting The Date And Time
Getting to Know the Windows ® XP Operating System Lesson 11: Setting the date and time Click the arrow beside the current option to open the screen saver list box. Scroll through the screen saver options by clicking the scroll arrows in the list box. Try a screen saver pattern by clicking a name in the list box.
Page 139 Getting to Know the Windows ® XP Operating System Lesson 11: Setting the date and time Sample Date and Time Properties dialog box HINT: To open the Date and Time Properties dialog box more quickly, either click the time display on the taskbar with the secondary button, then click Adjust Date and Time, or double- click the time display.
Page 140: Lesson 12: Removing Objects From The Desktop
Getting to Know the Windows ® XP Operating System Lesson 12: Removing objects from the desktop Lesson 12: Removing objects from the desktop Earlier in this tutorial, you created a new icon on the desktop. Since everything you have done to this point has been just practice, you may want to return the desktop back to its original uncluttered state.
Page 141 Getting to Know the Windows ® XP Operating System Lesson 12: Removing objects from the desktop Sample Recycle Bin open on the desktop To completely remove an object, select it, and then click File, Delete. The object is permanently deleted from the Recycle Bin. Later on—in your real work, not in this tutorial—you will use the Recycle Bin to delete other objects such as folders, documents, and sometimes even programs.
Page 142: Lesson 13: Using System Restore
Getting to Know the Windows ® XP Operating System Lesson 13: Using System Restore To delete everything from the Recycle Bin at once, choose Empty Recycle Bin from the File menu. Click Yes to confirm that you are sure. HINT: Empty the Recycle Bin periodically. Even though an item is moved to the Recycle Bin, it still uses valuable space on the hard disk drive until it is deleted from the Recycle Bin.
Page 143: Lesson 14: If I Am Lost, What Do I Do
Getting to Know the Windows ® XP Operating System The operating system guides you through the process of storing your system settings for future use. It also guides you through restoring your system to the selected date or time. Lesson 14: If I am lost, what do I do? This lesson teaches you how to use some of the Help and Support features in Windows ®...
Page 144 Getting to Know the Windows ® XP Operating System Lesson 14: If I am lost, what do I do? The left side of the screen contains the index. The text box above the index, where the cursor is flashing, lets you type in a topic you want to find in the index.
Page 145: Using The Online Tours And Tutorials
Getting to Know the Windows ® XP Operating System program to look at it while you read about the program in the Help topic. Using the online tours and tutorials Whether you are new to computers or you have some experience, the Windows is a good place to start.
Page 146: Lesson 15: Turning Off Your Computer
Getting to Know the Windows ® XP Operating System Lesson 15: Turning off your computer Lesson 15: Turning off your computer It is very important that you let the Windows system shut down your computer. As it shuts down, the operating system performs a number of tasks that ensure that everything is in place the next time you turn on the computer.
Page 147: Chapter 6: Getting To Know The Windows Xp Media Center Edition
Chapter 6 Getting to Know the Windows Center Edition This section introduces you to the Windows Media Center Edition, a complete multimedia center where you can play your entire library of audio, video, and picture media on your computer, using either your computer’s keyboard, mouse, or the remote control.
Page 148: Media Center Setup
Getting to Know the Windows ® XP Media Center Edition Media Center Setup Media Center Setup This section shows you how to set up your computer to use the Media Center. Connecting the Computer to a Television Your computer has TV-out capability, meaning you can connect it to a television and view the computer image on the television.
Page 149: Connecting The External Remote Sensor
Getting to Know the Windows ® XP Media Center Edition Connect the AC adapter to a power source. Connect the square end of the USB cable to the computer’s USB port. Connect a coaxial cable to the port on the TV tuner. Connect the TV cable from your set-top box to the connector on the coaxial cable.
Page 150 Getting to Know the Windows ® XP Media Center Edition Media Center Setup Install batteries in the Windows Media Center remote control. Connecting the TV Signal Source Connect the signal source for your TV using a TV (IN) coaxial connector as follows: Plug the connector of a coaxial cable from your TV cable (wall or set-top box) into the coaxial connector on the external TV tuner on the computer, and carefully tighten...
Page 151 Getting to Know the Windows ® XP Media Center Edition Connecting the TV Signal Source When You Have an Existing Setup This section shows you how to connect the signal source from the wall to a VCR to a TV using coaxial cable. Remove the coaxial cable from the VCR input, and connect it to the input of a coaxial cable signal splitter (not included).
Page 152: Starting The Media Center
Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Starting the Media Center To start the Media Center: ❖ Click Start, and then click Media Center, or point the remote control at the remote sensor and press the Start button.
Page 153 Getting to Know the Windows ® XP Media Center Edition Media Center Setup Wizard To complete the Media Center Setup, follow the wizard on- screen prompts. When the wizard finishes, the Media Center main window displays. You can run Media Center side by side with other Windows NOTE software programs.
Page 154 Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Sample Media Center main window The Media Center main window is the central point for controlling all Media Center features. With a quick click of the mouse or using your remote control, you can: ❖...
Page 155: Remote Control For Media Center
Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Use the Media Playback controls at the bottom of the screen to control your movies, music, and photo displays. Media Playback controls Navigating Media Center In the Media Center windows, a selected item, such as a folder, file, or menu item is outlined with a green border.
