Sharp PN-L702B Operation Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Monitor
  5. PN-L702B
  6. Operation manual

Sharp PN-L702B Operation Manual

Tft color lcd monitor
Hide thumbs Also See for PN-L702B:
Table of Contents

Advertisement

Quick Links

See also: User Manual , Setup Manual
PN-L702B
LCD MONITOR
OPERATION MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Sharp PN-L702B

Summary of Contents for Sharp PN-L702B

  • Page 1 PN-L702B LCD MONITOR OPERATION MANUAL...
  • Page 2 E or by the safety earth • The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. • The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red. Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified electrician. “WARNING: THIS APPARATUS MUST BE EARTHED.” Authorised representative responsible for the European Union Community Market Model No.: Serial No.: FOR CUSTOMERS IN U.K. IMPORTANT GREEN-AND-YELLOW: BLUE: BROWN: or coloured green or green-and-yellow. SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg Earth Neutral Live U.S.A. ONLY...

  • Page 3: Important Information

    IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: T O REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
  • Page 4 For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch. B. Information on Disposal for Business Users 1. In the European Union If the product is used for business purposes and you want to discard it: Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection facilities. For Spain: Please contact the established collection system or your local authority for take-back of your used products. 2. In other Countries outside the EU If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.

  • Page 5: Dear Sharp Customer

    DEAR SHARP CUSTOMER Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product. SAFETY PRECAUTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the following precautions carefully before using the product.
  • Page 6 SAFETY PRECAUTIONS (Continued) 1 9. B atteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment, dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below: • Use the specified batteries only. • I nstall the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the compartment. • Do not mix old and new batteries. • Do not mix batteries of different types. Voltage specifications of batteries of the same shape may vary. • Replace an exhausted battery with a new one promptly. • If you will not use the remote control for a long time, remove the batteries. • I f leaked battery fluid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or your clothing may cause a skin irritation or damage your eye.

  • Page 7: Tips And Safety Instructions

    - L anguage of OSD menu used in this manual is English by way of example. - I llustrations in this manual may not exactly represent the actual product or display. LED Backlight ● The LED backlight in this product has a limited lifetime. * I f the screen gets dark or does not turn on, it may be necessary to replace the LED backlight. This LED backlight is exclusive to this product and must be replaced by an authorized SHARP servicing dealer or service center. * P lease contact your local SHARP servicing dealer or service center for assistance.

  • Page 8: Mounting Precautions

    • Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such cases, please check the temperature condition specified by the optional equipments. • Do not block any ventilation openings. If the temperature inside the monitor rises, this could lead to a malfunction. • Do not place the monitor on a device which generates heat. • Do not use the product in locations where the unit is exposed to direct sunlight or other strong light.

  • Page 9: Table Of Contents

    (For SHARP dealers and service engineers) ...57  Pen tip (for touch pen): 2  Touch pen battery (LR-03 (“AAA” size)): 1  USB cable: 1  Eraser: 1  Tray: 1  Tray mounting fitting (cover / bracket): x 2  Tray mounting screws: M5 x 4 / M4 x 2  Terminal label: 1 Used when installing the interface expansion board PN-ZB01 (optional).  Cover Sharp logo: 1 Place this sticker onto the SHARP logo to cover the logo.

  • Page 10: Part Names

    When the PN-ZB01 (optional) is attached Caution • Consult your SHARP dealer for attachment/detachment of optional parts. • Do not open the expansion terminal cover by yourself. There are high voltage parts inside the cover which may cause an electric shock. Part Names 1. Touch pen ultrasonic sensor 2. Infrared transmitter/receiver 3.
  • Page 11 nRemote control unit 1. Signal transmitter 2. POWER button (See page 16.) 3. MUTE button (See page 21.) 4. VOL +/- buttons (See page 21.) BRIGHT +/- buttons (See page 21.) Cursor control ( 5. DISPLAY button (See page 21.) 6. MODE button (See page 21.) 7. INPUT button (See page 21.) 8. MENU button (See page 21.) 9. SIZE button (See page 21.) Part Names ) buttons...

