Media Playback Via Usb Input - JVC LT-24VH4905 Instructions Manual

Table of Contents

Available languages

Install Type as Operator and the Satellite Operator

as the related M7 operator. Then highlight Preferred

Scan option and set as Automatic channel scan and

press OK to start the automatic search. These options

can be preselected depending on the Language

and Country selections that you made in the earlier

steps of the first time installation process. You may be

asked to select HD/SD or country specific channel list

according to your M7 operator type. Select one and

press OK to proceed.

Wait till the scan is finished. Now the list has been

installed.

While performing an M7 operator installation, if you

want to use the satellite installation parameters that

differ from the default settings select the Preferred

Scan option as Manual channel scan and press the

OK button to proceed. Antenna Type menu will be

displayed next. After selecting the antenna type and

the desired satellite in the following steps press OK

in order to change the satellite installation parameters

in the sub-menu.

In order to search for satellite channels other than

M7 channels you should start a standard installation.

Select the Install Type as Standard and press the

OK button to proceed. Antenna Type menu will be

displayed next.

There are three options for antenna selection. You can

select Antenna Type as Direct, Single Satellite Cable

or DiSEqC switch by using Left or Right buttons.

After selecting your antenna type press OK to see

the options to proceed. Continue, Transponder list

and Configure LNB options will be available. You can

change the transponder and LNB settings using the

related menu options.

• Direct: If you have a single receiver and a direct

satellite dish, select this antenna type. Press OK to

continue. Select an available satellite on the next

screen and press OK to scan for services.

• Single Satellite Cable: If you have multiple

receivers and a single satellite cable system, select

this antenna type. Press OK to continue. Configure

settings by following instructions on the next screen.

Press OK to scan for services.

• DiSEqC switch: If you have multiple satellite dishes

and a DiSEqC switch, select this antenna type. Then

set the DiSEqC version and press OK to continue.

You can set up to four satellites (if available) for

version v1.0 and sixteen satellites for version v1.1

on the next screen. Press OK button to scan the first

satellite in the list.

Analogue: If Analogue broadcast search option is

turned on, the TV will search for analogue broadcasts

after other initial settings are completed.

After the initial settings are completed TV will start

to search for available broadcasts of the selected

broadcast types.

While the search continues current scan results will

be displayed at the bottom of the screen. After all the

available stations are stored, Channels menu will be

displayed. You can edit the channel list according to

your preferences using the Edit tab options or press

the Menu button to quit and watch TV.

While the search continues a message may appear,

asking whether you want to sort channels according

to the LCN(*). Select Yes and press OK to confirm.

(*) LCN is the Logical Channel Number system that organizes

available broadcasts in accordance with a recognizable

channel number sequence (if available).

Notes:

To search for M7 channels after the First Time Installation,

you should perform the first time installation again. Or press the

Menu button and enter the Settings>Installation>Automatic

channel scan>Satellite menu. Then follow the same steps

mentioned above in the satellite section.

Do not turn off the TV while initializing first time installation.

Note that, some options may not be available depending on

the country selection.

Using Satellite Channel Table Feature

You can perform these operations using the Set-

tings>Installation>Satellite Settings>Satellite

Channel Table menu. There are two options regarding

to this feature.

You can download or upload satellite channel table

data. In order to perform these functions a USB device

must be connected to the TV.

You can upload current services and related satellites

& transponders in TV, to a USB device.

Additionally you can download one of the satellite

channel table files stored in USB device, to the TV.

When you select one of these files, all services and

related satellites and transponders in the selected

file will be stored in the TV. If there are any installed

terrestrial, cable and/or analogue services, they will

be kept and only satellite services will be removed.

Afterwards, check your antenna settings and make

changes if necessary. An error message stating "No

Signal" may be displayed if the antenna settings are

not configured properly.