Page 156 Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Using the remote control, you can: ❖ Navigate and control all Media Center windows. ❖ Control the video or live TV display. ❖ Place the computer in and out of standby mode. The remote control can send a strong signal to the remote sensor from within a range of about 26 feet and from an angle of about 45 degrees.
Page 157 Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Standby — Puts the computer into a power reduced standby state. Record — Records the selected television program and stores it on your hard disk. Stop — Stops the media currently playing. REW (Rewind) —...
Page 158 Getting to Know the Windows ® XP Media Center Edition Starting the Media Center My Videos — Opens the My Videos window. My Music — Opens the My Music window. My TV — Opens the My TV window. My Pictures — Opens the My Pictures window. Volume —...
Page 159 Getting to Know the Windows ® XP Media Center Edition The other direct access buttons open specific windows within the Media Center, such as the Television Program Guide, a DVD main menu, and live TV in full screen mode. ❖ Audio and Video —...
Page 160 Getting to Know the Windows ® XP Media Center Edition Starting the Media Center motion. To continue slow motion, you must press the FWD button more than once. Use Play to play selected media. Use FWD to move selected video or picture media forward. Press FWD up to three times to increase the fast fowarding speed.
Page 161: Watching Television Programs
Getting to Know the Windows ® XP Media Center Edition ❖ For DVDs, Skip moves to the next chapter. ❖ For videos and live TV and videos, Skip moves ahead 30 seconds. Use Replay to move backward second seconds in the selected audio or video file.
Page 162 Getting to Know the Windows ® XP Media Center Edition Watching Television Programs ❖ Pause, stop, rewind, and fast forward live TV, similar to the way you would control a DVD from a DVD player. ❖ Record a single TV show or an entire series. My TV will manage the recordings for you and give advanced warning if there are any recording conflicts.
Page 163: Selecting A Program From The Tv Guide
Getting to Know the Windows ® XP Media Center Edition Select a channel by using the Channel/Page (+ or -) buttons or by using the numeric buttons on the remote control. The channel number displays in the window. Using the arrow buttons, select the TV viewing window, and then press OK to maximize the TV window to full screen mode.
Page 164: Watching A Recorded Tv Program
Getting to Know the Windows ® XP Media Center Edition Watching Television Programs ❖ The TV Guide does not display past TV listings. Sample TV Guide screen ❖ Use the arrows at the top of the screen to display programs for later or earlier in the day. ❖...
Page 165: Searching For A Tv Program
Getting to Know the Windows ® XP Media Center Edition ❖ To watch a previously recorded TV program, on the My TV screen, click Recorded TV. On the remote control, click Start, and then My TV, and then Select Recorded ❖...
Page 166: Recording Tv
Getting to Know the Windows ® XP Media Center Edition Recording TV Use the arrow buttons to scroll through the search results, select a show, and then press OK. If multiple times for the show are displayed, select a time and press OK. Select Play in the window, and then press OK on the remote control to begin watching the program in full screen mode.
Page 167: Recording Tv Tips
Getting to Know the Windows ® XP Media Center Edition is currently being recorded. You can right-click the icon to open Media Center and stop recording. Media Center automatically records until the show is scheduled to be over as listed in the TV Guide. To make sure your show is being recorded, you can select TV Guide.
Page 168: Recording From The Guide
Getting to Know the Windows ® XP Media Center Edition Recording TV manually update the Guide before scheduling a recording. If you turn off (shut down) your computer, the Media Center NOTE will not record a scheduled program. Your computer must be turned on or in standby mode to record a TV program.
Page 169: Recording From Search
Getting to Know the Windows ® XP Media Center Edition Recording from Search To record a current or future show or series using Search: Press the Start button on the remote control, select My TV, and then select Search. Select Title, Keyword, or Categories. For Title and Keyword searches, enter your descriptive search words.
Page 170: Changing Your Settings
Getting to Know the Windows ® XP Media Center Edition Recording TV Enter the channel number using the numeric buttons on the remote control. Under Create a custom recording with, select Channel and time. Use the arrow buttons on the remote and +/- buttons on the screen to bring the selections into focus.
Page 171: Changing Recording Priorities
Getting to Know the Windows ® XP Media Center Edition Sample TV Settings screen This window allows you to change several settings that control how Media Center plays and records TV programs, as well as how it plays DVDs. In particular, you can change settings for: ❖...
Page 172: Listening To Music
Getting to Know the Windows ® XP Media Center Edition Listening to Music Press the START button on the remote, and then select My Select Recorded TV. Select Scheduled. Select Series. Select Change priorities. Use the up or down arrow on the screen to move a scheduled series up or down in the list of series priorities.
Page 173: Creating Your Music Library Using Windows Media Player
Getting to Know the Windows ® XP Media Center Edition Sample My Music screen Creating Your Music Library Using Windows Media Player Each time you add music files outside of Windows Media Player, you must use the Tools menu to add music files to your Windows Media Player Library for Media Center to find them.
Page 174: Adding Music From Your Hard Drive To Windows Media Player Library
Getting to Know the Windows ® XP Media Center Edition Listening to Music Click the Media Library tab to see where your new audio files have been placed. You can rename files by selecting the file and typing a new name or genre over the old one. The way you label your music files determines the category in which they are placed.