  • Page 12: Connecting Peripheral Equipment

    Connecting Peripheral Equipment When the PN-ZB01 (optional) is attached Caution • Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected. • Be careful not to confuse the input terminal with the output terminal when connecting cables. Accidentally reversing cables connected to the input and output terminals may cause malfunctions and the other problems.

  • Page 13: Connection When The Pn-Zb01 (Optional) Is Attached

    Connection when the PN-ZB01 (optional) is attached The PN-ZB01 expansion board (optional) allows the use of additional connection terminals. 7. PC/AV DVI-D input terminal • Set DVI of INPUT SELECT on the OPTION menu according to the device to be connected. • Select the audio input terminal to be used in PC DVI-D or AV DVI-D of AUDIO SELECT on the OPTION menu. 8. PC RGB input terminals • Set BNC of INPUT SELECT on the OPTION menu to PC RGB when using the PC RGB input terminals. • Select the audio input terminal to be used in PC RGB of AUDIO SELECT on the OPTION menu. 9. AV component input terminals • Set BNC of INPUT SELECT on the OPTION menu to AV COMPONENT when using the AV component input terminals.

  • Page 14: Connecting The Power Cord

    Connecting the Power Cord Caution • Do not use a power cord other than the one supplied with the monitor. 1. Turn off the main power switch. 2. Plug the power cord (supplied) into the AC input terminal. 3. Plug the power cord (supplied) into the AC power outlet. Cable Cable clamp attachment Cable clamp The handles can be removed. Handle Caution • The removable handles and handle screws are for use with this monitor. Do not use them for any other devices. • To attach handles, be sure to use the handles and handle screws which were removed from the monitor. • Be sure the handles are attached securely. Binding Cables The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp.

  • Page 15: Preparing The Remote Control Unit

    Preparing the Remote Control Unit Installing the batteries 1. Press the cover gently and slide it in the direction of the arrow. 2. See the instructions in the compartment and put in the supplied batteries (R-6 (“AA” size) x 2) with their plus (+) and minus (-) sides oriented correctly. 3. Close the cover. TIPS • When the batteries become exhausted, replace them with new (commercially available) batteries. • The supplied batteries (R-6 (“AA” size) x 2) may become exhausted quickly depending on how they are stored. • If you will not be using the remote control for a long time, remove the batteries. • Use manganese or alkaline batteries only. Remote control operation range The operation range of the remote control unit is approx. 16.4 feet (5 m) at an angle of approx 10° from the center to the top/ bottom/right/left of the remote control sensor. 10°...

  • Page 16: Turning Power On/Off

    Caution • Turn on the monitor first before turning on the PC or playback device. Turning on the main power Caution • The main power must be turned on/off with the main power switch. Do not connect/disconnect the power cord or turn the breaker on/off while the main power switch is on. • When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds. • For a complete electrical disconnection, pull out the main plug. Turning Power On/Off Turning power on/off Press the POWER button to turn the power ON/OFF. Main power switch • Status of the power LED Green lit Orange lit...

  • Page 17: Disabling Power On/Off Operations

    If you already set the time but the date/time setting • screen appears when the power is turned on, the internal battery may be exhausted. Please contact your local SHARP servicing dealer or service center for assistance with battery replacement. • Estimated service life of the internal battery: About 5...