Page 175: Playing Digital Music Files
Getting to Know the Windows ® XP Media Center Edition Select Search to search all drives, or select Browse to search through a specific drive. Select the desired drive and then click OK. Windows Media Player searches the selected drives for all supported audio files and adds them to the Media Library.
Page 176: Finding Music Files In My Music
Getting to Know the Windows ® XP Media Center Edition Listening to Music Press the Start button on the remote control. Insert a CD into the CD drive — the CD plays automatically in Media Center. If you have other media such as live TV already playing when you insert the CD, Media Center asks you if you want to play the CD.
Page 177: Playing A Song
Getting to Know the Windows ® XP Media Center Edition Use the arrow keys to select a music file, and then press the Play button on the remote control to begin playing that music file. If you back up music files from a CD using Windows Media NOTE Player 9, you must log the files into the media player’s play list before you can play them using the Media Center.
Page 178: Finding And Playing An Album
Getting to Know the Windows ® XP Media Center Edition Listening to Music Use the arrow buttons to select Shuffle, and then press OK on the remote control. All songs in that genre are randomly played. Finding and Playing an Album In the Media Center Start menu, select My Music, and then select Albums.
Page 179: Creating A Playlist
Getting to Know the Windows ® XP Media Center Edition Creating a Playlist A playlist is a customized list of digital music files. Using playlists, you can group various digital music files together and determine the order in which you want the files to play. You can create a playlist that includes several tracks from various CDs or even a playlist that contains background music for a slide show.
Page 180: Displaying Your Pictures
Getting to Know the Windows ® XP Media Center Edition Displaying Your Pictures Displaying Your Pictures In My Pictures, you can: ❖ View pictures individually or as a slide show. ❖ Change transition time and display order of the pictures in your slide show.
Page 181: Viewing A Slide Show
Getting to Know the Windows ® XP Media Center Edition Your pictures are displayed just as you organized them in the My Pictures folder in Windows Explorer. Use the arrow buttons on the remote control to move through your picture files and folder files and select a picture.
Page 182: Watching Your Digital Movies
Getting to Know the Windows ® XP Media Center Edition Watching Your Digital Movies Watching Your Digital Movies The My Videos window in the Media Center makes it easy to play home video files you created or video files you downloaded from the Internet.
Page 183: Playing Digital Videos
Getting to Know the Windows ® XP Media Center Edition If not, move your videos into the My Videos or Shared Videos folder in Windows Explorer for Media Center to be able to find and play them. Once you have placed all your videos into the My Videos or Shared Videos folder, you can rename, add, delete, and organize them into folders.
Page 184: Playing A Video In Full Screen Mode
Getting to Know the Windows ® XP Media Center Edition Watching a DVD When the video is finished, select Restart and then press OK to replay the video, or select Done and press OK to close the file and return to the My Videos window. Playing a Video in Full Screen Mode On the Media Center Start menu, select My Videos.
Page 185: Stopping A Dvd Movie
Getting to Know the Windows ® XP Media Center Edition Select Yes or No. If you don’t select an option, the DVD autoplays in full screen mode after a few seconds. Press the Start button on the remote control. If a DVD menu appears, use the remote control or the mouse to select the DVD menu items and control the DVD movie playback.
Page 186: Playing A Dvd Movie Already In Your Drive
Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings ❖ Select Restart to begin playing the DVD at the beginning. ❖ Select Title Menu to go to the DVD main menu, if available. ❖ Select DVD Languages to change the language for the DVD soundtrack, subtitles, and menu.
Page 187 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Sample Media Center Settings screen Administrator Controlled Settings Some settings apply to all Media Center windows for all users and must be set up by the administrator. These settings are: ❖...
Page 188 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings User Controlled Settings Some settings can be selected by each person using the PC. These settings are: ❖ Sounds, Appearance, and Audio sets sound and display settings.
Page 189 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings ❖ Select Parental Control to set passwords, movie ratings, and other controls. ❖ Select Set up Internet connection to open the Internet Connection wizard. This allows you to set up your connection.
Page 190 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings To change the TV/DVD settings, use the arrow buttons to select an option, and then press OK on the remote control. Select OK in the window and then press OK on the remote control again to enter the changes.
Page 191 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Change TV Guide Settings In the Guide Settings, you can select which channels to display and you can manually update your Guide from the Internet. TV Guide settings are the same for each user and can be changed only by the administrator of the computer.
Page 192 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Changing Parental Controls for TV Viewing Only the administrator of the computer can change the Parental Control setting. This feature may not be available on your PC.
Page 193 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings In the DVD Settings window, select DVD, and then select Language. Use the arrow buttons to select the + or - buttons. Press the OK button on the remote control to scroll through the languages available.