  • Page 18: Touch Pen Preparations/Touch Action

    Touch Pen Preparations/Touch Action Inserting the battery 1. Rotate the battery cap and remove it, and then pull out the cover. 2. Insert the supplied battery (LR-03 (“AAA” size)) in the orientation shown, and attach the cover and battery cap. TIPS • The supplied battery (LR-03 (“AAA” size)) may be exhausted in a short time, depending on how it was stored. • If the touch pen will not be used for an extended time, remove the battery from the touch pen. • For the battery, use an alkaline battery.
  • Page 19 Double-tap* Same action as double-clicking a mouse. Quickly touch twice with your finger/pen. When double-tapping with your finger, be sure to lift your finger sufficiently off the screen after the first tap. If there is insufficient distance between the screen and your finger, double-tap will not take place. Drag-and-drop Same action as drag-and-drop with a mouse. Touch the screen with your finger/pen and move without lifting. When you have finished the movement, lift your finger/pen. Flicks* Flick your finger/pen in the direction of the function you want to use. Flick your finger Press-and-hold* Same action as right-clicking a mouse. Press briefly with your finger/pen, and then lift your finger/pen from the screen. Touch Pen Preparations/Touch Action Pan* Use in a screen with a scrollbar. With your finger/pen touching the screen, move in the direction you want to scroll. The screen scrolls in the direction of the movement.

  • Page 20: Other Functions

    Touch Pen Preparations/Touch Action Press-and-tap Same action as right-clicking a mouse. With one finger touching the screen, tap once (single tap) with another finger. Tap once (single tap) with another finger With one finger touching TIPS • The screen may not respond correctly in the following cases: Touching is too quick The distance between the two points is too short The two points intersect • Operation with the touch pen is not possible. nPen actions Function Button 2 Pen tip Battery indicator Function Button 1 Function Button 1 Pressing Function Button 1 has the same action as right- clicking a mouse.

  • Page 21: Basic Operation

    1. INPUT (Input mode selection) The menu is displayed. Press mode, and press to enter. * You can select the input terminal by pressing the input switch of the monitor. Input mode Video PC D-SUB PC D-sub input terminal PC HDMI PC/AV HDMI input terminal AV HDMI PC/AV HDMI input terminal AV COMPONENT PC D-sub input terminal AV VIDEO PC D-sub input terminal When the PN-ZB01 (optional) is attached Input mode Video PC DVI-D...
  • Page 22 Basic Operation nSwitching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE ZOOM 1 ZOOM 2 NORMAL Dot by Dot TIPS • Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright Law, so please be careful. • When dual-screen display is selected, the screen size cannot be changed. • The appearance of the original video may change if you select a screen size with a different aspect ratio than the original image (e.g. TV broadcast or video input from external equipment). • When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen size to “NORMAL”.

  • Page 23: Menu Items

    Displaying the menu screen Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 24 to 27 for details of each menu items. Caution • Do not turn the main power switch off while the menu items are being displayed. Doing so may initialize the settings. nExample of operation (Adjusting CONTRAST in the PICTURE menu) MENU 1. Press to display the menu screen. SCREEN SCREEN PICTURE AUTO CLOCK AUDIO PHASE SETUP H-POS OPTION V-POS...