Page 194 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings After you make your changes, press the Back button to return to the main Settings menu. Changing Picture Settings Each user can set his or her own picture settings. In the Media Center Start menu, select Settings.
Page 195: Chapter 7: Exploring Your Options
Chapter 7 Exploring Your Options In this chapter, you will explore other features of your notebook computer. ® Windows XP special features The Windows features and enhancements, including: ❖ New system file protection ❖ A system restore function, allowing you to rollback the system to its previous mode ❖...
Page 196: Personalizing Your Desktop
Exploring Your Options Personalizing your desktop Personalizing your desktop Your desktop is your virtual workspace. This section explains how to customize its features for the way you like to work. You can customize the following aspects of the desktop: ❖ Taskbar—which resources to display for quick access ❖...
Page 197: Bringing The World To Your Desktop
Bringing the world to your desktop With the Windows your desktop with complete World Wide Web integration at a single click. Turning on the Web content interface The first step to bring active content to your desktop is to turn on the Web content interface: Point to an empty space on the desktop and click the secondary button.
Page 198: Changing Desktop And Browsing Style
Exploring Your Options Personalizing your desktop To browse the Gallery for more components to add, click Visit Gallery. In order to browse, an active Internet connection must be established. To select some other Web site, type the address of the Web site you want or click Browse to locate it.
Page 199: Personalizing Individual Windows
The My Computer window appears. Select the Tools menu, then click Folder Options. The Folder Options dialog box appears. Sample Folder Options dialog box Click the preferred options. Click Apply, then OK. Personalizing individual windows Just as you can display a Web page on your desktop, you can also display a Web page in an individual window.
Page 200: Customizing Window Toolbars
Exploring Your Options Personalizing your desktop Customizing window toolbars You can display one or more customizable toolbars at the top of a window. As you browse, the operating system detects the kind of information presented in the window and automatically displays the appropriate toolbar buttons and menus.
Page 201: Displaying Information About Each Folder
The elements you can add to the top of the window are: Toolbar element Address Bar Standard buttons Displays buttons for commonly used Displaying a toolbar in a window Click Start, then click My Computer. The My Computer window appears. On the View menu, point to Toolbars, then click the name of the toolbar you want to display.
Page 202: Using Your Computer At The Office
Exploring Your Options Using your computer at the office Open the folder you want to view as a Web page. In the Tools menu, select Folder Options. In the Tasks section, click the button for Show common tasks in folders. Click Apply, then OK.
Page 203: Setting Up For Communications
Setting up for communications To connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: ❖ A modem (one comes with your computer) ❖ A telephone line ❖ A browser or communications program ❖...
Page 204: Connecting The Modem To A Telephone Line
Exploring Your Options Using your computer at the office To verify that the modem is set up properly, double-click the COM port to which your modem is connected. The Modem AMR Properties box appears. In the device status area, the computer should indicate whether the modem is working properly.
Page 205: Exchanging Data With Another Computer
Exchanging data with another computer To transfer a large amount of information between computers, you need a physical connection and a synchronization program. You can use the Windows synchronization program that transfers data using a cable connected to the computers’ parallel ports. Transferring files using a parallel port connection To transfer files using the computers’...
Page 206: Connecting To The Internet
Exploring Your Options Connecting to the Internet Connecting to the Internet To connect to the Internet you may need: ❖ A modem (one comes with your computer) ❖ A telephone line, DSL, a cable connection, or a satellite link ❖ A browser or communications program ❖...
Page 207: An Overview Of Using The Internet
An overview of using the Internet The following sections give a quick introduction to the Internet and some of its exciting features, under these headings: ❖ The Internet ❖ The World Wide Web ❖ Signing up with an Internet Service Provider ❖...
Page 208: Internet Service Providers
Exploring Your Options An overview of using the Internet Internet Service Providers To connect a computer directly to the Internet, many people and businesses use an Internet Service Provider (ISP). An ISP is a company that has the equipment and the telecommunication lines necessary to maintain an Internet connection.
Page 209: Internet Features
Internet features The Internet offers many types of communication tools to help you perform many tasks. ❖ Internet email To send and receive email of your own, you need a mailbox on the Web, or an email address. If you have an account with an ISP, you can probably set up an email address at the same time as you sign up for the service.
Page 210: Exploring Video Features
Exploring Your Options Exploring video features large amounts of data. You can also use the File Transfer Protocol (FTP) supported by a separate software program. Exploring video features Your computer’s video features provide the viewing of presentations or DVD movies on the computer screen. TECHNICAL NOTE: Video CD playback capability is not enabled on all systems.
Page 211: Display Settings Hot Key
Click the Settings tab. Slide the Screen area slider bar toward Less until the setting reads 800 x 600, then click Apply. The screen blinks momentarily while the settings are adjusted. The Monitor Settings window appears and asks if you want to keep the settings.
Page 212: Using A Microphone
Exploring Your Options Exploring audio features TECHNICAL NOTE: If you record MP3 files, you will only be able to play them on a device capable of playing MP3 files. Using a microphone Connect an external microphone to the computer. Click Start, point to All Programs, Accessories, Entertainment, then click Sound Recorder.
Page 213: Adjusting Recording Settings
Adjusting recording settings The better the quality of the recording, the more disk space the sound file requires. Experiment to find a balance that fits your needs. Open Sound Recorder, if necessary (click Start, point to All Programs, Accessories, Entertainment, then click Sound Recorder).
Page 214: Connecting A Monitor, Keyboard And Mouse
Exploring Your Options Connecting a monitor, keyboard and mouse Connecting a monitor, keyboard and mouse By connecting an external monitor, external full-size keyboard and a mouse, you can work with your notebook as if it were a standard office desktop computer. You can connect an external monitor to the RGB (monitor) port.
Page 215: Inserting Pc Cards
Inserting PC Cards Use caution when lifting or turning your computer. Failure to NOTE do so may result in damage to components, such as cables, attached to your computer, or to the computer itself. Before you insert a PC Card, refer to the documentation that comes with the card to see if you need to do anything before you insert it.
Page 216: Removing Pc Cards
Exploring Your Options Using PC Cards To avoid damaging the PC Card or the computer, don’t force the card into the PC Card slot. Removing PC Cards Stop the PC Card by clicking the Safely Remove Hardware icon on the System tray. After the Safe to Remove Hardware message appears, it is safe to remove the PC Card.
Page 217: Hot Swapping Precautions
Hot swapping precautions Although you can insert a PC Card at any time, to avoid data loss never remove a card while it is in use. For example: ❖ Never remove a hard disk card while the system is accessing it. ❖...
Page 218: Chapter 8: If Something Goes Wrong
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter. Your program stops responding.
Page 219 Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. Windows Task Manager Applications tab Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working.
Page 220 If Something Goes Wrong Windows Task Manager Shutdown menu, Turn Off option The computer shuts down. Your program performs an illegal operation. If you receive the message, “ ,” you should record the details of the message and operation consult the software manufacturer. To record the details: Click the Details button and select the text the operating system displays.
Page 221: Problems When You Turn On The Computer
Problems when you turn on the computer These problems may occur when you turn on the power. The computer will not start. Make sure you attached the AC adapter and power cable properly or installed a charged battery. Press and hold down the power button for a few seconds. If you are using the AC adapter, check that the wall outlet is working by plugging in another device, such as a lamp.
Page 222: The Windows Operating System Is Not Working
If Something Goes Wrong The Windows The Windows working Once you are familiar with the desktop and used to the way the operating system responds to your work routine, you can easily detect if the operating system is not working correctly. For example: ❖...
Page 223: Internet Problems
The Windows ❖ Safe Mode (with Command Prompt) ❖ Enable Boot Logging ❖ Enable VGA Mode ❖ Last known good configuration (your most recent settings that worked) ❖ Directory services restore mode (Windows controllers only) ❖ Debugging Mode ❖ Start Windows ❖...
Page 224: The Windows Xp Operating System Can Help You
If Something Goes Wrong Resolving a hardware conflict ® The Windows XP operating system can help you If the operating system has started properly, but you still have a problem using your computer, the online Help can assist you in troubleshooting the problem. To access Windows Click Start, then click Help and Support.
Page 225: A Plan Of Action
A plan of action The smooth operation of the system depends on the interaction of all devices, programs, and features. If the system or one of its attached devices isn’t working, resolving the problem can be time-consuming and frustrating. The recommended procedure for getting multiple devices to work together is to add and set up one device at a time.
Page 226: Fixing A Problem With Device Manager
If Something Goes Wrong Resolving a hardware conflict theory, if every device connected to the computer is Plug and Play-compliant, no two devices will compete for the same system resources. Simply plug in the device and turn on your computer. The operating system automatically sets up your system to accommodate the new device.
Page 227 Disabling or enabling a device Click Start, click the My Computer icon with the secondary button, then click Properties. The System Properties dialog box appears. Click the Hardware tab. Click the Device Manager button. Select the specific device from the device category. To enable a device, look at the far right of the toolbar.
Page 228: Memory Card Problems
If Something Goes Wrong Resolving a hardware conflict Click the Device Manager button. To view the device(s) installed, double-click the device type. To view the properties, double-click the device. The operating system displays the Device Properties dialog box, which provides an array of tabs. They include: ❖...
Page 229: Power And The Batteries
If removing the memory module eliminates the error, the memory module may be faulty. If the error recurs without the memory module installed, the error is not caused by the memory module. Toshiba recommends using only memory approved by NOTE Toshiba. Power and the batteries...
Page 230: Keyboard Problems
Let the battery discharge completely, then try charging it again. Check the power options using the Toshiba Power Management Utility. Have you added a device, such as a PC Card or memory module, that takes its power from the...
Page 231: Display Problems
If the problem occurs when both the keypad overlays are off, make sure the software you are using is not remapping the keyboard. Refer to the software’s documentation and check that the program does not assign different meanings to any of the keys.