  • Page 24: Menu Item Details

    Menu Items Menu item details The menu will differ depending on the input mode. nSCREEN You can move the menu screen display position each time DISPLAY is pressed. AUTO (PC D-SUB/PC RGB) The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted. Pressing performs adjustment. Use this automatic adjustment when you use the PC D-sub input terminal or PC RGB input terminals to display a PC screen for the first time or when you change the setting of the PC. (See page 30.) CLOCK (PC D-SUB/PC RGB) Adjusts frequency for sampling clock for applicable video.
  • Page 25 USER Adjusts each item when the WHITE BALANCE is set to USER. R-CONTRAST ...Adjusts bright-toned red component. G-CONTRAST ...Adjusts bright-toned green component. B-CONTRAST ...Adjusts bright-toned blue component. R-OFFSET ...Adjusts dark-toned red component. G-OFFSET ...Adjusts dark-toned green component. B-OFFSET ...Adjusts dark-toned blue component. COPY TO USER Copies the value of white set for PRESET to the USER setting. MENU Select “ON” and then press (In the case other than white, color tone may differ from the PRESET.) GAMMA Selects the gamma. USER sets the gamma to the sent value (see page 35). (In PIP mode, the main side setting is reflected in the image.) DISPLAY COLOR PATTERN Displays a color pattern. Can be displayed while the menu screen is displayed, so you can refer to the pattern while adjusting the image.
  • Page 26 Menu Items HOT PLUG CONTROL Sets whether to use hot plug control for the PC/AV HDMI and PC/AV DVI-D input terminals. RS-232C/LAN SELECT Selects the method with which to control the monitor from the computer. ID No. SET Assigns ID numbers to monitors connected in a daisy chain (see page 33), using RS-232 cables.
  • Page 27 AUDIO OUTPUT (RCA) Sets the volume of sound output from the audio output terminals. When set to VARIABLE 2, sound will not be output from the built-in speaker or the external speaker terminal. VARIABLE1 ... You can adjust the volume using VOLUME. VARIABLE2 ... You can adjust the volume using VOLUME. FIXED ...Fixes the sounds. AUDIO LEVEL (STEREO MINI) Selects the maximum audio input level of the audio input terminal. SELF ADJUST On a PC D-SUB/PC RGB screen, specify whether to perform screen adjustment automatically or not. When ON is selected, the screen is automatically adjusted when its...

  • Page 28: Ndual Screen Display

    Menu Items nDual screen display You can display the screens of the PC input signal and AV input signal simultaneously. Set this function with “PIP MODES” in the PIP/PbyP menu. Main screen screen PbyP Main screen screen PbyP2 Main screen screen * The currently selected input signal is displayed on the main screen. * You cannot simultaneously display the screens of signals of the same type, such as two types of PC input signals or two types of AV input signals. * The dual screen display cannot be used with the combination of PC DVI-D and AV HDMI or of AV DVI-D and PC HDMI. TIPS • You might infringe on a copyright of the author which is protected by copyright law when you display the images of the computer screen and television/VCR simultaneously for profit-making or to show the image to the public.
  • Page 29 nSCHEDULE You can set the time to switch the monitor on and off. Set this function with “SCHEDULE” in the OPTION menu. (See page 26.) SCHEDULE – –/– –/– – – – – – – – –:– –:– – POWER DAY OF THE WEEK TIME – – – – – – –...

  • Page 30: Adjustments For Pc Screen Display

    Menu Items nADVANCED items (AV input) (See page 24 for additional Menu item details.) FLESH TONE Adjust the hue control. 3D-NR Reduce the noise of playback images on video. Setting a higher level reduces more noise. However, it may cause blurring on an image. MPEG-NR Reduce block noise caused by digital compression.

  • Page 31: Initialization (Reset)/Functional Restriction Setting (Function)

    Initialization (Reset)/Functional Restriction Setting (FUNCTION) You can return the settings to their factory-preset values and restrict operations. SIZE 1. Hold down until “F” appears in the upper left corner of the screen. 2. While “F” appears, press order. FUNCTION ALL RESET ADJUSTMENT LOCK ADJUSTMENT LOCK TARGET RS-232C UNLOCKED OSD DISPLAY TEMPERATUREALERT STATUSALERT POWER BUTTON...

  • Page 32: Controlling The Monitor With A Pc (Rs-232C)

    Controlling the Monitor with a PC (RS-232C) You can control this monitor from a PC via RS-232C (COM port) on the PC. You can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 33), you can make input mode selection/adjustment or can check the status of a specific monitor. Precautions when the PN-ZB01 (optional) is attached • To control the monitor via RS-232C, set RS-232C/LAN SELECT to RS-232C. • You cannot use RS-232C and LAN control simultaneously. PC connection nOne-to-one connection with a PC Connect with RS-232 straight cable between the PC’s COM port (RS-232C connector) and the RS-232C input terminal on the monitor.
  • Page 33 nResponse code format When a command has been executed correctly Return code , 0A A response is returned after a command is executed. * If an ID number has been assigned Space (20 ID number of responding monitor When a command has not been executed Return code , 0A * If an ID number has been assigned Return code...
  • Page 34 Controlling the Monitor with a PC (RS-232C) nCommands for ID control The command examples shown on this page assume the following connection and ID number set up. ID number: 1 ID number: 2 IDST ... A monitor receiving this command sets its own ID number in the parameter field. Example: IDST0001 OK 001 ← The ID number of this monitor is set to 1. TIPS You can automatically assign ID numbers by using the IDST command with the Repeater control (see “Repeater control”...