Page 232 If Something Goes Wrong Resolving a hardware conflict ❖ Try adjusting the contrast and brightness controls on the external monitor. ❖ Press priority is not set for the built-in screen. The screen does not look right. You can change the display settings by clicking a blank area of the desktop with the secondary control button, then clicking Properties.
Page 233: Disk Drive Problems
Click OK. The display mode is set to Simultaneous and the external display device does not work. Make sure the external monitor is capable of displaying at resolutions of 800 x 600 or higher. Devices that do not support this resolution will only work in Internal/External mode.
Page 234 If Something Goes Wrong Resolving a hardware conflict The drive’s properties box appears. Click on Properties. Click the Tools tab. Click the Check now button. The Check Disk box appears (for example, Check Disk You can choose one or both options: ❖...
Page 235: Dvd-Rom Or Multi-Function Drive Problems
DVD-ROM or multi-function drive problems You cannot access a disc in the drive. Make sure the drive tray has closed properly. Press gently until it clicks into place. Open the drive tray and remove the disc. Make sure the drive tray is clean.
Page 236: Sound System Problems
If Something Goes Wrong Resolving a hardware conflict The color of the materials used to make the disc can affect its reliability. Silver-colored CD-ROMs are the most reliable, followed by gold-colored CD-ROM. Green-colored CD- ROMs are the least reliable. Sound system problems You do not hear any sound from the computer.
Page 237 Resource conflicts can cause problems when using PC Cards. “Resolving a hardware conflict” on page Card Information Structure When you insert a PC Card into a slot, the computer attempts to determine the type of card and the resources it requires by reading its Card Information Structure (CIS).
Page 238 If Something Goes Wrong Resolving a hardware conflict available, try the card in that machine. If the card malfunctions again, it may be defective. Resolving PC Card problems Here are some common problems and their solutions: The slots appear to be dead. PC Cards that used to work no longer work.
Page 239 Click Stop xxxx, where xxxx is the identifier for your PC Card. The operating system displays a message that you may safely remove the card. Remove the card from the slot. Never swap modules when the computer is in Hibernation or Standby mode.
Page 240: Printer Problems
If Something Goes Wrong Resolving a hardware conflict Printer problems This section lists some of the most common printer problems: The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the printer has plenty of paper.
Page 241: Modem Problems
Modem problems This section lists common modem problems: The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port and the telephone line jack. Check the port settings to make sure the hardware and software are referring to the same COM port.
Page 242 If Something Goes Wrong Develop good computing habits On a regular basis, back up the information stored on your hard disk. Here are some ways you can do this: ❖ Copy files to a CD or other media, following the steps in “Saving your work”...
Page 243: If You Need Further Assistance
GO, and then clicking the Detailed Specs link from the menu on the left, or just refer to the computer documentation shipped with your product. For the number of a Toshiba dealer near you in the United States, call: (800) 457-7777. If Something Goes Wrong If you need further assistance ®...
Page 244: Contacting Toshiba
Contacting Toshiba If you still need help and suspect that the problem is hardware-related, Toshiba offers a variety of resources to help you. You can access Toshiba on the Internet using any Internet browser by typing Toshiba voice contact Before calling Toshiba, make sure you have: ❖...
Page 245: Other Toshiba Internet Web Sites
Other Toshiba Internet Web sites toshiba.com computers.toshiba.com www.toshiba.ca www.toshiba-Europe.com www.toshiba.co.jp/index.htm http://servicio.toshiba.com Toshiba’s worldwide offices Australia Toshiba (Australia) Pty. Limited 84-92 Talavera Road North Ryde NSW 2113 Sydney Australia Belgium Toshiba Information Systems Benelux (Belgium) B.V. Excelsiorlaan 40 B-1930 Zaventem Belgium Czech Republic CHG Toshiba, s.r.o.
Page 246 Irvine, California 92618 United States 800-457-7777 (within the US) 949-859-4276 (outside the US - this call may incur long distance charges) France Toshiba Systèmes (France) S.A. 7, Rue Ampère 92804 Puteaux Cédex France Greece Ideal Electronics S.A. 109 Syngrou Avenue...
Page 247 Mexico Toshiba de México S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec. CP 11000 Mexico, DF. Tel: 5249-6500 The Netherlands Toshiba Information Systems Benelux B.V. Rivium Boulevard 41 2909 LK, Capelle a/d IJssel The Netherlands Papua New Guinea Fujitsu (PNG) Pty.
Page 248 If Something Goes Wrong Toshiba’s worldwide offices Spain Toshiba Information Systems (España) S.A. Parque Empresarial San Fernando Edificio Europa, 1a Planta Escalera A 28831 (Madrid) San Fernando de Henares Spain Switzerland Ozalid AG Herostrasse 7 8048 Zürich Switzerland United States Toshiba America Information Systems, Inc.
Page 249: Appendix A: Hot Keys
Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls. Instant password security Without a password The Fn + F1 key combination turns off the display and...
Page 250: Maintaining Security When The Battery Is Not Fully Charged
Hot Keys Instant password security the display’s content reappear. The Windows system log-on screen will appear, prompting you for a password. After typing in the password for the current user, press Enter. To activate the password feature: Click Start, Control Panel. Click Appearances and Themes.
Page 251: Sound
Sample power usage modes The power usage mode in the Windows under AC power is Full Power only. The properties of each mode are set in the Toshiba Power Management utility. This hot key cycles through the different alarm Hot Keys Sound ®...
Page 252: Stand By Mode
Hot Keys Stand by mode Stand by mode This hot key puts the computer into Stand by mode. Sample Stand by confirmation box ❖ A message box is displayed by default to confirm that the computer is going into Stand by mode. This message box can be set so it doesn’t display.
Page 253: Hibernation Mode