  • Page 35: Setting Of The Gamma User Data

    nRepeater control This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. You can use Repeater control function without assigning ID numbers. [Example] Set 1 Set 2 * If monitors are connected as shown above, you can execute a command like “Set all monitors’...

  • Page 36: Rs-232C Command Table

    Controlling the Monitor with a PC (RS-232C) RS-232C command table How to read the command table Command: Command field (See page 32.) Direction: W When the “Parameter” is set in the parameter field (see page 32), the command functions as described under “Control/Response Contents”. R The returned value indicated under “Reply” can be obtained by setting “????”, “ (repeater control) in the parameter field (see page 32). Parameter: Parameter field (See page 32.) Reply: Response (Returned value) *1: “●” indicates a command which can be used in power standby mode regardless of the STANDBY MODE setting.

  • Page 37: Screen Menu

    SCREEN menu Function Command Direction AUTO ASNC CLOCK CLCK PHASE PHSE POSITIONING POSITION OF HPOS THE LONGEST DIRECTION POSITION OF VPOS THE SHORTEST DIRECTION SIZE POSITION OF HSIZ THE LONGEST DIRECTION POSITION OF VSIZ THE SHORTEST DIRECTION RESOLUTION LONGEST HRES DIRECTION RESOLUTION SHORTEST VRES DIRECTION RESOLUTION RESET ARST Controlling the Monitor with a PC (RS-232C) Parameter Reply...

  • Page 38: Picture Menu

    Controlling the Monitor with a PC (RS-232C) PICTURE menu Function Command AUTO AGIN ANALOG GAIN ANGA ANALOG OFFSET ANOF CONTRAST CONT BLACK LEVEL BLVL TINT TINT COLORS COLR SHARPNESS SHRP RGB INPUT RANGE (AV HDMI) AHDR RGB INPUT RANGE (PC HDMI) PHDR RGB INPUT RANGE (AV DVI) ADVR RGB INPUT RANGE (PC DVI) PDVR RGB INPUT RANGE (D-SUB) PDSR RGB INPUT RANGE (PC BNC) PBRR ADVANCED FLESH TONE FLES (When the input...

  • Page 39: Audio Menu

    AUDIO menu Function Command Direction TREBLE AUTR BASS AUBS BALANCE AUBL RESET ARST SETUP menu Function Command Direction OSD H-POSITION OSDH OSD V-POSITION OSDV MONAURAL AUDIO MONO LANGUAGE LANG POWER ON DELAY PWOD OPERATION MODE FNCM STANDBY MODE STBM OFF IF NO OPERATION ATOF HOT PLUG CONTROL (DVI) HPCT HOT PLUG CONTROL (HDMI) HPCH RS-232C/LAN SELECT CTLS ID NUMBER ID NO. SETTING IDST...

  • Page 40: Option Menu

    Controlling the Monitor with a PC (RS-232C) OPTION menu Function Command DATE/TIME SETTING DATE DATE DISPLAY FORMAT DTFT TIME DISPLAY FORMAT TMFT SCHEDULE SC01- SC08 SCHEDULE BRIGHTNESS SB01- SB08 INPUT SELECT DVSL BNSL D-SUB SLDS HDMI HDSL AUDIO SELECT PC DVI-D ASDP PC HDMI ASHP PC D-SUB ASAP PC RGB ASCP AV DVI-D ASDA AV HDMI ASHA...
  • Page 41 PIP/PbyP menu Function Command Direction PIP MODES MWIN PIP SIZE MPSZ PIP POS THE LONGEST MHPS DIRECTION THE SHORTEST MVPS DIRECTION PIP POS LD+SD BATCH MPOS PIP BLEND MWBL PIP SOURCE MWIP SOUND CHANGE MWAD MAIN POS (Main screen) MWPP PbyP2 POS (Sub screen) MW2P AUTO OFF MOFF Initialization/Functional Restriction Setting (FUNCTION) menu Function Command Direction ALL RESET RSET ADJUSTMENT LOCK ALCK...
  • Page 42 Controlling the Monitor with a PC (RS-232C) Others Function Command SCREEN SIZE (PC) WIDE SCREEN SIZE (AV) WIDE VOLUME VOLM MUTE MUTE INFORMATION MODEL INF1 SERIAL NO SRNO BRIGHT VLMP TEMPERATURE SENSOR DSTA TEMPERATURE ACQUISITION ERRT CAUSE OF LAST STANDBY MODE STCA Commands for setting of the GAMMA user data Function Command RED GAMMA DATA TRANSFER UGRW...

  • Page 43: Controlling The Monitor With A Pc (Lan)

    Controlling the Monitor with a PC (LAN) When the PN-ZB01 (optional) is attached, your monitor can be connected to a LAN allowing you to control it from a PC on the LAN. You can also configure the monitor to send e-mail notification when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through). LAN terminal LAN cable (commercially available, straight) TIPS • You must assign an IP address to the monitor by following the procedures in “Settings to connect to a LAN”. (See the description on the right.) • Your PC must be installed with Internet Explorer (version 7.0 or later). • To control the monitor via LAN, set RS-232C/LAN SELECT to LAN. (See page 26.) • You cannot use RS-232C and LAN control simultaneously. Initializing personal information • When the PN-ZB01 (optional) is attached, personal information such as e-mail addresses can be registered in the monitor. Before transferring or disposing of the monitor,...
  • Page 44 Controlling the Monitor with a PC (LAN) ■ To set from a PC When the monitor is connected to a PC, LAN settings can be configured via PC. Set up process (1) Connect your monitor to a PC (2) Specify the PC’s IP address (3) Configure the monitor’s LAN settings (1) Connecting your monitor to a PC Connect a commercially available crossover LAN cable (UPT cable, Category 5) to the LAN port on the PC and this monitor. LAN terminal LAN cable (commercially available, crossover) (2) Specifying the PC’s IP address To configure the monitor’s LAN settings, you must temporarily change the settings on the PC.

  • Page 45: Controlling With A Pc

    6. Click on “LAN SETUP” under NETWORK. 7. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to “ON”. To set the address manually, set this to “OFF”. IP ADDRESS If the DHCP CLIENT is set to “OFF”, specify an IP address.
  • Page 46 Controlling the Monitor with a PC (LAN) ■ INFORMATION Information about this monitor appears. ■ CONTROL You can control the operations corresponding to the buttons POWER INPUT SIZE ) on the remote control unit. (See page 21.) TIPS • In standby mode, Power ON is the operation available. ■...

  • Page 47: Network (Lan Setup)

    ■ NETWORK (LAN SETUP) This screen allows you to set the settings necessary when the monitor is connected to a LAN. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to “ON”. To set the address manually, set this to “OFF”.

  • Page 48: Network (General)

    Controlling the Monitor with a PC (LAN) ■ NETWORK (GENERAL) This screen allows you to specify the general LAN settings. MONITOR NAME Specify a name for this monitor as it should appear on the Internet Explorer screen. AUTO LOGOUT TIME Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network.