Hibernation mode This hot key puts the computer into Hibernation mode. Sample Hibernation confirmation box Hibernation mode ❖ If Hibernation mode is enabled (the default) a message box is displayed by default to confirm the computer is going into Hibernation mode. The message box can be set so it doesn’t display.
Page 254: Display Modes
Hot Keys Display modes Display modes This hot key cycles through the power-on display options. The display modes are: Sample display options window In o resolution of the internal display panel to match the resolution of the external display device. ❖...
Page 255: Enabling A Wireless Device
Enabling a wireless device This hot key enables/disables the optional wireless devices in your computer (for systems with Wi-Fi The wireless modes are: Wi-Fi enabled—This enables the Wi-Fi module. Wi-Fi disabled—This disables the Wi-Fi module. Disabling or enabling the TouchPad This hot key enables/disables the TouchPad.
Page 256: Appendix B: Power Cable Connectors
Appendix B Power Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada UL approved CSA approved Australia AS approved...
Page 257: Appendix C: Using Configfree™ With Your Toshiba Computer
Appendix C Using ConfigFree™ with your Toshiba Computer ConfigFree™ is a set of utilities used for configuring networks that use both wired and wireless network devices. These utilities include the following: ❖ Connectivity Doctor — The Connectivity Doctor utility is used to help fix networking problems with your notebook computer.
Page 258: Getting Started
Using ConfigFree™ with your Toshiba Computer Getting Started connection) between a personal computer and a Toshiba Wireless Projector. The Toshiba Wireless Projector utility must be installed in order to enable Quick Connect. For more information, see Getting Started This section contains information about the ConfigFree main screen, and how to start and configure ConfigFree.
Page 259: Starting Configfree
Help — Displays the online help file. Starting ConfigFree To start ConfigFree, do any of the following: ❖ (Microsoft and then point to All Programs. Point to the TOSHIBA ConfigFree folder, and then click ConfigFree. ❖ (Microsoft button, and then point to Programs. Point to the TOSHIBA ConfigFree folder, and then click ConfigFree.
Page 260: Configfree Utilities
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities ❖ Right-click the ConfigFree icon on the taskbar, and then click Options. For more information on configuring ConfigFree, see the online help. ConfigFree Utilities Connectivity Doctor The Connectivity Doctor displays the connection configuration and the status of all wired and wireless LAN devices that are connected to the network.
Page 261: Device Settings
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities The Connectivity Doctor The Connectivity Doctor screen automatically refreshes. However, you can also use the Refresh button to refresh the screen. Device Settings The Device Settings screen displays a list of all wired, wireless, and infrared devices that are connected to the network.
Page 262 Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Viewing the device settings ❖ Network Connections — Displays the Network Connection window, which contains detailed information about the network connection. ❖ Enable/Disable — You can easily enable or disable any of the listed devices simply by selecting the desired device, and then clicking the Enable/Disable button.
Page 263: Profile Settings
Using ConfigFree™ with your Toshiba Computer Profile Settings The Profile Settings utility displays a list of all the registered profiles in ConfigFree. You can also add, modify, and delete profiles; switch the profile being used; and view specific details about each profile.
Page 264: Quick Connect
Toshiba Wireless Projector. As a result, you will not be able to use the network to connect to a Toshiba Wireless Projector when the wireless LAN Configuration is set to Ad hoc. If you are connected to an access point, the connection will be broken and later re- established.
Page 265: Using Auto Switch
❖ If the Toshiba Wireless Projector utility is closed. ❖ If you select Toshiba Wireless Projector (DPJ) from the ConfigFree tray menu (this will disconnect the wireless LAN connection). ❖ If you select a profile from the ConfigFree tray menu or when you disable a wireless device.
Page 266: Auto Switch (Cable Disconnect)
Using ConfigFree™ with your Toshiba Computer Using Auto Switch ❖ From the Profile Settings screen, you can click the Auto Switch button. Auto Switch (Cable Disconnect) If a wired network cable is disconnected from the network, the Auto Switch (Cable Disconnect) option will automatically switch to another network device.
Page 267: Glossary
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. BIOS CD-ROM CD-RW CMOS COM1 COM2 alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory...
Page 268 Glossary DIMM DSTN DVD-ROM digital versatile (or video) disc read-only memory EPROM HTML IEEE LPT1 MIDI NTFS direct memory access dual inline memory module disk operating system dots per inch dual supertwist nematic digital versatile (or video) disc enhanced capabilities port erasable programmable read-only memory file allocation table Federal Communications Commission...
Page 269 PCMCIA SCSI SDRAM SRAM SVGA Terms The following terms may appear in this user’s guide. active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a “TFT display,” in its simplest form there is one thin film transistor (TFT) for each cell.
Page 270 Glossary alternating current (AC) — The type of power usually supplied to residential and commercial wall outlets. AC reverses its direction at regular intervals. Compare direct current (DC). application — A computer program that you use to perform tasks of a specific type.
Page 271 bus — An electrical circuit that connects the central processing unit (CPU) with other parts of the computer, such as the video adapter, disk drives, and ports. It is the pathway through which data flows from one device to another. See also bus speed, frontside bus. bus speed —...
Page 272 Glossary compatibility — The extent to which computers, programs, or devices can work together harmoniously, using the same commands, formats, or language as another. configuration — (1) The collection of components that make up a single computer system. (2) How parts of the system are set up (that is, configured).