  • Page 49: Mail (Recipient)

    ■ MAIL (RECIPIENT) This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error. RECIPIENT E-MAIL ADDRESSES Specify the e-mail addresses to send error notification e-mail CONDITION Specify the conditions to send mails. When you check PERIODICAL, specify the date and time to send the mails in the PERIODICAL setting.
  • Page 50 Controlling the Monitor with a PC (LAN) ■ SNMP You can configure settings related to SNMP. SNMP SETTING Set whether to enable or disable SNMP. VERSION Set the version of the SNMP to be supported. COMMUNITY NAME 1 to 3 Set the name of the community required for the access. USER 1 to 3 Set the user name, password, authentication method and other options required for access.

  • Page 51: Troubleshooting

    Power LED flashes red. “STATUS [xxxx]” appears in the corner of the screen. • Hardware has a problem. Turn off the monitor and request repair from your SHARP dealer. (When STATUS ALERT is set to OSD & LED. This varies depending on the setting.) The touch panel power LED lights red. • Hardware has a problem. Turn off the monitor and request...
  • Page 52 The monitor, however, will enter standby mode again if the cause of the temperature rise is not eliminated. (See page 8.) - C heck whether the monitor is placed at a location where a quick rise in temperature is likely. Internal temperature rises quickly if the vents on the monitor are blocked. - I nternal temperature rises quickly if dust accumulates inside the monitor or around the vents. Remove dust if possible. Ask SHARP dealer about removing internal dust.

  • Page 53: Specifications

    [ When PN-ZB01 (optional) is attached ] Dimensions (excluding protrusions) Weight Weight [PN-ZB01 (optional)] Cannot be used simultaneously. Does not support plug and play. Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such cases, please check the temperature condition specified by the optional equipments. In addition, check the requirements of the computer and other devices to be connected, and make sure that all requirements are satisfied. When AUTO INPUT CHANGE is set to OFF. When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. Specifications PN-L702B 70" Class [69-1/2 inch (176.6cm) diagonal] TFT LCD (pixels) 1920 x 1080 Approx. 1.06 billion colors 0.802 mm (H) × 0.802 mm (V) 160° right/left/up/down (contrast ratio ≥ 10) inch (mm) 60-9/16 x 34-1/16 (1538.9 x 865.6) Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω] Horizontal/vertical separate (TTL: positive/negative), Sync-on-green, Composite sync (TTL: positive/negative) NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM VESA DDC2B VESA DPMS, DVI DMPM HDMI x 1 Mini D-sub 15 pin, 3 rows x 1 3.5 mm mini stereo jack x 1...
  • Page 54 [116] 3-5/8 2-3/16 [92.5] [56] Opening width (61-11/16 [1567]) When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method. SHARP recommends using M6 screws and tighten the screws. Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch (8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times or more the weight of the monitor. nPower management This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in order for the monitor’s power management function to work.
  • Page 55 nCompatible signal timing (PC) Screen resolution VESA 640 × 480 800 × 600 848 × 480 1024 × 768 1152 × 864 1280 × 768 1280 × 800 1280 × 960 1280 × 1024 1360 × 768 1400 × 1050 1440 ×...
  • Page 56 Specifications PC/AV DVI-D input terminal pins (DVI-D 24 pin) Function TMDS data 2- TMDS data 2+ TMDS data 2/4 shield N.C. N.C. DDC clock DDC data N.C. TMDS data 1- 10 TMDS data 1+ TMDS data 1/3 shield 12 N.C. PC D-sub input terminal pins (Mini D-sub 15 pin) Function Red video signal input Green video signal input Blue video signal input N.C.

  • Page 57: Mounting Precautions (For Sharp Dealers And Service Engineers)

    (For SHARP dealers and service engineers) • When installing, removing or moving the monitor, ensure that this is carried out by at least 4 people. • Be sure to use a wall-mount bracket designed or designated for mounting the monitor. • This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials such as plaster / thin plastic board / wood before starting installation. This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor.
  • Page 58 PN-L702B Me EN11J(1)

Table of Contents