Page 273 disable — To turn a computer option off. See also enable. disc — A round, flat piece of metal, designed to be read from and written to by optical (laser) technology, and used in the production of optical discs, such as CDs and DVDs. Compare disk. disk —...
Page 274 Glossary DVD-ROM (digital versatile [or video] disc read-only memory) — A very high-capacity storage medium that uses laser optics for reading data. Each DVD-ROM can hold as much data as several CD-ROMs. Compare CD-ROM. emulation — A technique in which a device or program imitates another device or program.
Page 275 — The physical components of a computer system. Compare software. Hibernate — A feature of many Toshiba notebook computers that saves to the hard disk the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 276 Glossary interlaced — A method of refreshing a computer screen, in which only every other line of pixels is refreshed. Interlaced monitors take two passes to create a complete screen image. Compare non-interlaced. internal device — See device. Internet — The decentralized, world-wide network of computers that provides electronic mail, the World Wide Web, and other services.
Page 277 megabyte (MB) — A unit of data equal to 1,048,576 bytes (1024 x 1024 bytes). See also bytes. memory — Typically refers to the computer’s main memory, where programs are run and data is temporarily stored and processed. Memory can be volatile and hold data temporarily, such as RAM, or it can be nonvolatile and hold data permanently, such as ROM.
Page 278 Glossary NT file system (NTFS) — An advanced file system designed for use specifically with the Windows NT operating system. online — Available through the computer. Online may refer to information being read from your own computer’s hard disk, such as online documentation or online help, or to information coming from another company on a company network or the Internet.
Page 279 processor — See central processing unit (CPU). program — A set of instructions that can be executed by a computer. The general classes of programs (also called software) are operating system, application, and utility. See also operating system, application, utility. properties —...
Page 280 Glossary ROM (read-only memory) — Non-volatile memory that can be read but not written to. By non-volatile, we mean that information in ROM remains whether or not the computer is receiving power. This type of memory is used to store your computer’s BIOS, which is essential instructions the computer reads when you start it up.
Page 281 universal serial bus (USB) — A serial bus that supports a data transfer rate of up to 480 Mbps (480 million bits per second). USB can connect up to 127 peripheral devices through a single all-purpose USB port. USB allows hot swapping of peripherals. See also bus, hot swapping, serial.
Page 282: Index
DVD-ROM or multi-function Internet 42 one-touch TV out 42 PC Card eject 40 power 42 Start 119 TOSHIBA Console 42 calculator 133 caps lock light 44 Card and Socket Services 214 CD and DVDs caring for 91 viewing contents 90...
Page 283 inserting 87 problem solving 235 channels DMA 225 Character Map 134 charging main battery 105 RTC (real-time clock) battery 106 checking device properties 227 cleaning CD or DVDs 91 computer 72 click 61 closing programs 132 comfort chair 49 lighting 50 work habits 51 commands Hibernate 94...
Page 284 Start button 119 system tray 120 taskbar 120 Device Manager 226 checking properties 227 disabling a device 227 dial-up connection 93 Dial-Up Networking Wizard 93 Digital Subscriber Lines (DSL) 206 disk activity light 44 Disk Defragmenter 234 disk drive corrupted/damaged data files 234 missing files/trouble accessing a disk 233 running slow 234...
Page 285 saving 75 transferring 205 Fn key 43 folders 120 displaying information 201 front panel 43 function keys 43 hard disk drive light 44 hardware conflicts 224 resolving 226 headphone jack 41 Help 143 Hibernate restarting 99 using 97 Hibernation 94 Hibernation mode 72 hiding windows 129 hot key...
Page 286 Windows special keys 78 lights 44 AC power 60 battery 60 caps lock 44 cursor control mode 45 disk activity 44 DVD-ROM/multi-function drive hard disk drive 44 numeric mode 45 on/off 43 lock slot 41 main battery changing 111 removing 111 memory problem solving 228 removing 66...
Page 287 232 checking device properties 227 compact discs not running computer hangs when PC Card computer will not power up 221 contacting Toshiba 243 corrupted/damaged data files 234 Device Manager 226 disabling a device 227 disk drive is slow 234...
Page 288 no sound 236 non-system disk or disk error 221 PC Card 236 checklist 237 error occurs 239 hot swapping fails 238 not recognized 239 slots appear dead 238 Plug and Play 226 power and batteries 229 printer 240 program not responding 218 program not working properly screen does not look right/flickers system resources 225...
Page 289 201 Toshiba Forum 244 Internet Web sites 245 online services 244 Toshiba Accessories information 35 TOSHIBA Console button 42 TouchPad 43 transferring files 205 transferring information between traveling tips 116 Turn Off turning computer on/off 42...
Page 290 SelectServ 36 Web address 208 Web browsers 207 Web content interface 197 Web sites 244 Web sites,Toshiba 245 windows hiding 129 repositioning 129 resizing 129 Windows Explorer 127 Windows Help 119 Windows Media Player 88 Windows Standby 71 Windows XP...

This manual is also suitable for:

P15-s479 P15-s409 - satellite - pentium 4 2.8 ghz Satellite p15 Satellite p15 series

Toshiba P15-S470 User Manual

Chapter 1: Finding Your Way Around

Chapter 2: Getting Started

Chapter 3: Learning the Basics

Chapter 4: Mobile Computing

Chapter 5 : Getting to Know the Windows

Chapter 6: Getting to Know the Windows XP Media Center Edition

Chapter 7: Exploring Your Options

Chapter 8: If Something Goes Wrong

Appendix A: Hot Keys

Appendix B: Power Cable Connectors

Appendix C: Using Configfree™ with Your Toshiba Computer

Quick Links

Related Manuals for Toshiba P15-S470

Summary of Contents for Toshiba P15-S470